Question about 2000 Ford F150 Flareside SuperCab

1 Answer

Oem remote start doesent work on my 2000 f150 checked the fuses both r ok and also checked the hood switch it seems ok where do i go from there

Posted by on

  • 4 more comments 
  • Steve S
    Steve S Nov 09, 2010

    What is happening when you try to use the RMST ?

  • birdstar2004 Nov 10, 2010

    really nothing at all heard a click in a relay or somthing once but otherwise there is no reaction at all new battery put in the remote switch didnt help either

  • Steve S
    Steve S Nov 11, 2010

    Do you get a horn beep code ( i.e. 2 beeps ) or the lights flash. Asking to see if it is a tach mode error How did you check the hood switch ?

  • birdstar2004 Nov 11, 2010

    held it down by hand and tied the remote didnt know any other way and there was no lights and no beep

  • birdstar2004 Nov 11, 2010

    held it down by hand and tied the remote didnt know any other way and there was no lights and no beep

  • birdstar2004 Nov 11, 2010

    held it down by hand and tied the remote didnt know any other way and there was no lights and no beep

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 984 Answers

The hood switch should have produced an error of some kind ( at the very least flash the parking lamps ).
The hood switch is to ground, if you meter ( ohms or continuity ) from ground to the wire leaving the hood switch one direction you should have an open the other you should have < 100 ohms ).
I suspect the hood switch is OK, if the hood is open the OEM remote start would honk the horn 2 times.

If when you press the remote start, the ignition turns on then off ( cluster powers up ) check the Violet & Violet w/ red stripe wires to make sure they are still connected. and the A-4 & B-2 wires ( on the RMST unit ) that they have + VDC.
Did the unit operate correctly at one time ?
- Just verifying it is not a programming issue with it.

Posted on Nov 13, 2010

  • birdstar2004 Nov 17, 2010

    tried this out actually im not getting anything at all no horn no lights at all its like my remote start not sending or recieving im not sure how it works antenna is lit up but noticed this morning it was out till about ten minutes after i started the truck up

  • Steve S
    Steve S Nov 17, 2010

    Try checking the hood switch to ground. One direction is ~ 0 ohms to ground, the other will be an open.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After jump starting 2006 Z4 BMW headlight low beams don't work checked fuses in glove compartment and under hood all seemed to be ok is there a relay, what do i do now


If the lights are switched then the switch controls a rely all lights are switched on bmw. Can use fog lights temporarily. Find rely test with continuity meter when on, disconnect lights first, then turn on lights switch, check for 12v at light bulb terms, if 12v then bulbs bad, if not relay is bad, test with continuity meter, rely should read 0 ohms when lights switched on, infinite open circuit when switched off. If lights work in manual switch pos then solar sensor bad.

Dec 05, 2012 | 2006 BMW Z4 Roadster

1 Answer

Battery light stays on 2000 f150


This could only be a few things, so I would recommend that you start with the fuses inside the cab, and under the hood, to ensure that they are good. If they check out, then have the alternator tested.

Mar 22, 2011 | 2000 Ford F150 Flareside SuperCab

1 Answer

Hello!!! I am having trouble. This has happened one time before and I fixd it but I cant remember how in the heck I did it. Here is the prob...The doors will not lock or unlock by the buttons or the...


check the fuses to the CSM ( Central Security Module ) .

CJB ( aka Central Junction Box, cab fuse panel ) Fuse # 15 & 29
15 is the BPP ( Brake Pedal Position ) Switch, so that should be fine, unless you cannot get the truck out of park while running and the brake lamps don't work.
29 is the fuse to the CSM ( hot in start or run key positions ).

BJB ( aka Battery Junction Box, Engine Compartment fuse panel ) Fuse # 115 or 8. 115 is for the Supercrew body style and 8 is for the standard cab & SuperCab configuration.

This is for a build date after 2-OCT-2000 ( 2001 MY ).
Build date before 2-OCT-2000, the CSM is a RAP ( Remote Anti-theft Personality ), looks the same, same functions, but is not pin for pin compatible.
Fuses for this are CJB Fuse #8 and 15 and BJB Fuse #4.

With the CSM / RAP installed, the power door locks are controlled by the CSM/RAP, without the RKE ( Remote Keyless Entry ) installed, they are normal power door locks ( switch to the door lock direct ).

Worth a start checking the CSM / RAP fuse

Nov 18, 2009 | 2001 Ford F150 Styleside SuperCrew

4 Answers

I have a '98 Ford F 150 and the power door locks will lock but will not unlock. Do you have a wiring diagram that will help me troubleshoot the problem or is this a common problem with Ford that someone...


ck if either pass or driver switches will work. the lock actuators are common to be bad, but, if they lock but wont unlock more likely a switch problem.

Sep 16, 2009 | 1998 Ford F150 Regular Cab

1 Answer

BRAKELIGHTS WONT WORK FUSES CHECK GOOD BULBS CHECK GOOD AND REPLACED BRAKE PEDAL SWITCH THIS IS ON A 2000 F150 W/5.4 ENGINE


recheck wires to brake pedal switch been known to break off ? if they checkout ok look toward possible turn signal switch problems?

Aug 26, 2009 | 2000 Ford F150 Flareside SuperCab

1 Answer

No stop and turn lights for trailer hookup f150 1997


Check the fuses under the hood near the brake booster. The trailer fuse are usually in one of those fuse/relay boxes. Good luck.

Jul 01, 2009 | 1997 Ford F150 Regular Cab

2 Answers

Just bought an 03' f150. my map lights inside work, but the dome and cargo bed lights do not. also cant find a diagram of the fuse panel anywhere. Thank You


have u check the bulbs?.... i would try to see if they ok remove em an check for power going to those locations, activate ur switches an see if you get any power may just be burned bulbs..... if the fuses seem to be OK

May 28, 2009 | 2003 Ford F150 Regular Cab

1 Answer

2002 F150 brake/turn signal


if u checked all the fuse's both in the cab and under hood and the wiring harness at rear of truck for any damage, I suspect the turn signal switch is defective.

Mar 05, 2009 | 2004 Ford F150

2 Answers

2000 F150 won't start


cheack ,fuse no 30, in fuse box Located inside the truck by the hood opner

Nov 17, 2008 | 2000 Ford F150 Flareside SuperCab

2 Answers

1989 honda accord ignition not working


need more info like the start does not work ?
or it doesent click on third position?

Jul 05, 2008 | 1989 Honda Accord 4 Door

Not finding what you are looking for?
2000 Ford F150 Flareside SuperCab Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...