Question about 2009 Audi Q7

Open Question

I spilled red bull on my center console and now none of the instruments work how can i fix this

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flashing instrument cluster display & lights on 05 Odyssey.


It points to a defective instrument panel.

Jun 29, 2017 | AC Cars & Trucks

1 Answer

How to remove center console from 2008 dodge caliber


Hi Rich, hope you well today here's is the fix you need.


23 - Body/Interior/CONSOLE, Center/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure
248438.jpg 1. Pull back on parking brake (5) to the upright position. 2. Open console door and remove two screws (1) fastening console to rear floor bracket (3). 3. Carefully pry up until the retainers (1) disengage from the center console to front floor bracket (6). 4. Disconnect center console wire connector (2) to instrument panel connector. 5. Remove from vehicle.

Hope this help and have an awesome day Rich.

May 23, 2014 | 2008 Dodge Caliber

1 Answer

Sam module


Bad wiring? The wires that go between the car body and doors or in the center console - has someone spilled some coffee or drink in the center console? Is it just one window or several? (just one - I suspect door, several I suspect center console).

Mar 25, 2014 | 2001 Mercedes-Benz CLK-Class

1 Answer

When putting in park, sometimes key wont come all the way back or come out. have to restart the engine put it in drive, then back into park. what could be causing this?


The linear shift cable (Also called Park Lock Cable) is sticking. This happens a lot due to beverages getting spilled in the center console. Removing the center console and cleaning and lubricating the shift mechanism and the end of the cable usually fixes the problem. In other cases, the cable must be replaced.

Sep 16, 2011 | 2002 Pontiac Sunfire

1 Answer

Hi all my power windows stop working, i checked all the fuses and they're all good.


Do the power mirrors still work? Did something get spilled in near the center console? Since all of them quit working and the fuses are good, you need to look under the switches in the center console. your problem should be there. Maybe the main plug came loose.

Sep 23, 2010 | 1996 Saturn SL

1 Answer

Ac blowing heat on side and air on the other side.


Air Door Actuators Removal & Installation Console Mode To Remove:
  1. Remove the center console from the vehicle.
  2. Detach the air outlet duct from the center console.
  3. Disconnect the console mode actuator connector.
  4. Detach the console mode actuator from the center console.
To Install:
  1. Attach the console mode actuator to the center console. Torque the screws to 17 in-lb (1.9 Nm).
  2. Connect the console mode actuator connector.
  3. Attach the air outlet duct to the center console. Torque the screw to 17 in-lb (1.9 Nm).
  4. Install the center console into the vehicle.
Left Side Air Temperature To Remove:
  1. Remove the instrument panel carrier from the instrument panel.
  2. Disconnect the left side air temperature actuator connector. HVAC control module - left side gm-10-00-1844.gif

  3. Detach the left side air temperature actuator from the HVAC module.
To Install:
  1. Attach the left side air temperature actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Connect the left side air temperature actuator connector.
  3. Install the instrument panel carrier onto the instrument panel.
  4. Recalibrate the left side air temperature actuator.
Right Side Air Temperature To Remove:
  1. Remove the instrument panel carrier from the instrument panel.
  2. Disconnect the right side air temperature actuator connector.
  3. Detach the right side air temperature actuator from the HVAC module.
To Install:
  1. Attach the right side air temperature actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Connect the left side air temperature actuator connector.
  3. Install the instrument panel carrier onto the instrument panel.
  4. Recalibrate the right side air temperature actuator.
Mode To Remove:
  1. Remove the left floor duct from under the instrument panel (I/P).
  2. Disconnect the mode actuator connector. HVAC control module - left side gm-10-00-1844.gif

  3. Detach the mode actuator from the HVAC module.
To Install:
  1. If installing a new mode actuator, move the mode door to the middle position.
  2. Attach the mode actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  3. Connect the mode actuator connector.
  4. Install the left floor duct under the instrument panel (I/P).
  5. Recalibrate the mode actuator.
Defrost Valve To Remove:
  1. Remove the instrument panel carrier from the instrument panel.
  2. Disconnect the defrost valve actuator connector. HVAC control module - left side gm-10-00-1844.gif

  3. Detach the defrost valve actuator from the HVAC module.
To Install:
  1. Attach the defrost valve actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Connect the defrost valve actuator connector.
  3. Install the instrument panel carrier onto the instrument panel.
Recirculation To Remove:
  1. Remove the HVAC module from the instrument panel.
  2. Detach the air inlet assembly from the HVAC module. Recirculation actuator removal and installation gm-10-00-1845.gif

  3. Disconnect the recirculation actuator connector.
  4. Detach the recirculation actuator from the HVAC module.
To Install:
  1. Attach the recirculation actuator to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  2. Attach the air inlet assembly to the HVAC module. Torque the screw to 17 in-lb (1.9 Nm).
  3. Connect the recirculation actuator connector.
  4. Install the HVAC module into the instrument panel.
  5. Recalibrate the recirculation actuator.
prev.gif next.gif

Aug 17, 2010 | 2004 GMC Envoy

2 Answers

I changed the battery on 2006 Trailblazer SS. Now I can only get AC from my windshield and floor vents. Nothing from the dash vents. Also the temp control only gives coldest temp. I have checked fuses...


once you disconnect the battery your body control module loses power and memory you have to get some one with a scanner with reprogramming capabilities and have the computers reset ,dealer?

