Question about 1998 Mercury Sable

Open Question

How to replace a 1998 mercury sable Coolant Temperature Sensor

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 375 Answers

SOURCE: Replace coolant temperature sensor

hey
Look at the motor front of van located right side of motor twards rear below head ,disconnect wired pulls off ,wrench it out counter clockwise, install new replace wire.
your responsibility if u filing any concern on doing that jump to the local garage--fast and cheap.


Posted on Jun 29, 2008

  • 8 Answers

SOURCE: rear brakes on 1998 mercury sable

I've done it and hated every minute of it.

Get a quality brake piston rotator tool. The Autozone 5 sided cube is no good.

you will have to spin the piston back about 4-5 turns until it fully retracts.

The expanding/ 500lb pressure clamps do no good b/c the brake is like a hydraulic screw. You can't compress this type of brake.
Starting the rotation of the piston back will require two people

1 to hold the tool and ratchet on the piston, the other to turn the ratchet.



Posted on Aug 30, 2008

  • 119 Answers

SOURCE: replacement of coolant temperature sensor

located under intake in water crossover pipe,you can access the sensor by removing intake chamber box,then pcv hose connected to the block,the connector is orangeish 2pin,use a 19mmdeep socket on a 3/8 ratchet to get it loose,make sure engine is cool,also make sure there is a new brass washer with your new sensor,sometimes the old washer comes off when removing the sensor,sometimes it sticks to the pipe,some coolant will escape so make sure to top it off

Posted on Jul 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: where to replace coolant temp sensor for 1998 grand jeep cherokee

Check this image...

b33c4b0.png

...in the Section ZJ-Secc-8D-Ignition-Systems (page 5, fig. 10 and 11).

Good luck.



Posted on Sep 07, 2009

  • 163 Answers

SOURCE: fuel pump relay location on 98 mercury sable

its under the hood on driver side what the problem not starting check the trunk area for the fuel cut off switch poss bad or tripped did u get hit or someone bump ur car

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why isn't my speedometer working& how do I repair it? 1998 mercury sable gs


1997 Mercury Sable LS VSS Vehicle Control Sensor ...

? 2:13
www.youtube.com/watch?v=1O0kJJjjhk0
Jun 1, 2012 - Uploaded by Trevor Harris
I am trying to replace my Vehicle Control Sensor on my 1997Mercury Sable LS 3.0 Liter. Here's the ...

Sep 15, 2015 | Mercury Cars & Trucks

1 Answer

Coolant leak but temperature is reading normal


a leak is a leak shouldn't run hotter unless its very low

May 30, 2012 | 2000 Mercury Sable

1 Answer

Cooling fans not coming on


There is a coolant temperature sensor in the side tank to the radiator. It has probably corroded enough that it no longer functions. You will need to unscrew it from the side tank of the radiator and replace the sensor. This is an easy repair and the part is relatively inexpensive.

Apr 06, 2012 | 2000 Mercury Sable

1 Answer

My 2001 mercury sable runs hot (temperature gauge goes high then drops back at half also


Check your coolant level visually by removing the radiator cap (only when it is cold). Also make sure the coolant temperature sensor for the cooling fan is functioning properly. These are set to operate the fan when the engine coolant reaches a predetermined temperature. These go bad in time and need replacing. Sounds as though yours may be working intermittently.

Apr 06, 2012 | 2001 Mercury Sable

2 Answers

Broken coolant line.


I'm not sure if you can buy just that piece, it's recomended that you replace the entire heater hose assembly.
For reference the NAPA p/n is BK 8155114 go to thier web site and verify this is the part you're needing to replace.
You should flush and replace the coolant if it old.
Hope this help you with your problem.

Jun 10, 2010 | 1997 Mercury Sable

1 Answer

Idles rough when first starting in morning. plugs replaced, new throttle body, two new ignition coils. After a few minutes rough idle goes away. Sometimes causes check engine light to go on. Not consistent...


Sounds like you might have a bad engine coolant temperature sensor. I would have the codes retrieved from the computer to see what sensor/s it is seeing a problem with.

May 20, 2010 | 2000 Mercury Sable

1 Answer

Temperature gage


you are low on coolant and you have brown coolant. need a bypass kit.

tsb 01-11-6. post email and I will send tsb to you.

Jan 16, 2009 | 2000 Mercury Sable

1 Answer

Temperature Gauge Stays Cold on 2005 Sable


look on the intake it should be there

Jan 14, 2009 | 2003 Mercury Sable

Not finding what you are looking for?
1998 Mercury Sable Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...