Question about 1993 Nissan Altima

1 Answer

Torque specs Replacing knock sensor but can't find torque specs. Can anyone help?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 61,292 Answers

13-15 foot pounds.

Posted on Sep 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can anyone.tell me the Torqe specs for a 2004 or cruiser


Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

Jan 18, 2016 | Cars & Trucks

1 Answer

Where can I find plenum torque specs for 2004 chrysler 300m 3.5L? Replacing cam shaft position sensor


Depending on Your vehicle engine model, Vin #'s K, M, with a 3.5 ltr engine, the torque spec are 109 in lbs.

If the engine Vin # is a V, then the torque 113 in lbs

Jun 13, 2011 | 2004 Chrysler 300M

1 Answer

Trying to find timing specs and engine torque specs for a 1998 Acura TL 3.2. Replacing the head gasket and knock sensors, please help...


Autozone and oreilly and basically all of the parts stores have free online specs and settings to look up.

Nov 02, 2010 | 1998 Acura TL

1 Answer

Where are the knock sensors located on a 2002 chevy silverado 2500hd 6.0 engine?


Knock sensors as a rule of thumb are positioned right beside a piston on the the block. It should be on the opposite side of the exhaust system. A knock sensor is actually a sensitive microphone or listening device. It listens to a piston performance under load. If it hears a knocking or pinging sound it will ****** the ignition timing and advance it again when condition changes. It would have a securing bolt in the middle which torqued to a certain spec and a single wire harness.

Mar 14, 2010 | 2002 Chevrolet Silverado 2500HD

2 Answers

Steps to replace a knock Sensors?


I had to do this last summer. First I went to Advanced Auto. They
read the code for me. One of them was bad, but I went ahead and
replaced both. I purchased a manual for the steps, two knock sensors
and a gasket set. About 170 dollars total. You will also need a torq
wrench in inch pounds. Take your time, keep it clean. Make sure
you clean the manifold and engine head surfaces where the gasket
seats. Use a non metallic scraper, and if need be solvent to loosen
any old gasket material. I found that laying saturated rags on the
head surface and leaving them set a few hours helped the most.
You can also get the steps and torque specs from either Advance
auto or Auto Zone(then you don't need the manual).
Use patience when tightening the manifold bolts, you should
torque them in the sequence given(in the manual or online) and
you have to do it twice, first time at half torque, then the second at
full torque. If you over tighten you can crack the manifold.
Good luck
Art LeDoux, Stillman Valley Illinois

Dec 24, 2009 | 2001 Chevrolet Suburban

1 Answer

Knock sensor dont work for 2005 dodge durango


this problem is very seldom the knock sensor, it can be the harness connector at the sensor or the engine has excessive knock which will set a code, u did not mention the particular code so hard to say, the location of the knock sensor is the lower section of the engine block, it is screwed into what would normally be a block drain plug, if u replace it u need to torque it to whatever the factory spec is or it can cause it throw another code..

May 29, 2009 | Dodge Durango Cars & Trucks

1 Answer

2005 Dodge Durango knock sensor problems


I really doubt the knock sensor is the problem, check the connector 1st for water intrusion or oil, if u do replace it then u must torque it to the proper spec into the cooling system jacket of the block or it will set another code.

Mar 11, 2009 | 2005 Dodge Durango

1 Answer

1999 Saab 9-5 oil pan torque spec


they should be torqued with a 3/8 torque ratchet to 30 inch pounds.

Mar 06, 2009 | 1999 Saab 9-5

Not finding what you are looking for?
1993 Nissan Altima Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...