Question about 1996 Chevrolet Corsica

1 Answer

96 corsica error cod po441 no purge flow

I have 96 corsica 103,000 miles
smoked vacuum lines found no leaks
replaced gas cap
replaced rubber line to charcoal canister
resealed vacuum line that attaches to intake by pcv valve
replaced charcoal canister
service engine light still comes on after a few days driveing with same code po441 no purge flow
Please help

Posted by on

  • 1 more comment 
  • Anonymous Mar 15, 2014

    check engine light is on

  • Anonymous Mar 22, 2014

    The alternator hot lead at the back of the alternator shorted out against the metal vacuum rubes that come from the charcoal canister that runs behind the alt. Now the engine won't turn over or run even when I turn the ign on & use a remote starter switch. The ONLY things that work are the headlights & horn. Not even the dash lights come on when I turn on the ign switch!

  • Anonymous Mar 30, 2014

    CODES- FOR LEAN O2 AND LOW PURGE VALVE EVAP CANISTER / FOUND VACCUM LINES ROTTED, CAN'T FIND CANISTER. ENGINE LOOSES POWER AFTER 100MI.INTERSTATE SPEED,VERY SLOW ACCEL 50-70MPH LOOSES IT COMPLETELY 49-0. SUSPECT FUEL TANK SUCTION BUILD-UP BECAUSE OF CANISTER NO PURGE

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Look, that code means:
P0441 - Evap emission control system Incorrect purge flow

so try to replace the emission control.

Posted on Jun 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Codes0441 0442 0455 0456


codes po441 po442 po455 po456. code po441 - EVAP system no flow during purge conditions.code po442 -EVAP system small leak detected conditions. code po455 - EVAP system large leak detected conditions.code po456 - EVAP system very small leak detected. possible causes loose damaged missing fuel cap.fuel tank sensor disconnected or failed. ORING on top fuel sending unit leaking.purge valve vapor line clogged disconnected or purge solenoid failed.vent solenoid not closing or has failed.

May 23, 2013 | 2002 Dodge Durango

1 Answer

Po441 2002 Hyundai, engine hard starting after fill up


Most likely is a bad EVAP purge valve. But check below list.
This indicates that a part of the EVAP control system is no longer functioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle'sicon1.png fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is controlled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

  • Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM
Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Replace Leak Detection Pump / LDP
  • Repair damaged EVAP lines or canister
  • Repair open or short in voltage feed circuit to Purge Solenoid
  • Repair open in PCM purge command circuit
  • Replace purge Solenoid
  • Replace vacuum switch
  • Repair restriction in Evap line or canister or solenoid
  • Repair resistance in purge connector
  • Replace PCM

Oct 24, 2012 | Hyundai Elantra Cars & Trucks

2 Answers

01 camry code po441...start with gascap?


This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.

Causes: A code P0441 could mean one or more of the following has happened:
Bad vacuum switch
Broken or damaged EVAP line or canister
Open in PCM purge command circuit
Open or short in Voltage feed circuit to Purge Solenoid
Faulty purge solenoid
Restriction in EVAP solenoid, line or canister
Corrosion or resistance in purge connector
Bad PCM

Possible Solutions: with a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Common Chrysler fix - Replace Leak Detection Pump / LDP
Repair damaged EVAP lines or canister
Repair open or short in voltage feed circuit to Purge Solenoid
Repair open in PCM purge command circuit
Replace purge Solenoid
Replace vacuum switch
Repair restriction in Evap line or canister or soleniod
Repair resistance in purge connector
Replace PCM

Hope this helps.

Aug 03, 2011 | 2001 Toyota Camry

1 Answer

I have a toyota matrix w/ 88,000 miles 2006. I have the check engine light on, took it to advance auto, codes are PO441- EVAP control system , purge flow-fault also PO455 EVAP system-large leak I don't...


P0441 Evaporative Emission Control System Incorrect Purge Flow
OBD-II Trouble Code Technical Description

Evaporative Emission Control System Incorrect Purge Flow
What does that mean?

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or soleniod
* Repair resistance in purge connector
* Replace PCM
THIS IS LIKELY FROM TOPPING OFF THE TANK EACH TIME YOU FUEL UP



P0455 is similar:

Technical Description

Evaporative Emission Control System Leak Detected (no purge flow or large leak)
What does that mean?

