Question about 1999 Mercury Sable

2 Answers

EGR DP sensor location on a 1999 mercury sable 3.0 engine

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 5,763 Answers

This sensor delta pressure feedback sensor for the egr is located on the top right side of the intake manifold, heres a diagram that will also help in locating this sensor, hope this is helpful. EGR DP sensor  location on a 1999 mercury sable - johnjohn2_12.gif

Posted on Nov 07, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I look for the egr sensor i cannot find it

Posted on Sep 28, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1994 Mercury Sable 3.8L


The car's wiring can be tested in the normal fashion (see our article on Automotive Circuit Testing here), and all vacuum lines can be checked easily for cracks, leaks and correct routing. the easiest way to test the 3 remaining components: the EGR valve, EGR vacuum regulator and DPFE sensor (or similar flow sensor). So if you have a scan tool hook it up and let's go, if not read on and we'll get around that too!

Oct 22, 2008 | 1994 Mercury Sable

2 Answers

Check engine light code p1400


The code is for differential pressure feedback sensor circuit low voltage detected. The DPFE sensor is used to measure pressure in and out of the EGR valve.
The sensor would need to be checked with a volt meter.

Jul 24, 2012 | 1999 Mercury Sable

2 Answers

1999 mercury sable engine code p1744,p0401. Failed e check. EGR looks new, replaced egr solenoid then cleared codes. what more can i do about the p0401 code and the p1744 code Thanks


for p0401:
In fixing this code, it is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open.
Clean out the EGR valve and/or tubing to remove deposits.
Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model).
Replace the DPFE sensor (with a good quality / OEM one).
Replace the EGR valve.

Jul 08, 2011 | 1999 Mercury Sable

2 Answers

This is the code number after testing for the check engine light P0401. Also , the exhaust gas recirculation flow is insufficient.


More than likely you have a faulty EGR Valve Pressure Sensor, especially if your EGR Valve Pressure Sensor is the original metal type. The new sensor is made of plastic and doesn't corrode like the old design. This sensor is located on the Intake Manifold.

pctech1_40.jpg

Here is the sensor: http://www.autozone.com/autozone/parts/2001-Mercury-Sable/EGR-Valve-Pressure-Sensor/_/N-jfkhrZ93y2i

It is also possible that the EGR Valve has a clogged port, but this is less likely.

Mar 15, 2011 | 2001 Mercury Sable

1 Answer

1999 Mercury Sable 24v OHC engine, starts normal but when engine begins to idle it runs rough and dies


this is a difficult one..
check for vacuum leaks by possibly a visual inspection and then spraying starting fluid around hoses , intake and so on..if any change, you might have found a vacuum leak/bad gasket.
otherwise, DO clean the Idle Air Control Valve 1st.
then check and clean EGR valve next..

Sep 30, 2010 | 1999 Mercury Sable

1 Answer

Obd2 scanner code reader indicated a p0401 problem with my 1999 mercury sable. What could be wrong. According to the handbook that is given with the scanner p0401 is an egr with insufficient flow.


your egr valve may be bad or you mite be just clogged. take it off and see if there is any deris in egr vavle or the hole on to mounting service if so clean out. if not replace the egr valve.

Nov 16, 2009 | 1999 Mercury Sable

1 Answer

EGR Sensor/valve replacement


The EGR is a three part series; the valve, soleniod, and sensor. They are fairly easy to change, a few hours with a buddy. They are located on the top back, center of the engine. Take a look you will see something that is small and cylinder like with a wire connected to the top, that is the vavle. I would replace all three at once as they are all together and you have to take of one to take of the others. The total price will cost you about $250 in parts. However, you must know your engine type on the Sable/Tarus as the parts are different per engine.

Apr 20, 2009 | 2002 Mercury Sable

2 Answers

DPFE Sensor with codes PO401 And PO402


The DPFE is located near the EGR valve, it has 2 very thick silicone rubber hoses connected to it that come off the exhaust. It is rectangular and about 1/2 the size of a pack of smokes

Nov 12, 2008 | 2001 Mercury Sable

Not finding what you are looking for?
1999 Mercury Sable Logo

2,308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...