Question about 2003 Mazda MPV

1 Answer

Cannot open doors with key switch - 2003 Mazda MPV

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 528 Answers

Try replacing the battery in the key fob remote after checking the fuse panel for a blown fuse. Refer to your manual for panel location. Also check the manual for a relay - you might also have a bad relay, but i would do the battery first as they are usually less than $5.00 usd.

Posted on Nov 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I lock a renault megane 56 plate without the key card as it is not working


Locking/Unlocking the doors from the outside
This is done using the RENAULT Card; see the "RENAULT Card" information in Section 1.
In certain cases, the RENAULT card may not work:
- if the RENAULT card battery is weak, flat, etc.
- if equipment operating on the same frequency as the card (mobile phones, etc.) is used;
- vehicle located in a high electromagnetic radiation zone.
It is then possible:
- to use the key integrated into the card to unlock the front left-hand door;
- to lock each of the doors manually;
- to use the interior door locking/unlocking control (refer to the following pages).
Using the key integrated in the RENAULT card
Insert key 1 into the lock in the driver's door and lock or unlock. Locking the doors manually
Turn screw 2 with the door open (using the end of the key) and close the door.
This means that the doors are then locked from the outside.
The doors may then only be opened from the inside or by using the key in the front left-hand door. Interior locking/unlocking door control
Switch 3 controls the doors, boot and, depending on the vehicle, the fuel filler flap simultaneously.
If a door or the tailgate is open or not closed properly, the doors and tailgate lock/unlock quickly.
If you need to transport objects with the boot open, the other opening elements can still be locked: with the engine stopped, press switch 3 for more than five seconds to lock the other opening elements.
Locking the doors without the RENAULT card
For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc.
With the engine switched off and an opening element (door or boot) open, press and hold switch 3 for more than five seconds.
When the door is closed, all the doors and the tailgate will be locked.
Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle's access zone or using the key integrated in the RENAULT card.
Door and tailgate status indicator
With the ignition on, the warning light integrated in switch 3 informs you of the locking status of the opening elements:
- indicator light on, the doors and tailgate are locked,
- indicator light off, the doors and tailgate are unlocked.
When you lock the doors, the indicator light remains lit and then goes out.

Dec 12, 2015 | Renault Megane Cars & Trucks

1 Answer

2007 yaris door wont lock when driver door is open


sounds like the ignition lock is worn out.

Mar 01, 2017 | 2007 Toyota Yaris 1.4

1 Answer

The door ajar beeping comes on anytime a door is open, whether or not a key is in the ignition.


The light and the beeping are two differant things. Headlight switch on? Or the switch were the key gos may think the key is still in the switch.

May 18, 2012 | 2002 BMW 3 Series

1 Answer

How do you program a replacement key for a lexus es 330 2004


Here are the instructions from the factory manual. They must be followed exactly.
2004 ES330
1. Driver's door open, all other doors closed, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.

2. Within 40 seconds:
Close and open driver's door twice.
Insert and remove the key from the ignition switch.

3. Within 40 seconds:
Close and open driver's door twice.
Insert the key into the ignition switch and close the driver's door.

4. Switch ignition ON and OFF:
A. Once to program a key remote transmitter code whilst retaining the original codes.
B. Twice to program a key remote transmitter code whilst erasing the original codes.
C. Three times to check how many key remote transmitters are currently registered.
D. Five times to erase all registered codes.

5. Remove key from ignition switch. System should now lock and unlock vehicle
once, twice or five times depending which mode has been selected. One to four
times, slowly, to indicate number of key remote transmitters registered.

6. Within 40 seconds:
Press and hold LOCK and UNLOCK buttons simultaneously for 1.5 seconds.
Within 3 seconds: Press any key remote transmitter button.

System should now lock and unlock vehicle once to confirm registration or twice
to indicate registration has failed.

7. Within 40 seconds:
To program additional remotes repeat step 60 now on each additional
remote you want programmed.

8. To exit programming mode open driver's door or insert key into ignition.
9. Step out of car with remote(s) in hand and test remote(s).

Nov 01, 2011 | 2004 Lexus ES 330

2 Answers

With the car off, when I simply put my key into the ignition the chime for the door being open goes off. With or without the key, the dome light stays on as if the door was open when the car is off or...


It sounds like a door ajar switch is broken. The door switches are located in the door on the latch mechanism. To get to it you will need to remove the door trim panel to gain access to the door latch.

