Question about 2001 Kia Sportage

1 Answer

Can not figure out how to adjust the clutch. - 2001 Kia Sportage

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

I would bet money that the clutch is hydraulic and non adjustable like all others made after 1990. I have not seen a mechanically operated clutch in anything made since 1980.

Posted on Nov 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 93 isuzu pickup and my clutch is slipping from time to time it is cable driven and im trying to figure out how to adjust it and where adjustment is located


I Do Not Think It Is Adjustable, I Would Say That The cable Is now Getting Stuck Inside The Outer Cable Best Is To Fit New cable

Mar 21, 2013 | 1993 Isuzu Pickup

1 Answer

When I go to shift the rpms jump up but there is not much power,feels like it is lagging


Thank you for the clarification, if this is happenning when you have the clutch out, I would suspect that your clutch is slipping. Does the engine rev, but you don't go any faster? If this is the case, and it being a hydraulic clutch, (meaning that there is no real adjustment) then it probably means that your clutch is bad. If these are not your symtoms, then contact us and we'll figure it out.

Jan 13, 2011 | 2003 Hyundai Santa Fe

2 Answers

I cannot get the car into gear. It is a manual transmission. Is there a spot where fluid goes in for the clutch?


Your clutch is not hydraulic but is supposed to self adjust. Try the procedure below to help it adjust. If it will not adjust, the clutch may be worn out.


ADJUSTMENT

Free-Play See Figures 8, 9 and 10
The clutch free-play is adjusted automatically by a built-in clutch control mechanism. This device allows the clutch controls to self-adjust during normal operation.
The system consists of a spring-loaded gear quadrant, a spring-loaded pawl and a clutch cable which is spring-loaded to preload the release lever bearing. This compensates for movement of the release lever, as the clutch disc wears. The pawl, located at the top of the clutch pedal, engages the gear quadrant when the clutch pedal is depressed and pulls the cable through its continuously adjusted stroke. Clutch cable adjustments are not required because of this feature.
jturcotte_253.gif

Fig. Fig. 8: Clutch self-adjusting system component identification for the 3.8L engine


CHECKING ADJUSTMENT
The self-adjusting feature should be checked every 5,000 miles (8,000 km). This is accomplished by ensuring that the clutch pedal travels to the top of its upward position. Grasp the clutch pedal with your hand or put your foot under the clutch pedal, and pull up on the pedal until it stops. Very little effort is required (about 10 lbs./4.5 kg). Finally, depress the clutch pedal and listen for an audible "click.'' If you hear a sound, the clutch was in need of adjustment, and it has just adjusted itself.

Nov 23, 2010 | 1998 Ford Mustang

2 Answers

How to adjust clutch pedal on 86 mustang lx


clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:


REMOVAL & INSTALLATION


See Figure 1

  1. Disconnect the battery cable from the negative terminal of the battery.
  2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
  3. Remove the lower dash panel section to the left of the steering column.
  4. Remove the shrouds from the steering column.
  5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
  6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
  7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
  8. Disconnect all electrical connectors from the steering column.
  9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
  10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
  11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
  12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
  13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
  14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:
  1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
  2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
  3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
  4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
  5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
  6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
  7. Attach the clutch cable to the quadrant.
  8. Position the steering column onto the four studs in the support bracket and start the four nuts.
  9. Connect the steering column electrical connectors.
  10. Install the steering column shrouds.
  11. Install the brake pedal support lateral brace.
  12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
  13. Install the lower dash panel section.
  14. Install the steering wheel.
  15. Connect the battery cable to the negative terminal on the battery.
  16. Check the steering column for proper operation.
  17. Depress the clutch pedal several times to adjust the cable.
  18. 714c4a4.gif

Sep 24, 2010 | Ford Mustang Cars & Trucks

1 Answer

1994 Ford Probe GT Transmission


OK..............There is no transmission fluid just clutch fluid. Its in a small reservoir on the firewall. I think you have a worn clutch or it needs the lines adjusted. If the clutch doesn't engage until the pedal it almost at the top then you need to adjust it or replace it. The cleaner you put in is irrelevant to your problem. There is gear oil in the transmission though but that's not the problem either. The clutch cable is easy to adjust, just loosen the lock nut and spin the cable adjuster until the pedal feels right. Hope this helps :)

Jul 05, 2010 | 1994 Ford Probe

1 Answer

Clutch not fully disengaging and clutch pedal has alot of play


The next idea is you need to get under the car, have somebody push the pedal and see how far the slave is moving the rod which is move the throwout fork which is move the bearing. With a little work and a flashlight you can figure this problem out pretty easy. There is a rod that attaches to the clutch pedal that is adjustable. Loosen the lock nut and screw the rod out to lessen the amount of free play. You might no have the clutch plate aligned. Hope this helps :)

Nov 22, 2009 | 1990 Chevrolet Cavalier

2 Answers

My Nissan 1987 hard body truck has its clutch very losse


Thank you but I already figured it out. It was the clutch master cylinder the need to be replaced. I might change also the clutch slave cylinder also just to work even better. good bye

