Question about 1997 GMC Yukon

1 Answer

1997 GMC Yukon 4WD with 5.7L Auto - Belongs to Father. Initial Concerns with Rough Idling, and High Idle RPM. Vehicle will drive away at 15km/h as soon as brake released. Vehicle Creeps ahead at traffic lights on Dry Pavement, or will lock up front tires, and skid ahead on ice. Work done so far: New Plugs, Wires, Rotor and Cap. Underhood check for Vacuum Leaks - Hoses, Intake Manifold, Throttle Body etc. Full KOEO and KOER Diagnostics with Innova 3120 CanOBDII and OBDI Scan Tool. Full KOEO and KOER with MAC TaskMaster. Full KOEO and KOER with Snap-On SolusPro According to ALL the Scan Tools, all the system components are operating correctly, but I am getting the following codes: P0300 Random Misfire Detected P0507 Idle Control System RPM Higher than Expected. Any ideas where to go next? I can listen around engine bar with Stethescope to try to find leaks, or rig up a Crude Propane Enrichment if you think that a Vacuum leak may be causing one or more of the issues. Thanks in Advance.

Posted by on

  • 1 more comment 
  • cheap repair Nov 08, 2010

    start by cleaning the throttle bore. deposits may be causing the throttle valve to not close fully. Same for the IAC control valve, clean valve and mounting bore.

  • black_wolf_7 Nov 08, 2010

    Thank you for that - Forgot to mention that father already removed Throttle Body and cleaned the bores, as well as IAC Valve and bore.

    I was originally going to go after the injectors and poppet valves as a source of the rough idling, but this P0507 has me concerned. Didn't realize how bad it was until I cleared the DTC's and took it for a 1/2 hour drive to town to re-learn the driving.... WOW - Disturbing.

    Using the SolusPro, I was able to cycle the IAC and EGR systems (among others) and all components checked out fine.

    This whole situation is a little frustrating for me - I was a mechanic at a GM Dealership in the early 90's but I left the trade years before this vehicle (Or this style of Fuel Injection) was built, so I am trying to "Learn" about the Central SFI as I go... Dad's older truck - a '92 C1500 with the TBI was MUCH easier to play with... At least on THAT one I could disconnect the Spark Advance and check the base timing, but this thing - NADA.

  • black_wolf_7 Apr 24, 2011

    Most certainly - Internal Vacuum Leak. The intake manifold gaskets are only pinned on the ends, and over time, and with heat cycling, they sagged until the seal was compromised on Cylinder #6, causing the engine to draw in air from the lifter valley. I pulled the intake manifold (upper and lower together as one piece) and replaced the intake manifold gaskets. Put it all back together, and cleared all the codes - It has ran like a top ever since. Good Luck.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a 97 yukon with a rough idle, can you ntell me what you have found out.

Posted on Apr 23, 2011

  • black_wolf_7 Apr 24, 2011

    Most Certainly - Internal Vacuum Leak. The intake manifold gaskets are only pinned at the ends, so with time and heat cycling, they sag until the intake runner seal is compromised. Im my case, it was Cylinder #6. I pulled the intake manifold, cleaned up the heads, replaced the gaskets, and put it all back together. After clearing the codes, it has ran like a top ever since. Hope it helps.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999dodge intrepid 2.7 lite idle low


Car Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html
------------


It can be issue with IAC( idle air control valve) causing the problem.


There are many other possibilities causing these idle issues. Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----

Ford Expedition IAC valve replacing

http://technoanswers.blogspot.com/2012/12/ford-expedition-iac-valve-replacing.html

Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------

Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------

1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------

Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------

GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------

1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------

Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------

Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------

High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------

Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------

Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

Dec 12, 2012 | 1999 Dodge Intrepid

1 Answer

I have a 98 Malibu when I turn it over it runs rough then dies


It can be issue with IAC( idle air control valve) causing the problem.


There are many other possibilities causing these idle issues. Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----

Ford Expedition IAC valve replacing

http://technoanswers.blogspot.com/2012/12/ford-expedition-iac-valve-replacing.html

Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------

Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------

1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------

Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------

GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------

1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------

Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------

Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------

High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------

Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------

Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

Dec 07, 2012 | Cars & Trucks

1 Answer

1993 1500 truck 5.0 high HC at idle


It can be issue with IAC( idle air control valve) causing the problem.


There are many other possibilities causing these idle issues. Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----

Ford Expedition IAC valve replacing

http://technoanswers.blogspot.com/2012/12/ford-expedition-iac-valve-replacing.html

Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------

Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------

1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------

Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------

Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms

http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------

Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------

GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------

1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------

Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------

Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------

High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------

Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------

Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------

While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

Dec 06, 2012 | 1999 Chevrolet Silverado 1500

2 Answers

92 dodge 1500 pick up 360 v8 automatic Starts, runs but hesitates, low power code 37 on diagnostic readour


Code 37 is torque converter clutch solenoid failure. Transmission wont shift in and out of overdrive.

Nov 28, 2012 | Dodge Cars & Trucks

1 Answer

Ford Taurus idle missing


It can be issue with IAC( idle air control valve) causing the problem.


