Question about Dodge Neon

1 Answer

HOW TO TAKE THE CAMSHAFT APART , DO YOU NEED TO TAKE THE HEAD OUT?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

Which engine? An overhead cam you take off without removing the head a internal center cam you have to remove the rockers push rods and lifters. then you can carefully pull it out.

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Timing alignment 2009 dodge journey se 2.4l


you cannot set the timing anymore , the engine computer does that now , have you checked to see if the camshaft position sensor was re-positioned properly .
the exhaust valve camshaft may not be positioned properly.
there are holes in the camshaft pulleys and the cylinder head that must be aligned and retained with bolts before you remove the timing belt / chain

May 28, 2014 | 2009 Dodge Journey

1 Answer

I need the correct timing marks for a 96 miata 1.8


The E mark on the left camshaft pulley should line up with the E mark on the camshaft cover. The I mark on the right camshaft pulley should line up with the I mark on the head. There is also a notch on the top of the bottom pulley that needs to line up with the cast pointer above this pulley. I like to mark stuff when I am taking it apart with white paint, it is easy to see when putting stuff back together. The www.miata.net/garage has some help on this.

Nov 24, 2013 | 1996 Mazda MX-5 Miata

1 Answer

I have a kia sadona and need to replace my rack and pinion. Can I replace it without taking engine out???


To install a camshaft replacement sensor on a 2003 Kia Sedona you will need a screwdriver, a wrench, a break bar and socket, and a camshaft position sensor. To install, make sure the vehicle's ignition switch is turned off and disconnect the negative cable from the battery. Remove the air filter housing from the car by unscrewing the bolts that secure the lid. Rotate the crankshaft. Locate the cylinder head and mount the camshaft sensor onto the cylinder head.---------------------------------------------------------------------------
XPROG-M

Apr 18, 2013 | Cars & Trucks

1 Answer

I installed a new head. i see where u need to line up marks on gears with ones on timing cover. How come some people tell u to line the marks towards each other. also i had to pull exhaust cam to torque...


How to time engine --Turn crankshaft to t.d.c. turn camshaft so valves on number four cylinder start to open and close ( rock back and forth )line up marks on cover and cam gear .key way will line up ,may have to move cam just a bit.

May 17, 2011 | 2000 Daewoo Nubira

2 Answers

Where is camshaft sensor located 2004 sonata v6


Hello police32127. My name is Roger and i will answer your question. To locate the camshaft sensor. Raise he hood stand at the drivers side tire. Look at the cylinder head on your left. You will see it mounted on the head. Sets between the head and the upper radiator hose.
Please rate the answer you received. This way w know your answer helped. Should you need further help please just ask. Thank You for using Fix Ya. Roger

Sep 02, 2009 | Hyundai Motor 2004 Sonata

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Cant find cam sensor in 2004 dodge stratus r/t


2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Feb 12, 2009 | 2004 Dodge Stratus

1 Answer

Camshaft position sensor


The camshaft position sensor is usually located on the cylinder head near the camshaft. It may be under the timing cover. It has a small plug and the sensor is where the plug is plugged on.

Jan 23, 2009 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...