Aug 05, 2010 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

How do I remove heater core on 1997 dodge stratus


prev.gif next.gif Heater Core REMOVAL & INSTALLATION Cirrus, Stratus, Sebring Convertible and Breeze
  1. Disconnect the negative battery cable.
  2. Remove the radio/HVAC control module bezel. CAUTION
    The vehicles covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses air bags. Whenever working near any of the SRS components, such as the impact sensors, air bag modules, steering column and instrument panel, disable the SRS, as described earlier in this section.
  3. Remove the right instrument panel side trim.
  4. Remove the two retaining screws at the lower right side support beam.
  5. Remove the instrument panel support bolt at the A-pillar.
  6. Remove the left instrument panel side trim and upper instrument panel bezel.
  7. Remove the lower knee bolster and console screws at the instrument panel.
  8. Remove the gearshift knob and shifter bezel.
  9. Remove the mounting screws at the front and rear of the floor console. Remove the front and rear console halves.
  10. Remove the right side instrument panel support strut.
  11. Drain the cooling system into a suitable container, then disconnect the heater hoses at the cowl panel. Plug the heater core outlets to prevent coolant from spilling during unit housing removal. Fig. 1: Remove the heater core cover 90906g01.gif
    Fig. 2: Remove the heater core 90906g02.gif

  12. Remove the mounting screws and heater core cover.
  13. Remove the heater core from the vehicle. To install:
  14. Carefully position the heater core unit into the heater housing.
  15. Install the heater core cover onto the heater housing and tighten the mounting screws.
  16. Install the right side instrument panel support strut.
  17. Install the front and rear console halves.
  18. Install the shifter bezel and gearshift knob.
  19. Install the lower knee bolster and console screws at the instrument panel.
  20. Install the upper instrument panel bezel and left instrument panel side trim.
  21. Install the instrument panel support bolt at the A-pillar.
  22. Install the two retaining screws at the lower right side support beam.
  23. Install the right instrument panel side trim.
  24. Install the radio/HVAC control module bezel.
  25. Fill the cooling system to the proper level.
  26. Connect the negative battery cable.
Sebring Coupe and Avenger
  1. Disconnect the negative battery cable. CAUTION
    The vehicles covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses air bags. Whenever working near any of the SRS components, such as the impact sensors, air bag modules, steering column and instrument panel, disable the SRS, as described earlier in this section.
  2. Remove the instrument panel from the vehicle, as outlined in Section 10 of this manual.
  3. Drain the cooling system into a suitable container, then disconnect the heater hoses from the dashboard panel. Plug the heater core outlets to prevent coolant from spilling during unit housing removal.
  4. Remove the center stay.
  5. Remove the lap cooler duct mounting screw. Remove the center duct.
  6. Remove the left and right rear heater ducts.
  7. Remove the foot distribution duct.
  8. If equipped with A/C, remove the cooling unit mounting nut and bolt.
  9. Remove the retainer clip, then the heater unit.
  10. Remove the heater core. Fig. 3: Exploded view of heater unit and core assembly 90906g03.gif
    To install:
  11. Install the heater core into the heater housing.
  12. Install the heater housing and retainer clip into the vehicle.
  13. If equipped with A/C, install the cooling unit mounting bolt and nut.
  14. Install the foot distribution duct. Install the left and right rear heater ducts.
  15. Install the center duct, then install the lap cooler duct mounting screw.
  16. Install the center stay and connect the heater hoses to the heater core at the dashboard panel.
  17. Install the instrument panel.
  18. Fill the cooling system to the proper level.
  19. Connect the negative battery cable.

Jul 08, 2010 | 1997 Dodge Stratus

1 Answer

How do I change the starter on a 96 sebring coupe


Are you sure it is the starter? This is a picture of where the starter relay is....may be easier and cleaner to change this first....unless it is your starter...none-the-less....here is the info....and not sure the size of motor so pick accordingly:


RELAY REPLACEMENT


See Figure 15
On Cirrus, Stratus, Sebring convertible and Breeze models, the starter relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location.
On Sebring and Avenger coupes, the starter relay is located under the instrument panel, behind the instrument panel/center console panel. It may only be necessary to remove the center console panel to access the starter relay. However, if the entire console requires removal, refer to .

9ff1184.gif

Oct 09, 2009 | 1996 Chrysler Sebring

Not finding what you are looking for?
2009 Audi Q7 Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...