Question about 2001 Hyundai Santa Fe

1 Answer

Hyundai santa fe 2001

1 jolts from 2nd - 3rd or visa versa
2a then check engine light comes on
2b only 2nd and 3rd gear accessible
2c codes that appear are p0715 and p1529
3 after 1 day or so resets and CEL goes off
4 back to normal until cycle repeats
5 The garage changed the speed sensor (located under airfilter)
6 problem seemed to disappear, but only for 1 day
7 HELP!!!

Posted by on

  • errolsweet39 Dec 02, 2008

    I have a hyundai santa fe that has the same erotic engine performance and the light comes on. Have not yet changed the speed censor. If you could point me in the right direction I would be thankful.



    Thank you

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

P0715 > A/T input speed sensor circuithyundai santa fe 2001 - e05139a.jpg 1. Many malfunctions in the electrical system are caused by poor harness and terminals. Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage. 2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. P1729>This DTC code is related to the EMC and is set If EMS harness has an open battery source addcfc2.jpg 1. Ignition OFF 2. M54 Electric Magnet Valve Clutch connector : Disconnect. 3. Measure resistance between 1 & 2. A. Specification : Approx. 1.8 ~ 2.2 Ωc7c6e73.gif The above value is only for reference. The data from vehicle may differ from it according as various vehicle condition. This inspection is for checking open or short of EMC coil.

Posted on Jun 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hyundai santa fe 2001


Car error codes::


Diagnostic Trouble Code Storage Condition Remedy
P0100 Mass Air Flow Sensor Voltage High C-8
P0100 Mass Air Flow Sensor Voltage Low C-8
P0110 Intake Air Temperature Voltage High C-10
P0110 Intake Air Temperature Voltage Low C-10
P0115 Coolant Temperature Voltage High C-9
P0115 Coolant Temperature Voltage Low C-9
P0120 Throttle Position Sensor (TPS) Voltage High C-7
P0120 Throttle Position Sensor (TPS) Voltage Low C-7
P0130 O2 Sensor 1 Circuit Voltage High C-30
P0130 O2 Sensor 1 Circuit Voltage Low C-30
P0130 O2 Sensor 1 Open Circuit C-30
P0150 O2 Sensor 2 Circuit Voltage High C-31
P0150 O2 Sensor 2 Circuit Voltage Low C-31
P0150 O2 Sensor 2 Open Circuit C-31
P0201 Injector Valve 1 Voltage High C-20
P0201 Injector Valve 1 Voltage Low C-20
P0201 Injector Valve 1 Open Circuit C-20
P0202 Injector Valve 2 Voltage High C-21
P0202 Injector Valve 2 Voltage Low C-21
P0202 Injector Valve 2 Open Circuit C-21
P0203 Injector Valve 3 Voltage High C-22
P0203 Injector Valve 3 Voltage Low C-22
P0203 Injector Valve 3 Open Circuit C-22
P0204 Injector Valve 4 Voltage High C-23
P0204 Injector Valve 4 Voltage Low C-23
P0204 Injector Valve 4 Open Circuit C-23
P0205 Injector Valve 5 Voltage High C-24
P0205 Injector Valve 5 Voltage Low C-24
P0205 Injector Valve 5 Open Circuit C-24
P0206 Injector Valve 6 Voltage High C-25
P0206 Injector Valve 6 Voltage Low C-25
P0206 Injector Valve 6 Open Circuit C-25
P0230 Fuel Pump Relay Voltage High C-6
P0230 Fuel Pump Relay Voltage Low C-6
P0230 Fuel Pump Relay Open Circuit C-6
P0325 Knock Signal Circuit 1 C-26
P0330 Knock Signal Circuit 2 C-26
P0335 No Engine RPM Signal C-32
P0335 Incorrect RPM Signal C-32
P0340 Hall Sensor Voltage High C-15
P0340 Hall Sensor Voltage Low C-15
P0403 EGR Valve Voltage High C-28
P0403 EGR Valve Voltage Low C-28
P0403 EGR Valve Open Circuit C-28
P0410 Secondary Air Pump Voltage High C-27
P0410 Secondary Air Pump Voltage Low C-27
P0443 Fuel Tank Ventilation Valve Voltage High C-29
P0443 Fuel Tank Ventilation Valve Voltage Low C-29
P0443 Fuel Tank Ventilation Open Circuit C-29
P0500 Vehicle Speed Signal C-42
P0505 Idle Air Control Voltage High C-33
P0505 Idle Air Control Voltage Low C-33
P0550 Power Steering Voltage High C-14
P0550 Power Steering Voltage Low C-14
P0560 Battery Voltage High C-4
P0560 Battery Voltage Low C-4
P0602 Control Module Programming Error C-2
P1110 Intake Manifold Valve 1 Voltage High C-34
P1110 Intake Manifold Valve 1 Voltage Low C-34
P1111 Intake Manifold Valve 2 Voltage High C-35
P1111 Intake Manifold Valve 2 Voltage Low C-35
P1230 Power Supply Relay Secondary Circuit C-3
P1405 EGR Valve Feedb. Voltage High C-28
P1405 EGR Valve Feedb. Voltage Low C-28
P1405 EGR Valve Feedb. Incorrect Signal C-28
P1501 Immobiliser No or Wrong Coding C-5
P1502 Immobiliser No Signal C-5
P1503 Immobiliser Wrong Signal C-5
P1530 A/C Relay Voltage High C-41
P1530 A/C Relay Voltage Low C-41
P1600 Reprogram or Replace Electronic Control Unit (ECU) C-2
P1602 Knock Control Module; Replace ECU C-2
P1690 Check Light Voltage High C-43
P1690 Check Light Voltage Low C-43
P1690 Check Light Open Circuit C-43
P1740 Torque Control Voltage Low C-40
P1740 Continuous Torque Control C-40