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Symptoms

You likely won't notice any drivability problems.
Causes

A code p0455 most likely means one or more of the following has happened:

* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* Other leak or damaged piece in EVAP system

Possible Solutions

With a p0455, the most common repair is to:

* Remove and reinstall the gas cap, have AutoZone clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, and/or
* Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 05, 2010 | 2006 Toyota Matrix

1 Answer

2003 DARANGO SLT 4.7 -2 WD, AUTO, 99K MILES, CODE PO441 WITH KEY


0441 the most common fix for this code in chrysler/dodge vehicles is to replace the leak detection pump / ldp -----other areas to check would be damage / restriction in evap line / canister---faulty purge solenoid or connection damage or resistance in line -bad vacuum switch

Apr 28, 2010 | 2004 Hummer H2

3 Answers

Po441 emissions code for a 2000 Avalon - just wondering some possibilities on what it might be and what it will cost.


This indicates that a part of the EVAP control system is no longer functioning correctly.

FIRST, call the local Toyota dealer, tell them the error and your mileage. It MAY be covered under warranty as part of the emissions system, which many manufacturers have extended warranty programs on at no cost to you.

A code P0441 could mean one or more of the following has happened:
  • Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Repair damaged EVAP lines or canister
  • Repair open or short in voltage feed circuit to Purge Solenoid
  • Repair open in PCM purge command circuit
  • Replace purge Solenoid
  • Replace vacuum switch
  • Repair restriction in Evap line or canister or soleniod
  • Repair resistance in purge connector
  • Replace PCM
.

Nov 14, 2009 | 2000 Toyota Avalon

4 Answers

Error code p 0441


P0441 Evaporative Emission Control System Incorrect Purge Flow OBD-II Trouble Code Technical Description Evaporative Emission Control System Incorrect Purge Flow
What does that mean? This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system
. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
copyscape.gif Symptoms Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes A code P0441 could mean one or more of the following has happened:
  • Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM
Possible Solutions With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Common Chrysler fix - Replace Leak Detection Pump / LDP
  • Repair damaged EVAP lines or canister
  • Repair open or short in voltage feed circuit to Purge Solenoid
  • Repair open in PCM purge command circuit
  • Replace purge Solenoid
  • Replace vacuum switch
  • Repair restriction in Evap line or canister or soleniod
  • Repair resistance in purge connector
  • Replace PCM