The switch is available for around $20 - autozone part number SW1979 or SW3688

Mar 19, 2011 | 2003 Ford Mustang

1 Answer

Remote got wet in salt water. Had battery changed


Programming
When
Key added or replaced. System malfunction.
How
Driver's door open and key removed from ignition switch. Insert key into ignition switch, then remove it. Within 5 seconds: Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch. Close driver's door. Switch ignition ON and OFF once to program a new key code whilst retaining the original codes or twice to program a new key code whilst erasing the original codes. Remove key. System should now lock and unlock vehicle, once or twice depending which mode has been selected. Carry out the following button procedure within 40 seconds: Press key lock or unlock button once. Within 3 seconds: Press same key lock or unlock button once. System should now lock and unlock vehicle.
NOTE: If system locks and unlocks vehicle twice, programming procedure has not been completed. Repeat button procedure.
If required repeat button procedure to program remaining keys.
NOTE: To exit programming mode: Open driver's door. NOTE: A maximum of 4 keys can be programmed

This will work providing printed circuit is not damaged in remote

Jul 20, 2010 | 2004 Toyota Camry

1 Answer

I just bought a 1996 jeep grand cherokee larado, I locked the doo while inside with electric lock switch on door. I then opened the door with the handle. the alarm went off which I did not know it had. I...


lock with key,electric door lock button,or remote and alarm will set. to disarm you have to use the key or remote to open it.the reason it woulnt disarm from drivers door is either the door lock cylinder switch is broken or the wire to it in the rubber boot that connects the door and the body is broken.
the remotes are cheap and programing is easy,procedure in owners manuel something like lock drive door with elkect. lock switch with door open then push and hold unlock untill doors unlock then turn key off.you may have to fix that drive door lock cyl.switch first though mabee not dont know for sure

Mar 22, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Key on engine running trouble code 55


Warning Chime Systems The generic electronic module (GEM) will sound the following warnings:
  • key-in-ignition warning
  • safety belt warning
  • headlamp switch ON warning
  • door ajar warning
------------------------------------------------------------------------------------------------
Headlamp Switch On Warning The generic electronic module (GEM) sounds when the driver door is opened while the headlamp switch (11654) is in the PARK or HEAD position, and continues to sound at a rate of 4 chimes per second until the headlamp switch is turned off or the driver door is closed.
  • When the headlamp switch is in the PARK or HEAD position, power is supplied through Circuit 293 (O/R) to the GEM.
  • When the driver door is open, the driver door open warning lamp switch (10B997)is closed and ground is supplied to the generic electronic module (GEM).
A delayed headlamps on repetitive chime will sound for a period of three seconds beginning twenty seconds after the key is turned to OFF, LOCK or ACC, the headlamp switch is in the PARK or HEAD position, and the driver door is closed. Delayed headlamps on is terminated by opening and closing the driver door again.
---------------------------------------------------------------------------------------
Door/Liftgate Ajar Warning The door/liftgate ajar warning functions as follows:
  • The generic electronic module (GEM) sounds a warning tone for one second when any vehicle door, liftgate window or the liftgate is ajar without any other door already open and the ignition switch is in the RUN position.
  • Power is then supplied through Circuit 627 (BK/O) to the door ajar warning indicator lamp which remains illuminated until all doors are closed or the ignition switch is no longer in the RUN position.
----------------------------------------------------------------------------------------------
Key-in-Ignition Warning The generic electronic module (GEM) sounds when the LH front door is opened with the key in the ignition switch and continues to sound until the key is removed or the door is closed.
  • When the key is in the ignition switch, the ignition key warning switch terminal and wire (11A128) is closed and ground is supplied through Circuit 158 (BK/PK) to the generic electronic module (GEM).
  • When the LH front door is open, the LH front door open warning lamp switch (10B997) closes and ground is supplied through Circuit 57 (BK) to the generic electronic module (GEM).
-------------------------------------------------------------------------------------
Safety Belt Warning When the ignition switch is turned to RUN or START from the OFF or ACC position and remains in RUN or START, the chime will sound for six seconds or until the safety belt is buckled. The safety belt warning indicator lamp (10C859) will turn on for 60 seconds, or until the LH front safety belt is fastened. Both the chime and lamp activate at the same time. If the safety belt is buckled when the ignition key is turned to RUN or START from OFF or ACC, the lamp will prove out for two seconds, but chime will not be activated. Any time the key is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Feb 25, 2009 | 1999 Ford Taurus

1 Answer

Program my remote


Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entrymag-glass_10x10.gif, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.
  • Open the driver's door. Remove the key from the ignition switch.
  • (Complete these steps within 40 seconds)
    1. Insert the key into and remove it from the ignition switch 2 times.
      (IN - OUT - IN - OUT)
    2. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    3. Insert the key into and remove it from the ignition switch 1 time.
      (IN - OUT)
    4. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    5. Insert the key into the ignition switch and leave it in.
    6. Close the driver's door.
    7. Turn the key from LOCK to ON 4 times, ending at LOCK
      (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
    8. Wait for the locks to stop, then remove the key from the ignition switch.
  • On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
    1. [For all doors unlock] press and release the UNLOCK button.
    2. [For driver door unlock] press and release the LOCK button.
  • Open the driver's door. The programming is complete. If programming did not occur, start over.

Jan 13, 2009 | 2001 Toyota Tacoma

Not finding what you are looking for?
2003 Mazda MPV Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...