Question about 1989 Volkswagen Golf

1 Answer

Just replaced feul pump ran good 2 weeks now started knocking like it ran out of oil but it has plenty. What could cause the knocking?

Posted by on

  • global1207 Nov 07, 2010

    DOES THE NOISE COMES FROM CRANK SHAFT AREA, OIL PAN AREA?
    DOES THE KNOCKING INCREASES WHEN ENGINES RPM GOES UP?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

I would check the actual oil pressure with a wet gauge. Locate the sending unit on top of the oil filter housing, remove the sending unit and install the wet gauge to check the actual oil pressure.

Posted on Nov 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004. Ran for a week, maybe 50 miles total, with oil light on, then came engine noise like a knocking. Oil level a bit high. What's wrong?


Likely head gasket failure. Oil level appears high because coolant is leaking into oil. This dilutes the oil causing the knocking. Oil usually looks brown or foamy when this happens. Park it now.

Dec 10, 2015 | Ford Transit Cars & Trucks

1 Answer

96 grand cherokee...no power to anything.


Look for a power relay in the fuse box under the hood.When you find it change it with another one in the fuse box that has the same part number on it.Make sure not to use the fuel pump relay.

Jan 20, 2012 | 1996 Jeep Grand Cherokee

1 Answer

My 2003 chevy silverondo feul pump stops working . have changed feul pump worked good for week and started doing it again. will start up again but who knows when


Did you replace the wire harness from the new sending unit to the frame??the old one tends to break when moved around causing issues and also inspect the ground wire also to ensure that it's still has a great ground on the frame from the harness.

The other thing also is that you may want to replace the fuel pump relay just to make sure it's now faulty. Just swap it out with another relay in the relay box.

Good luck and keep us posted.

Sep 05, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

We have a 2002 chevy Tahoe, 5.3 v-8 sometimes when we start it the gauges wont work for a minite or two, then they will just pop up, also it sometimes feels real sluggish with no power. the other day it...


The first problem about the gauges and lack of power is most likely the ignition switch.
On the 5.3 there is actually 2 knock sensors on this engine and they reside under the intake plenum on the engine, so you have to remove the intake on the engine to get at them. If your truck actually does have a serviceable fuel filter it will be on the frame somewhere under the drivers door area. if you don't see it then it is internal in the fuel tank and is part of the fuel pump assy and does not require replacement unless the pump goes bad.

Jun 30, 2011 | Chevrolet Tahoe Cars & Trucks

2 Answers

Engine knocks after starting and running after 2 minutes.oil guage dropped.let truck sit then started truck again ran for two minutes and started knocking bad.is this the oil pump and where is it located


yes it sounds like it,but check your oil too just to be sure ,your oil pump is in the oil pan take off oil pan u should see it,it will be on the sump end of the pan(caution) the oil pump on most vehicles are connected to the distributor so u might have to retime in eng after u do this,Hope this helps and good luck

Apr 05, 2011 | 2004 Ford F150

1 Answer

Have a 03 matrix with a oilpump promblem I think,bought the car last week ran good next day was drive on highway notice oil lap on and noise from motor ,slowed down light went off.Next day change oil and...


Generally three things can turn the light on. First is the sending unit itself if it's going bad. Next is an obstruction of the pump pickup screen (usually hard carbon deposits). Third is worn engine bearings (usually rod bearings). Best way to find the problem is to have someone put a mechanical pressure gauge on the engine and read the actual pressure. If it's low you need to go into the engine to determine why. if it's normal, replace the sending unit. Senders aren't terribly expensive and you could just buy one and replace the one you have, providing the engine isn't tapping or knocking.

Mar 14, 2011 | 2003 Toyota Matrix

1 Answer

2000 silverado 4.3 V6. Replaced feul pump and niw it starts but it takes 3-4 cranks in the morn to start it and then it runs very rough untill it has ran for 1/2 to 1 hr. Also have replace fuel filter...


The rough running should have caused the check engine light to come on. It would be a good idea to goa ahead and scan the engine for trouble codes. The rough running could be a number of things. The codes would help us pinpoint the correct part ot replace, rather than start replacing parts until we get lucky and hit the right one. That could be very expensive.

Jan 01, 2011 | 1999 Chevrolet Silverado 1500

5 Answers

Kia sedona. Knocking sound from Engine


You dont have a choice. if this is not handled it might make you loose this car totally. Consult an expert in your location to have a look at the cylinder.

Rate this.

May 29, 2009 | 2002 Kia Sedona

1 Answer

1992 GMC Sonoma - 4.3l cannot start after stall and knocking.


Sounds like an engine sensor, EGR valve or O2 sensor has failed. First thing to do is to look at the engine trouble codes to pin down the failure. You can usually borrow an OBD1 code checker from your local parts store.

Mar 11, 2017 | 1992 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...