Question about 2001 Volkswagen Beetle

Open Question

Turn signal and hazard lights not working at all. Replaced Hazard fuse relay, checked appropriate turn signal fuses, all are okay. All bulds are ok as indicated when alarm activated with key fob. All flash as indication doors are locked. One day the turn signal was blinking at accelerated speed, then just quit. Now nothing, no noise, no clicking....any suggestions? Thanks

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ZJLimited
  • 17970 Answers

SOURCE: neither turn signal or hazard work, 15 amp fuse

The flasher is located in the Junction Block (under the dash, left of steering wheel. See diagram at very top of this page)...:

zjlimited_407.jpg__zjlimited_408.jpg

Check the position F4, 15 Amp (Lt. Blue) for Flasher, hazard switch (see Junction Block diagram above for location of turn signal Flasher relay - Mopar p/n 4686094).

Look at the end of the flasher relay with the prongs sticking out. There will be 2 plastic tabs holding it together. Break or bend these back. Pull out the insides. On one side will be all the components. On the other side will be solder joints. Get a magnifying glass and inspect these joints. One or two will probably have stress cracks. Just dab a little flux on this joint and heat it with a soldering iron until it melts back together. You may need to add just a little solder. Be sure to get the pins hot and not just the solder. They need a lot of heat. Slide the relay back into its cover, dab a little super glue or tape it back together, and you're ready to go.

Hope helps (remember to rate and commene this help).

Posted on Jan 06, 2011

  • 157 Answers

SOURCE: Turn signal and hazard lights

Most likely the cause of your problem is a flasher module. Usually it is found in the fuse box under the dash. But it can be on the back of the turning signal switch. If you are unsure, contact the service department of your manufacturer and ask them the location of the module. They will know immediately.

Posted on Feb 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fix signal lights


If the hazard flasher is working but the turn signals aren't, the problem is most likely either fuse A11 or the #2 relay in the trunk fuse block. However, if these check out, the problem could be either the turn/hazard switch assembly or the turn flasher module.

If both the turn signals and hazard flasher are not working, the most likely problem is the turn/hazard switch assembly.

May 03, 2015 | 1996 Cadillac DeVille

1 Answer

Hazard lights malfunction


YOU MIGHT HAVE A BURNT OUT RELAY IN FUSE COMPART UNDER YOU CARS HOOD CHECK THAT OUT THRU YOUR CARS MANUAL,IT WILL SHOW YOU WHICH RELAY IT IS?

May 24, 2013 | Cars & Trucks

1 Answer

No turn signal, hazard signals


OK YOU HAVE REPLACED RELAYS AND FUSES ARE GOOD.DOES THIS TRUCK HAVE A TRAILER WIRING HARNESS ADDED TO IT? HAVE YOU CHECKED/REPLACED THE MULTI-FUNCTION SWITCH?

Feb 22, 2013 | 1990 Ford F150

1 Answer

Rear lights not working on 2002 suzuki grand vitara


In the underdash fuse/relay box, the 15A TAIL fuse feeds power to the coil of headlight relay 2. When the combination switch is set to TAIL, the relay closes and the outer tail lamps light. In the same underdash fuse/relay box, the 20A STOP fuse feeds power to the brake light switch. When the brake pedal is pressed, the inner brake lamps light. The underdash fuse/relay box also contains the 10A TURN BACK fuse which feeds power to the hazard switch and the turn signal relay. Relay output is fed to the combination switch and turn signal power is applied to the selected middle tail light. The fourth fuse in the underdash fuse/relay box is the 15A HAZARD fuse which feeds power to the hazard switch and turn signal relay. When the hazard switch is set, the turn lamps on both sides begin flashing.

Sep 18, 2012 | 2002 Suzuki Grand Vitara

1 Answer

I have a 2006 GMC Envoy and the problem that i have is that all the signal lights stopped working including the hazard lights i checked all the fuses and all are find. What could it be? If somebody can...


{: ) If the IGN E fuse and the HAZARD fuse at the underhood fuseblock is okay, and the signal lamps wont light or flash at all, and assuming the wirings & connectors are also okay, it could be your turn signal multifunction switch or your turn signal hazard flasher module that is faulty.

Feb 26, 2011 | 2006 GMC Envoy

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Have hazard lights but no running or turn signals


sounds like you need a combo flasher assembly..located in fuse block inside vehicle under steering column..there may be a plastic cover under dash you have to remove to see fuse block..large black relay that plugs into fuse block..if you pick up a new one,you will see what it looks like..available at dodge dealer..combo flasher or drl/signal relay

Jun 11, 2009 | 1999 Dodge Caravan

1 Answer

Turn signals and hazards dont turn on


The turn signals run through the hazard switch, I have replaced hazard switches for this problem.

Apr 22, 2009 | 1996 Honda Accord

1 Answer

Signals don't signal


check fuse number 17 in fuse block if ok check bulbs <you said they turn on just don't flash so thats ok> the relay feeds power to the switch cluster but the flasher unit itself is built into the combo switch for turn signal/hazard switch

Mar 24, 2009 | 1994 Volkswagen Golf

2 Answers

Turn signals don't work


i have a similar problem but my left signal works, when i turn the right on it just does an annoying buzz sound. if you can think of any explination for such shinanogins help would be greatly appreciated

Nov 25, 2008 | 1989 GMC K1500

Not finding what you are looking for?
2001 Volkswagen Beetle Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...