Nov 10, 2009 | 1987 Nissan Pickup

1 Answer

I need to tear down my transmission in a 1988 Chevrolet Cavalier Z24 2.8L i am fixing the clutch and i need diagrams on how to take it apart and put it back together


Below is process for removing and replacing the clutch assembly.
Hope this helps, good luck.
Regards,


REMOVAL & INSTALLATION


See Figures 1, 2 and 3



0900c1528003be16.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Exploded view of the clutch disc and cover assembly
  1. Disconnect the negative battery cable.
  2. If equipped with a cable clutch (1982-84 vehicles), disconnect the cable at the clutch release lever and transaxle, as outlined earlier in this section.
  3. For 1985-94 vehicles remove the sound insulator from inside the vehicle. Disconnect the clutch master cylinder pushrod from the clutch pedal.




0900c1528003be17.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Disconnect the clutch actuator (slave) cylinder line - 1995-96 vehicles
  1. Remove the transaxle, as outlined earlier in this section.
  2. Mark the pressure plate assembly and the flywheel so that they can be assembled in the same position. They were balanced as an assembly at the factory.
  3. Loosen the attaching bolts one turn at a time until spring tension is relieved.
  4. Support the pressure plate and remove the bolts. Remove the pressure plate and clutch disc. Do not disassemble the pressure plate assembly; replace it if defective.
  5. Inspect the flywheel, clutch disc, pressure plate, throwout bearing and the clutch fork and pivot shaft assembly for wear. Replace the parts as required. If the flywheel shows any signs of overheating, or if it is badly grooved or scored, it should be refaced or replaced.




0900c1528003be18.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: You must follow the specified sequence when tightening the pressure plate retaining bolts
To install:
  1. Clean the pressure plate and flywheel mating surfaces thoroughly.
  2. Position the clutch disc and pressure plate into the installed position, and support with a dummy shaft or clutch aligning tool, tool J 29074 or equivalent. The clutch plate is assembled with the damper springs offset toward the transaxle. One side of the factory supplied clutch disc is stamped "Flywheel Side".
  3. Install the pressure plate-to-flywheel bolts. Tighten them in the sequence shown in the accompanying figure, as follows:
    1. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 12 ft. lbs. (16 Nm).
    2. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 15-22 ft. lbs. (22-30 Nm) plus an additional 30° turn.
    3. Remove the clutch alignment tool.

  4. Lubricate the outside groove and the inside recess of the release bearing with high temperature grease. Wipe off any excess. Install the release bearing.
  5. Install the transaxle, as outlined earlier in this section.



WARNING When adjusting the cruise control switch, do NOT exert an upward force on the clutch pedal pad of more than 20 lbs. (89 N) or damage to the master cylinder pushrod retaining ring may result.

  1. For 1985-94 vehicles, attach the clutch master cylinder pushrod to the clutch pedal and secure with the retaining clip. If equipped with cruise control, check the switch adjustment at the clutch pedal bracket. Install the sound insulator.
  2. If equipped with a cable clutch, attach the clutch cable at the transaxle and clutch release lever. Check the clutch operation by lifting the clutch pedal up to allow the mechanism to adjust the cable length. Depress the pedal slowly a few times to set the pawl into mesh with the quandrant teeth.


ADJUSTMENTS


All 1982-84 models have a self-adjusting clutch mechanism located on the clutch pedal, eliminating the need for periodic free play adjustments. The self-adjusting mechanism should be inspected periodically as follows:
  1. Depress the clutch pedal and look for the pawl on the self-adjusting mechanism to firmly engage the teeth on the ratchet.
  2. Release the clutch. The pawl should be lifted off of the teeth by the metal stop on the bracket.

On 1985 and later models, the hydraulic clutch system provides automatic clutch adjustment. No adjustment of clutch linkage or pedal position is required.

May 04, 2009 | Chevrolet Cavalier Cars & Trucks

1 Answer

1983 Ford Ranger Gear grinding


Your clue is probably that when you pump the clutch twice that it works. I don't know about the 83's but the 96 or so on up have automatic clutch adjustment & when the clutch is worn out that part will not adjust anymore and will create the problem, just like th 97 that i have & haven't changed the clutch yet... (too lazy - waiting for it to totally quit before i fix it) So my guess is that if you haven't changed the clutch, pressure plate t/a bearing stuff, you may need to do that. Ford guys should have told you that.... hope this helps, rick

Apr 17, 2009 | 1995 Ford Ranger Supercab

2 Answers

Trying to figure out how to adjust the clutch on a 2005 Toyota Corolla style s


You car does not have an "adjustable" clutch. The Corolla uses a hydraulic clutch. The action of the hydraulics eliminates the need for adjustements. If the clutch is slipping, you may need to replace the clutch.

Jan 15, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?

Open Questions:

See all 2001 Kia Sportage Questions

2001 Kia Sportage Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...