Question about Chrysler 300C

Open Question

Location of oxygen sensor on chrysler 300 v8 2005 and how many their is to r eplace

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3600 Answers

SOURCE: oxygen sensor replacement

you need to rent an 02 sensor socket and use a ratchet and the socket to remove it, there are two on the exhaust pipe one before the cat, you can see it on the exhaust pipe and one after. normally the 1at one goes out. cost $75.00 please rate if helpful.

Posted on Aug 14, 2009

Testimonial: "it was very helpful! thanks"

Ad
66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

  • 184 Answers

SOURCE: BANK 2 SENSOR 1 WHERE IS IT LOCATED ON 02 CHRYSLER 300 M

That sensor is the one between the exhaust manifold and the catalytic converter (sensor #1). Bank 2 is the side of the engine that cylinder #1 is NOT on. Here is a diagram showing cylinder #1.

6468c66.gif

FYI, sensor #2 is the one behind (downstream) the catalytic converter.

Posted on Mar 25, 2009

  • 1 Answer

SOURCE: Code P0406

Where is the egr valve on my crystler 300?

Posted on Aug 17, 2009

  • 2 Answers

SOURCE: cooling fan switch/or sensor

The Coolant temp Sensor is located right under the top radiator hose (on the engine side), with a little black connector!, You might have to remove th etop hose to get to it with a deep socket and extension!.
Also Dont Forget to blled the coolant system by the bleeder valve uptop right near/above the coolant sensor!.(10MM Mini socket w/ extension IIRC!)

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I get code PO 135 Bank 1. where is this sensor located on a 2003 Chrysler Sebring lxi 3.0


Hi Russel,here's a link showing you your oxygen sensor,it's the second picture.It's screwed in right before that cat as you see. It's close to the firewall side.Repair Guides Components Systems Heated Oxygen Sensor AutoZone com Here's a link to a new one. Bosch Oxygen Sensor 15514 Read 1 Reviews on Bosch 15514

Dec 17, 2016 | Chrysler Cars & Trucks

2 Answers

Where is bank 1 sensor 2 located at on 2003 dodge stratus wit a 2.4 engine ?


    Dodge Chrysler - YouTube

    ? 2:54
    https://www.youtube.com/watch?v=vs2DuvehVGA
    Oct 31, 2013 - Uploaded by 1A Auto Parts
    I want to know about a Dodge Stratus 2002 sensor. ... I have a 05 Chrysler 300 2.7 engine with a fault code ... images for Where is bank 1 sensor 2 located at on ...


    More images for Where is bank 1 sensor 2 located at on 2003 dodge stratus with a 2.4 engine

    Where is bank 1 sensor 2 located at on 2003 dodge stratus wit

    www.fixya.com/cars/t26025690-bank_1_sensor_2_located_2003_dodge
    22 mins ago - SOURCE: check engine light is on...bank 1 sensor1 oxygen sensor. if u have one .... 2.7L dodge stratus/ #1 bank #2 sensor location? on 2004 Stratus. Oct 24 ... How can I set the timing on a 1996 dodge stratus 2.4l engine.

    P0137 02 Sensor Circuit Low Voltage - OBD-Codes.com


Dec 28, 2015 | Dodge Cars & Trucks

1 Answer

Where is the oxygen sensor on a chrysler 300 2005


http://www.300cforumz.com/showthread.php?t=58694


You will have to sign up as a forum member [free, quick and easy] in order to view the link to the online manual but I think you'll find what you need there-

Jan 15, 2014 | 2005 Chrysler 300

1 Answer

0152 coed


P0152 P0152 - O2 Sensor Circuit High Voltage Bank 2 Sensor 1Possible causes - Faulty Front Heated Oxygen Sensor Bank 2
- Intake air leaks may be faulty
- Exhaust gas leaks
- Front Heated Oxygen Sensor Bank 2 harness is open or shorted
- Front Heated Oxygen Sensor Bank 2 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
eplacing the Front Heated Oxygen Sensor Bank 2 usually takes care of the problem
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- High Fuel Consumption
- Excessive Smoke from Exhaust P0152 Description The front heated oxygen sensor (or O2 sensor 1) is placed into the exhaust manifold. It detects the amount of oxygen in the exhaust gas compared to the outside air. The heated oxygen sensor 1 has a closed-end tube made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. The heated oxygen sensor 1 signal is sent to the Engine Control Module (ECM). The ECM adjusts the injection pulse duration to achieve the ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical change from 1V to 0V.

Mar 19, 2013 | 2005 Dodge Ram 1500

1 Answer

It will be very much appreciated if you could send me the information about how to replace the O2 sensors on a 1998 chrysler sebring convertible.


Hello, Eventually your Chrysler Sebring's oxygen sensor will go bad and need to be replaced. The oxygen sensor regulates the oxygen-to-fuel ratio in your vehicle. It also controls your gas mileage. It senses when more or less oxygen needs to be pumped into the fuel lines. If it fails, your Sebring will run poorly and won't get very good gas mileage. Knowing how to change it yourself can save your money. Here are the instruction to change o2 sensors.
Locate your Sebring's oxygen sensor on the pre-catalytic converter. This is located near the front right wheel well of your vehicle. Apply some anti-seize paste to the threads of the new oxygen sensor. Be careful not to get any of the paste on the sensor itself, or it will be ruined. This makes for easy removal of the sensor next time.Remove the old oxygen sensor, using the 7/8-inch wrench. Find the stock sensor wire near the engine-loop lift. This will be by the firewall of your Chrysler Sebring. Splice the stock sensor wire and connect it to the new oxygen sensor's wire, using crimp connectors.Remove the large air-intake pipe that runs from the air box to the rear turbo. Then remove the two smaller air pipes that run from the air box to the blowoff valves. This will give you access to the oxygen sensor. Soak the old oxygen sensor in WD-40 to loosen it. Screw in the sensor by hand. Use the wrench to fully tighten the oxygen sensor so it cannot be removed by hand. Replace the air pipes to the correct valves again.

  • Rate me if you like my answer..


    Thanks

  • May 20, 2011 | 1998 Chrysler Sebring

    2 Answers

    How many oxygen sensors does a 2001 Chrysler Sebring have with the 2.7 liter engine


    It has two sensors...

    Check the below link for pictures

    http://www.fixya.com/cars/t2915557-many_oxygen_sensors_in_2001_chrysler

    Aug 30, 2010 | 2001 Chrysler Sebring

    1 Answer

    Location of downstream oxygen sensors


    The downstream o2 sensor is located behind the catalytic converter.

    Feb 02, 2010 | 2002 Chrysler Sebring

    2 Answers

    How many oxygen sensors in a 2001 chrysler sebring 3.0


    17c3292.jpg

    Fig. Heated Oxygen (HO2S) location (sensor 1)-2.4L engine

    db6f426.jpg

    Fig. Heated Oxygen (HO2S) location (sensor 2)-2.4L engine

    99e413c.jpg

    Fig. Heated Oxygen (HO2S) location (bank 1, sensor 2) (bank 2, sensor 2)-2.7L engine

    e2a250f.jpg

    Fig. Heated Oxygen (HO2S) location (bank 2, sensor 1)-2.7L engine

    I hope help you with this (rated this help). Good luck.

    Sep 09, 2009 | 2001 Chrysler Sebring

    1 Answer

    2001 crysler 300 M


    O2 sensor is located forward of the catalytic converter. You will need a 22mm wrench or O2 sensor socket to remove and reinstall.

    Dec 25, 2008 | 2001 Chrysler 300M

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    665 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8269 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...