Question about Chevrolet Blazer

Open Question

How to replce encoder motor on 98 blazer 4x4 cant get it to line up

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimbopickens
  • 56 Answers

SOURCE: 98 chevy s10 blazer turn signal

Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!

PLEASE RATE THIS SOLUTION! Thank You Very Much!

Posted on Nov 25, 2008

  • 5 Answers

SOURCE: what transmission interchanges with a 98 4z`x4 Blazer

sorry but your stuck with the 4l60e if you want it to be right. as for using the bravada transmission thats fine you just have to use your transfer case. your transfer case uses a switch on the dash and an electric motor on the transfer case. the bravada uses a series of sensors on the front and rear axle that sense wheel slippage and send a signal to the electric motor on the transfer case causing it to lock in four wheel drive. when the sensors dont sense wheel slippage any more the system returns to two wheel drive. that,s why they call it smart track. just unbolt your transfer case from your transmission and bolt it to the bravada transmission and install it. p.s- dont forget to at least change the front pump converter seal. for 4 or 5 bucks it,s cheap insurance against a major leak and i dont think you want to pull that transmission out again and yes i saw that happen to many times. good luck.-G.J.M

Posted on Feb 08, 2009

  • 124 Answers

SOURCE: where is the 4x4 encoder motor sensor located on my 03 sierra

the encoder motor sensor is inside the encoder motor. the encoder is located at the transfer case. Remove the encoder and by part number 88962315 this is the sensor. you will have to retime the motor after
hope this helps

Posted on May 06, 2009

  • 1 Answer

SOURCE: 4x4 not wprking in my 98 blazer

where is the actuater lokated on a 2000 gmc jimmy 4x4 will not come on

Posted on Jan 18, 2010

  • 189 Answers

SOURCE: 98 blazer won't engage front wheels encoder motor

while its running,have someone press the buttons on the dash,while you look at the actuator. you should be able to see it working . if not,then follow the vacuum line down to transfer case,and make sure its still connecte,and look at all connections to case and be sure they arent loose. also,make sure the battery tray isnt pinching the lines.

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A buddy of mine has a s10 2001 blazer and the 4x4 isn't working, and was wondering how to replace the vacuum hose, if this is causing the problem?


2001 does not utilize vacuum to engage the front axel. A cable is used. There are a few conditions that can cause this. The most likely is the encoder motor. It's best to have the vehicle scanned. The TCCM is located behind the right kick panel, sometimes if it's unplugged and plugged back in, it will begin to work again.

Feb 28, 2013 | 2001 Chevrolet Chevrolet Blazer

1 Answer

200 chevy blazer 4x4 is not workin it is push button and the indicator lights dont light up at all


Check the fuse in the fuse box first and replace if the fuse is bad. If the replacement fuse goes bad again, check the wire harness at the encoder motor on the transfer-case. Look for any damages causing a short making the fuse to go bad, once the harness and connectors are good. Inspect the encoder motor, check to see if it's not the problem causing the fuse to go bad and if it is. Replace the encoder motor, good luck and keep me posted.

Feb 21, 2010 | 2000 Chevrolet Blazer

1 Answer

98 blazer won't engage front wheels encoder motor is working and has a new vacuum actuator. It says it is in 4 on the button lights but in only 2 wheel. how can i check if the actuator is gitting vac,


while its running,have someone press the buttons on the dash,while you look at the actuator. you should be able to see it working . if not,then follow the vacuum line down to transfer case,and make sure its still connecte,and look at all connections to case and be sure they arent loose. also,make sure the battery tray isnt pinching the lines.

Jan 20, 2010 | 1998 Chevrolet Blazer

3 Answers

1991 Chevy S10 Blazer 4.3 4x4


4170636.jpgThis is all I've got.Hope this helps?

Dec 20, 2009 | 1991 Chevrolet S-10 Blazer

1 Answer

Dipstick tube leaking


cheek to make sure its not over full also the trans lines r right there make sure it not them spayin over after all u just did the motor and the trans was most likly hangin

Nov 15, 2009 | 1998 Chevrolet Blazer

3 Answers

4x4 doesn't engage


Mine was doing the same thing. Check the vacuum lines near the top center of the firewall. one of mine was disconnected and the problem was solved when i pluged it back in

Aug 09, 2009 | 2001 Chevrolet Blazer

2 Answers

Where is the 4x4 encoder motor sensor located on my 03 sierra


the encoder motor sensor is inside the encoder motor. the encoder is located at the transfer case. Remove the encoder and by part number 88962315 this is the sensor. you will have to retime the motor after
hope this helps

Feb 16, 2009 | 2003 GMC Sierra

2 Answers

1998 chevy blazer won't go in to four wheel drive


It sounds like the encoder motor. That's the black plastic box on the driver's side of the transfer case. But just to make sure, the control module for the encoder motor is located behind the passenger side kick plate (inside the vehicle, passenger side, where your feet would be, outside side). Disconnect it for a few seconds and then reconnect it. If the problem still exists, you will have to repair or change your encoder motor. I grabbed one at a scrap yard for less than $100.00.

Nov 27, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...