These are the error codes:

Jul 08, 2008 | 2001 Hyundai Santa Fe

1 Answer

Hyundai Santa Fe 2001 Engine light won't go off!


try getting new gas cap tis makes light come on a lot.you cant get it reset with code scanner something is wrong

Feb 21, 2010 | 2001 Hyundai Santa Fe

2 Answers

2001 Hyundai Santa Fe check engine light and transmision troubles


your guess is as good as anyones. Someone will have to look at this in person.

Nov 18, 2009 | 2001 Hyundai Santa Fe

1 Answer

Car will not shift out of 1st gear


Did the 'Check Engine' Light come ON? Whenever the 'CHECK ENGINE' light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on.
You'll need to use/find an OBDII (On-Board Diagnostic) Scanner to retrieve any code which have been stored in the ECU computer. Afterward, we might be able to help you DIAGNOSE and perhaps eventually fix the problem.

Oct 27, 2009 | 2001 Hyundai Santa Fe

1 Answer

My 01 hyundia santa fe sounds like a golf cart it sounds like power steering but thats not the problem also when i accelerate it will jolt and will only work in 3rd or 2nd gear so i haft to take off in 2nd...


Did the 'Check Engine' Light come ON? Whenever the 'CHECK ENGINE' light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on. You'll need to use/find an OBDII (On-Board Diagnostic) Scanner to retrieve any code which have been stored in the ECU computer. Afterward, we might be able to help you DIAGNOSE and perhaps eventually fix the problem.

Oct 20, 2009 | 2001 Hyundai Santa Fe

1 Answer

Car will not accelerate in high gears, and does


Ok... do you have the maintenance history on this vehicle? Did the 'Check Engine' Light come ON? Whenever the 'CHECK ENGINE' light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on. You'll need to use/find an OBDII (On-Board Diagnostic) Scanner to retrieve any code which have been stored in the ECU computer. Afterward, we might be able to help you DIAGNOSE and perhaps eventually fix the problem.

Jul 31, 2009 | 2001 Hyundai Santa Fe

4 Answers

2001 Hyundai Santa Fe - Engine Code P1602, stuck in gear


Im having the same problem with my 02 Santa Fe. How do i go about fixing this problem? And is it costly? Please help

May 20, 2009 | 2001 Hyundai Santa Fe

1 Answer

Santa Fe Code p1529


I am sorry the above codes is general error code , the error your getting is car specific hence the codes where not there in the list:

P0715
Input speed sensor system

If no output pulse is detected from the input shaft speed (PG-A) sensor for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h or more, it is judged to be an open or short circuit . In the input shaft speed sensor and diagnosis code P0715 is output. If diagnosis code P0715 is output four times, the transmission is locked into 3rd gear (D range) or 2nd gear as a fail-safe measure

P1529
TCM MIL request signal, this code sets in the computer engine control module when there is a transmission fault code

Jul 08, 2008 | 2001 Hyundai Santa Fe

Not finding what you are looking for?
2001 Hyundai Santa Fe Logo

1,030 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...