Question about Ford F-350

Open Question

2004 f350. No brake lights.Tail lights & blinkers work fine,checked fuses and bulbs.Replaced brake swith in pedal.Is there a relay.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

j_del
  • 1586 Answers

SOURCE: Tail/brake light bulb replacement 2004 Olds Alero

In the trunk, in the rear corners, you'll see some plastic "caps" with tabs on them, similar to wing nuts. Remove those, and the taillight comes right off the back of the car. That will allow you to replace the bulbs.

Posted on Aug 25, 2008

johnny5846
  • 379 Answers

SOURCE: 2001 dodge neon tail lights inop

looking at your schematics and , you say tail lights don't work , you didn't mention if front parking lights and license plate lights are working , they all come from the same source , a black /yellow wire , a good clue if front work and rear don't , please advise .if fronts work then you have a open circuit somewhere between junction S118 (near breakout for left headlamp) and rear sockets.

Posted on Dec 31, 2008

MrScary66613
  • 1990 Answers

SOURCE: Left rear brake light stopped working but bulb and fuses are OK.

These are Dual Function Bulbs. They control the Parking Lights and the Brake Lights. This Bulb is Burnt out on the Brake Coil inside the Bulb. I have actually seen Bulbs that were Bad But you could not Tell by jast looking at them. It should be fine with a New Bulb. Please Rate My Response! Thanks!

Posted on Feb 05, 2009

  • 1 Answer

SOURCE: 2001 ford explorer sport trac

Just found the answer on another site. Sure enough went out removed the 3 philips head screws in the steering column opened it up and walla a wire connection had pulled itself free. When my son uses my truck he always uses the tilt steering, when I get in I have to readjust it. because of this the wire connection pulled itself out. I simply pushed it back in an blinker and brake light are now working. My husband is now trying to figure a way to secure the wire connection so it doesn't pull itself out again. Hope this helps others, either by saving the cost of a dealership or machanic or from getting rear ended.

Posted on Mar 21, 2009

  • 7353 Answers

SOURCE: 96 monte carlo rear window brake light works but

are the bulbs good. do these use the same bulbs for brake/turn signals?. if the high mount light was working, then the brake light switch was good. brake light power goes through the turn signal switch. you will need to get a wiring diagram and verify the power is going in and coming out of turn signal switch.

Posted on Sep 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 f350 cab and Chasse front blinkers work but my back blinkers and brake lights don't work


brakes and turn signal lights work together not tail and turn your mistaken

Jul 15, 2017 | Cars & Trucks

1 Answer

Blinkers work tail lights work but no brake light. Mitsubishi mirage 2001


check fuses firs, then check the bulbs . If they are all fine check the brake light switch at the top of the brake pedal in the driver's footwell

Jul 04, 2015 | Mitsubishi Cars & Trucks

2 Answers

My brake lights and rear blinkers are not working. I have replaced the bulbs in both brake lights. What next?


most blinkers uses relays, and when they flashes fast one light is out, but you replaced your burnt bulb might be a bad relay.

Sep 17, 2012 | 2007 Hummer H2 SUT

1 Answer

Brake Lights and Hazard still dont work


TEST FRONT RIGHT BLINKER CIRCUIT AND REPLACE THE BULB,,WITH PROPER BULB...A DOUBLE CIRCUIT BULB IN A SINGLE SOCKET WILL DO THAT ALSO A SINGLE SOCKET BULB IN A DOUBLE SOCKET HOLDER....CHECK LEFT SIDE BULB FOR ACURANCY

Aug 29, 2009 | 1993 Chevrolet Astro

2 Answers

Turn signals work but the brake lights do not how do i get them to work? i already changed the flasher.


I have a 2001 Ford F150, my brake lights dont work. Ive replaced the bulbs, checked the fuses,and the brake switch on side of the brake pedal was replaced. I still dont have any brake lights. My third brake light works fine, along with my running lights,flashers, blinkers.

Jun 18, 2009 | 1985 Ford F150

1 Answer

I have a short to ground problem with my tail/crtsy light circuit ( keeps poppin fuses when the light swith is pulled to on position) also dash lights & tail lights don't work but interior light is on...


Try removing the bulbs from the rear tail lights you have one 2 bulb system shorting out, so one at a time remove the bulbs then replace the fuse and see which one is bad or just buy new bulbs and replace, also could be front running light blinker light. But sounds like brake light to ground threw bulb.

Jun 13, 2009 | 1985 GMC S-15

1 Answer

2001 dodge ram 1500 brake lights


I would guess the brake fuse ( this does not use the same fuse as the tail lights/blinkers) or the ground for the brake light bulb.

Aug 13, 2008 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

My tail lights dont work, its not a fuse, my blinkers and reverse lights work, its just my running lights and my brake lights that dont, any suggestions?


check the wire harness that runs from inside the trunk on the drivers side follow it down to the tail light and make shure the wires are not damaged or unplugged remove cover on the drivers side inspect the bulbs the holders and the wires and dont forgt to retighten all grounds that you find on your travels this should get the rear tail lights working also check the brake pedal switch up on the metal part of the brake pedal arm follow it up tp the brake pedal switch and acuate the switch by hand and check the wire voltage coming in and going out when pressing the brake pedal ok give this a shot

Jul 21, 2008 | Ford Mustang Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...