Question about 1995 Pontiac Bonneville

1 Answer

How difficult to reseal intake manifold? - 1995 Pontiac Bonneville

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 277 Answers

You would be better off to buy a new one.
they have them at the auto parts stores now.
was a big problem with the plastic one's

Posted on Nov 15, 2010

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: intake manifold installing..... difficult?

i replace the intake manifold on my 98 crown vic . its was easy just take your time take pictures. the hardest part for me was two bolts in back of the heads facing the firewall once you get those it quite easy after that. plus you save your self a least 500.00 dollars. good luck

Posted on Apr 27, 2009

  • 97 Answers

SOURCE: resealed intake manifold on 1997 chevy tahoe.truck

make sure oil sending unit is plugged in check for vacuum leak between two piece manifold pull spark plugs after trying to start look for wet gas foul

Posted on Feb 21, 2010

Testimonial: "thanx. iwill try it out."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Sebring Touring 2.7. Where is the knock sensor located?


This knock sensor is very difficult to access. It is located between the two cylinder banks, it screws into the cylinder block underneath the intake manifold.

In order to remove the sensor the intake manifold and right cylinder head must be removed.

Nate

Aug 23, 2015 | Chrysler Sebring Cars & Trucks

3 Answers

Coolant leaking from cracked intake manifold, repair shop says intake manifold must be replaced.


It is difficult to repair a crack in an intake manifold, so replacing it is a good solution. You may want to consider a used manifold you can get from an automobile recycler. This can save a lot of money for you. It is also a good reliable fix because intake manifolds rarely fail, so a used part will be reliable.

Dec 17, 2010 | 1999 Lincoln Town Car

1 Answer

'06 chevy aveo vacuum leak at the intake manifold. Is this a common problem with the aveo's? Can it be sealed without removing the manifold? Also, are throttle position sensors a common problem with aveos?


Proper resealing and problem resolution (warpage, etc.) cannot be done without removing and inspecting...
TPI sensors are problems on many cars, not a huge deal....

Sep 11, 2010 | 2006 Chevrolet Aveo

1 Answer

How to replace a starter on an 97 olds aurora with a northstar 4.0


Not sure how different, but on the 2001 4.0 you remove the fuel rails and intake manifold. Starter is under the intake manifold. Not too difficult of a job.

May 06, 2010 | 1997 Oldsmobile Aurora

1 Answer

How to replace the intake manifold? I have a 96 grand cherokee v8, unable to replace the thermostat housing to the manifold because one of the screw holes cracked off on the manifold.


Position The Intake Manifold Gasket On The Engine.Dowels May Be Provided To Hold The Gasket In Place During Manifold Installation.. The Use Of Silicone Sealer Is Required. Especially Where The Front And The Rear Seals Meet The Side Gaskets On V-type Engines. Installing An Intake Manifold On V-type Engines Can Be Difficult. It Is Critical That You Use Sealer Properly On The Engine To Prevent Vacuum,Coolant, And Oil Leaks.

Start All The Fasteners By Hand Before Tightening. This Will Aid In Bolt Hold Alignment. Then Torque The Intake Manifold Fasteners To Specifications. Use The Specific Torque Pattern Given In The Service Manual.. Basically The Pattern Will Be A Crisscross Pattern

Apr 09, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Resealed intake manifold on 1997 chevy tahoe.truck now is a no start .good fuel pressure. timiinng dead on,good spark. any ideas


make sure oil sending unit is plugged in check for vacuum leak between two piece manifold pull spark plugs after trying to start look for wet gas foul

Feb 21, 2010 | 1997 Chevrolet Tahoe

1 Answer

Tune up questions?


first you need to tell us what size engine,but you do not remove intake for plugs or wires,this is done from under vehicle.

Jan 26, 2010 | 1997 Plymouth Grand Voyager

3 Answers

Intake manifold installing..... difficult?


i replace the intake manifold on my 98 crown vic . its was easy just take your time take pictures. the hardest part for me was two bolts in back of the heads facing the firewall once you get those it quite easy after that. plus you save your self a least 500.00 dollars. good luck

Apr 23, 2009 | 1998 Ford Crown Victoria

1 Answer

XJ8 Knock Sensor


Pretty Difficult you have to remove the complete intake and injector rail. You will need both side intake gaskets and the plenum gasket.

Dec 12, 2008 | 2001 Jaguar XJ8

1 Answer

Running Lean


if the engine is still running lean, I would replace the Oxy sensor (s),
Then check for a vaccum leak, I found a very large leak on my intake manifold... there is a cap on a nipple on the engine side lower intake manifold (very difficult to get to) and I could not see it until I removed the intake and looked at it.
On my engine, this cap made of rubber was rotten and leaking vaccum.

This helped me 100%

Oct 22, 2008 | 1999 Ford Escort

Not finding what you are looking for?
1995 Pontiac Bonneville Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...