Question about 2011 Cadillac CTS Coupe

1 Answer

How do you replace worn linkage bushing on 2003 Cadillac CTS does it have to be welded

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where did you buy bushings

Posted on Dec 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tighten the shifter linkage on 93 grand maquise


Replace worn shift linkage bushings & possibly
Braze (weld) in some worn holes in linkage

May 10, 2014 | 1993 Mercury Grand Marquis

1 Answer

How to replace the ECM on a 2003 cadillac cts


unblot it , unplug it and replace . then take it to the dealer so they can remarry all the other modules to the pcm .

Feb 26, 2014 | 2003 Cadillac CTS

1 Answer

2008 ecm p0008


- Engine mechanical problems
- Incorrect timing chain
- Stretched timing chain
- Failed camshaft actuator or actuator solenoid

Aug 27, 2013 | 2003 Cadillac CTS

1 Answer

93 suburban inkage off? Starts in neutral not in park


You will have to remove ALL shift linkage & replace
any worn bushings & possibly weld up worn areas &
file out to,get things back in working order

Your dealing with lots of rust,a lot of it,lots of use & wear

Best to completely remove it all & have it media blasted,then
rehab & paint the pieces

Mar 22, 2013 | Cars & Trucks

1 Answer

Replacing bushings for the rear on a 2004 cadillac cts 3.6L


The howling is more likely rear hub
bearings- in wheel knuckle assy

Check for differential axle seal leaks
& check fluid level before that goes bad

I have a 2004 Lincoln LS with similar rear
drive & no problems with dry rot & it sits outside

Replace the worn parts

Try Rock Auto.Com & try for Moog Parts

The Stabilizer Links are shot for sure front & back

Mar 06, 2013 | Cadillac CTS Cars & Trucks

1 Answer

How to install camshaft on cadillac cts 2003


i had replace both head gaskets but can remember how to place the camshafts or the markings on the 2003 cts 3.2 motor

Oct 10, 2012 | 2003 Cadillac CTS

1 Answer

2003 cadillac CTS manual shift - shift balks at going into 4th slot


you would be closer to the problem than the dealer
taking it as a column shift , it is very possible that the plastic slides on the selectors out side of the box are badly worn or the rods them selves are worn out

Sep 09, 2017 | Cadillac CTS Cars & Trucks

1 Answer

2003 CTS Automatic when i change gears from drive to park or park to drive i hear a clanking noise when i change the gears. If someone is standing there when you pull up and you put the car in park......


I had the same noise on my wife`s 03 cts. It was the the rubber bushing on the shifting arm from the shift lever to the trans. The arm was 250.00 plus I installed myself. Very easy to get to. Bad design should not have went bad.

Dec 01, 2011 | 2003 Cadillac CTS

1 Answer

2003 Cadillac CTS. Shift linkage makes metallic sound when shifting. Sounds like it is loose. Shift selector does not feel crisp when shifting. Want to access to tighten/check. How??


Just had the same problem. The problem is that the rubber bushing on the transmission linkage deteriorates and falls off. This causes two problems - shifter is loose and a metallic clunking sound is heard when shifting. It's not the shifter inside the car. It's the linkage underneath the car. You have to buy the bushing (if sold by itself) or the linkage kit. The linkage is on the passenger side of the transmission between transmission and right side exhaust pipe. Ensure engine/exhaust is cold prior to trying to access. Regards.

Aug 06, 2010 | 2003 Cadillac CTS

Not finding what you are looking for?
2011 Cadillac CTS Coupe Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...