Question about 1992 Oldsmobile Cutlass

Open Question

How to replace ignition lock cylinder on a 92 olds cutlass supreme international

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: type of freon used in 1990 olds cutlass supreme. new or old?

This car uses r12 freon that is the old stuff but you can have your system converted over to the 134a.

Posted on Jun 18, 2009

GM Elec
  • 1000 Answers

SOURCE: I need the firing order of an Olds Cutlass Supreme

Diagram below, Good luck.
Regards,
2c55fa0.jpg

Posted on Mar 09, 2009

Molson02536
  • 3854 Answers

SOURCE: how hard is it to replace a intake gasket on a 1994 olds cutlass supreme.3.1 6 cyclinder

It is not an extremely difficult job. time consuming consuming... I've done a 3.4 intake manifold job, which in my opinion (plenty will disagree) is a little easier than a 3.1 manifold. there are just more steps involved with the 3.1 intake.(I haven't had to change the intake gasket on my 3.1 (yet)) If you haven't already, invest in a haynes or chilton manual, whip out your sockets and your gasket remover, and prepare to do battle...
oh, as far as how to tell before you break down the engine... are you having any drive ability problems? Surging idle, stalling... try this, take propane torch (DONT LIGHT IT) but open the valve and let the spray the propane around your intake manifold with the engine running. If the idle drops or the car stalls, there is your intake leak. That trick also works with intake cleaner too.

you may have to remove your push rods to put your new gasket on. Just loosen the rocker arm nuts/bolts and pivot your rocker arms out of the way. If you do remove your push rods, push them into some holes in a cardboard box so that you can replace them EXACTLY in the same position that you got them from. To remove old traces of gasket, you may have to get some spray on gasket remover, let it sit 5 min. then get at it with your scraper. (be careful, remember our engines are aluminum, you don't want to scrape too hard and scar the mating surface).  
After you get all the old gasket off, clean the mating surface with intake cleaner or lacquer thinner. your gasket kit may have come with end seals. if it did not, remember to run a line of RTV sealant on the front and rear ridges of the engine block between the heads (before you install the intake gasket.)

When you re-install your lower manifold, coat your bolts with pipe thread sealant. when you install the lower manifold, tighten the vertical bolts first, then the angle bolts- it will keep the manifold from wiggling around on the gasket.

After you get everything back together and all snug, i would buy some GM top engine cleaner (liquid)(dealer only( part# 1050002) or some sea foam from your local parts retailer. I know this is to clean the carbon and sludge from your intake and your cylinders, but guess where the remainder of the solution ends up? Yep, in your oil. That should clean up any residue you had from the milkshake effect.

To use the GM engine cleaner, just disconnect your favorite vacuum hose leading to the intake (some people just use their brake booster hose) and put it down in the bottle of liquid while the car is running. (don't let the vacuum **** the liquid too fast, you don't want to risk problems. you may have to keep your hand on the throttle to keep it running. when the can is empty, let your car stall or just cut it off. 

Let your car sit about 2 hours, to give the cleaner time to really work. Start your car, let it run for about 20 mins (there will be PLENTY of white smoke, your car is burning off the cleaner and the carbon).

Then change your oil. good luck and hope this helps.

Ok, you're going to need to buy, borrow, or rent a torque wrench. For 3.1 engines 1995 and earlier, rocker arm nuts should be torqued to 18 ft-lbs.

The wire brush probably did less damage than I do on a regular basis with a gasket scraper :D so you should be okay. If you've already drained your oil, (which I suspect you have) then I would just use the wal-mart brand while you do the GM engine cleaner thing. 
  Don't add the cleaner to your oil, just let a vacuum hose, **** it into the intake. Plenty will get in your oil. Getting into your oil and cleaning up the gook is just a fringe benefit. What the cleaner actually does is it cleans up your entire intake path (manifold, injectors, & valves)... I think you'll be happy with the throtle crispness, once you're done with the engine cleaner. 
Oh and for your coolant system, just get some Prestone radiator flush, and follow what the bottle says. If your system is really gooped up, Prestone also has a Super flush for a little extra :2cents:


Posted on May 02, 2009

dburns60
  • 410 Answers

SOURCE: I need to replace turn signal switch on 97 olds cutlass supreme.

Disconnect the battery to do any service on the steering column or front radiator areas.

Posted on Jun 30, 2009

  • 12 Answers

SOURCE: how do i replace ignition lock for 97 cutlass

Remove the steering wheel, air bag and coil.

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What makes the fuel pump not kick on on a 92 Oldsmobile Cutlass


There is a red wire close to the battery in the front. It's not connected to anything. Apply positive voltage and that will run your pump for testing purposes.

Dec 08, 2015 | Oldsmobile Cars & Trucks

1 Answer

Where is the temperature sender on a 92 Olds cutlass supreme 3.4 engine


1992 Oldsmobile Cutlass Supreme 3.4L SFI DOHC 6cyl

The Engine Temperature Sensor is located: Under hood, driver side, upper engine area, mounted on rear cylinder head

Jul 13, 2015 | Cars & Trucks

1 Answer

Mixed up wires on ignition coil 92 olds 3.1


So what you are saying is you need the firing order.

Firing order or plug wire placement is - -
passenger side to driver side coils Left to Right = 1-4 6-3 2-5
Cylinders are 1-3-5 on the firewall side and 2-4-6 on the radiator side.

Feb 04, 2013 | 1992 Oldsmobile Cutlass Supreme

2 Answers

How do i remove and replace an key ignition on a 92 oldsmoble cutlass supreme....


Just a heads up, if you are changing the ignition due to security failure, there are other ways to fix this.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Apr 28, 2011 | 1992 Oldsmobile Cutlass Supreme

2 Answers

92 olds cutlass supreme turn signal broken


Start by checking the fuses that's simple
than relay than bulbs
last you may have to remove the steering wheel and than replace the entire signal assembly those are pretty much all your options so start with 1 and work your way down the list

Sep 24, 2009 | 1992 Oldsmobile Cutlass Supreme

2 Answers

The steeing column in my 95 Olds Cutlass


does the key have a computer chip built into it. i think it does . if this is the case that,s your problem. the key has to match the computer in the car it,s programed from the factory like this. you either have to use the original ignition lock and key or get the lock in your new column keyed to your original key by a lock smith. than your car will start. good luck.

Apr 18, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

My security light stays on in my 1994 Oldsmobile Cutlass Supreme. How do I fix this?


Replace the ignition lock cylinder or bypass the security system. The contacts are bad in the lock cylinder.

Mar 27, 2009 | 1984 Oldsmobile Cutlass

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...