Oct 05, 2009 | 2003 Dodge Intrepid

2 Answers

Error codes P0442 and P0455 in Dodge Dakota 2001


Hello shoretex...Yes sir you can repair this yourself...
p0442 is medium leak detected ...p0456 is small leak....and p0440 is a general evap system failure.. evap codes are a common thing. gas caps are an inexpensive place to start. There are two types of evap hoses on the Dodge... hard plastic and soft rubber.... before you replace parts check the soft rubber first at the evap cans and pump located about a foot in front of the gas tank fill pipe on trucks located next to the transfer case or right behind the trans on the driver side. hard plastic lines will brake or rub through...check spots where lines come in contact with anything. this is a common thing with older trucks...hair line cracks will kick a p0442 code, and a p0445 code...When you find a leak, repair it, and rescan...sometimes there are several leaks, continue with inspection and repairs until you get it all fixed up.... Remember..start at simple and work from there...
i will post the evap. system in more detail to help you troubleshoot the problem.
EVAP System: The Evaporative Emission (EVAP) Control system used on all vehicles is the charcoal canister storage method. This method transfers fuel vapor from the fuel tank to an activated carbon (charcoal) storage device (canister) to hold the vapors when the vehicle is not operating. When the engine is operating, the fuel vapor is purged from the carbon element by intake air flow and consumed in the normal combustion process. The evaporative system includes the following components: *Fuel tank *Evaporative emission canister vent solenoid *Fuel tank pressure sensor *Fuel pipes and hoses *Vapor lines *Fuel cap *Evaporative emission canister *Purge lines *Purge valve solenoid EVAP System Operation: The EVAP purge solenoid valve allows manifold vacuum to purge the canister. The Powertrain Control Module (PCM) supplies a ground to energize the EVAP purge solenoid valve (purge on). The EVAP purge solenoid control is Pulse Width Modulated (PWM) or turned on and off several times a second. The EVAP canister purge PWM duty cycle varies according to the operating conditions determined by the mass air flow, the fuel trim, the engine coolant temperature, and the intake air temperature. For certain EVAP tests, the diagnostic will be disabled if the TP angle increases to above 75% . The evaporative leak detection diagnostic strategy is based on applying vacuum to the EVAP system and monitoring for vacuum decay. The fuel level sensor input to the PCM is used to determine if the fuel level in the tank is correct to run the EVAP diagnostic tests. To ensure sufficient volume in the tank to begin the various diagnostic tests, the fuel level must be between 15% and 85% . The PCM monitors the fuel tank pressure/vacuum level via the fuel tank pressure sensor input. Results of Incorrect Operation: Poor idle, stalling and poor driveability can be caused by the following: *Malfunctioning purge solenoid. *Damaged canister. *Hoses/lines split, cracked and/or not connected properly. Evidence of fuel loss or fuel vapor odor can be caused by the following: *Liquid fuel leaking from the fuel lines *Cracked or damaged canister *Inoperative canister control valve Vacuum hoses that are: *Disconnected *Mis-routed *Kinked *Deteriorated *Damaged The evaporative leak detection diagnostic strategy is based on applying vacuum to the EVAP system and monitoring vacuum decay. The PCM monitors vacuum level via the fuel tank pressure sensor input. At an appropriate time, the EVAP purge solenoid and the EVAP vent solenoid are turned on, allowing engine vacuum to draw a small vacuum on the entire evaporative emission system. After the desired vacuum level has been achieved, the EVAP purge solenoid is turned off, sealing the system. A leak is detected by monitoring for a decrease in vacuum level over a given time period, all other variables remaining constant. A small leak in the system causes DTC P0442 to be set. If the desired vacuum level cannot be achieved in the test described above, a large leak or a faulty EVAP purge solenoid is indicated. This can be caused by the following conditions: *Disconnected or faulty fuel tank pressure sensor. *Missing or faulty fuel cap. *Disconnected, damaged, pinched, or blocked EVAP purge line. *Disconnected or damaged EVAP vent hose. *Disconnected, damaged, pinched, or blocked fuel tank vapor line. *Disconnected or faulty EVAP canister solenoid. *Disconnected or faulty EVAP vent solenoid. *Open ignition feed circuit to the EVAP vent or purge solenoid. *Damaged EVAP canister. Any of the above conditions sets DTC P0440. A restricted or blocked EVAP canister vent path is detected by drawing vacuum into the EVAP system. The PCM turns off the EVAP vent solenoid and the EVAP purge solenoid (EVAP vent solenoid Open, EVAP purge PWM 0% ). The PCM monitors the fuel tank pressure sensor input. With the EVAP vent solenoid open, any vacuum in the system should decrease quickly unless the vent is blocked. A blockage is caused by the following conditions: *Faulty EVAP vent solenoid (stuck closed). *Plugged, kinked, or pinched vent hose. *Shorted EVAP vent solenoid driver circuit. *Plugged evaporative canister.

Good luck shoretex, hope this helps...please take time to rate me a fixya.

Jul 20, 2009 | 2001 Dodge Dakota

7 Answers

I have fault code P0441 showing up on my 2003 Dodge Durango. Not sure what this code is, or how to correct it..


P0441--
Evaporative Emission Control System Incorrect Purge Flow.

This indicates that a part of the EVAP control system is no longer functioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is controlled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.

A code P0441 could mean one or more of the following has happened:

* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Here are a few solutions that should be followed to fix this issue.

* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or solenoid
* Repair resistance in purge connector
* Replace PCM


Please rate and god bless:)

Apr 14, 2009 | 2001 Dodge Durango

2 Answers

Trouble codes on a 96 buick riv


A code P0441 could mean one or more of the following has happened:
  • Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM
Possible Solutions With a P0441 OBD-II trouble code
, diagnosis can be tricky at times. Here are some things to try:
  • Common Chrysler fix - Replace Leak Detection Pump / LDP
  • Repair damaged EVAP lines or canister
  • Repair open or short in voltage feed circuit to Purge Solenoid
  • Repair open in PCM purge command circuit
  • Replace purge Solenoid
  • Replace vacuum switch
  • Repair restriction in Evap line or canister or soleniod
  • Repair resistance in purge connector
  • Replace PCM
http://www.justanswer.com/questions/33aog-hi-got-code-p0742-and-ever-now-and-then-it-will-not-shift-right
This link will help with your transmission diagnosis.

Apr 05, 2009 | 1996 Buick Riviera

Not finding what you are looking for?
1996 Chevrolet Corsica Logo

742 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...