There are many other possibilities causing these idle issues.Engine idles rough.

There are few help links with solutions to troubleshoot such idle issues.

I suggest you refer the link below and follow its troubleshooting details:------

Click the link below:-----
Bad miss at idle? http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------
Stumbling and stalling at idle after engine rebuild?

http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------
1999 Ford F-150 Idles rough and quits when gas pedal is pressed less?

http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

---------
Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------
Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms
http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html

----------
Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------
GMC Sonoma Stalls and idles low

http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html

--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------
1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------
Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------
Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------

High Idle Problem

http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html

-------
While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------
Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------
High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------
Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------
Rough idle, staling and Erratic shifting?

http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html

-----------
While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------

These details will help.

Thanks.

Nov 24, 2012 | 2001 Ford Taurus

2 Answers

REPLACED THE EGR VACUUM SOLENOID NOW IDLES RUFF AND RPM GO UP AND DOWN AT IDLE


It can be issue with IAC( idle air control valve) causing the problem.

There are many other possibilities causing these idle issues.Engine idles rough.There are few help links with solutions to troubleshoot such idle issues.
I suggest you refer the link below and follow its troubleshooting details:------Click the link below:-----Bad miss at idle? http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html
-----------
Stumbling and stalling at idle after engine rebuild? http://schematicsdiagram.blogspot.in/2012/03/stumbling-and-stalling-at-idle-after.html

------------
1999 Ford F-150 Idles rough and quits when gas pedal is pressed less? http://technoanswers.blogspot.in/2012/01/1999-ford-f-150-idles-rough-and-quits.html

--------- Engine stumbles coming off idle when warm?

http://repairhelpcenter.blogspot.com/2012/01/engine-stumbles-coming-off-idle-when.html

------------------
Erratic idle on car?

http://schematicsdiagram.blogspot.com/2011/12/erratic-idle-on-car.html

-----------


Cold start problem and vehicle shudder around 2500 to 3500 rpms
http://repairhelpcenter.blogspot.com/2012/10/cold-start-problem-and-vehicle-shudder.html
---------- Low idle when cold out side?

http://repairhelpcenter.blogspot.com/2011/12/low-idle-when-cold-out-side.html

-----------


GMC Sonoma Stalls and idles low http://technoanswers.blogspot.com/2012/10/gmc-sonoma-stalls-and-idles-low.html
--------


GMC Idle Air Control (IAC) Valve Replacing?

http://schematicsdiagram.blogspot.com/2011/12/gmc-idle-air-control-iac-valve.html

-------------
1996 Camry intermittent engine failure while idle?

http://repairhelpcenter.blogspot.com/2011/10/1996-camry-intermittent-engine-failure.html

------------
Engine quits at idle?

http://repairhelpcenter.blogspot.com/2011/10/engine-quits-at-idle.html

-----------
Car overheats and Air blows hot at idle?

http://howtobyme.blogspot.com/2011/11/car-overheats-and-air-blows-hot-at-idle.html

---------


High Idle Problem
http://repairhelpcenter.blogspot.com/2012/10/high-idle-problem.html
-------


While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

---------
Idle flair is noticed on car? Rough idle? car will not idle? Erratic idle speed?

http://technoanswers.blogspot.in/2012/02/idle-flair-is-noticed-on-car-rough-idle.html

--------
High rpm in neutral? Inconsistant high RPM in neutral?

http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html

-------
Vehicle stumbling at idle and shows code 54?

http://schematicsdiagram.blogspot.in/2012/03/vehicle-stumbling-at-idle-and-shows.html

----------
Rough idle, staling and Erratic shifting? http://technoanswers.blogspot.in/2012/03/rough-idlestaling-and-erratic-shifting.html
-----------While stop engine idles like cylinder missing? http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html
---------These details will help.Thanks.

Nov 23, 2012 | 2001 Ford Escape

1 Answer

My 93 gmc yukon is idling high and shifting rough but i am guessing because it is idling anywhere from 1600-2000 rpm in park and 1000-1100 in gear. i had changed the throttle position sensor and idle air...


This is the IAC Idle AIR CONTROL , Located on the Pass Side if throttle Body Replace This and Your Problem WILL GO AWAY Seen this Over 10-15 Times With this Same Vehicle

Aug 19, 2010 | GMC Yukon Cars & Trucks

1 Answer

Rough idle / varying oil pressure when accelerating


Ok not to keen on newer vehicles actually prefer the carburated ones, but oil pressure is supposed increase on your gauge when accelerating. If it wasn't going up before and just staying at 40 the needle might have been stuck. But idle should be 40 lbs and when you work the moter (reving or driving down the road) the guage should show an increase for every 1000 rpm above idle. Second if you can get a hand held scanner (bought mine off ebay for $30) check for any codes in your computer you will probably find that you either have a bank running wrong or some other sensor that needs to be changed. I'd go with getting my own scanner it saves alot of money and time, garages make their money here.

Jan 03, 2009 | 2005 GMC Yukon

Not finding what you are looking for?
1997 GMC Yukon Logo

596 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...