Question about 1992 Lincoln Town Car

1 Answer

The motor runs, but does not operate the power window on the passenger side, front.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

I have same problem in my 1992 Lincoln town car? I wish to know the answer to this question to. Please someone help!

Posted on Aug 19, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Brian032472
  • 150 Answers

SOURCE: 2 dr honda accord power window problem

I wouls suspect you have either a inoperative window regulator (the frame work for the power glass) or a bad power window motor. More often then not the are sold as a single assembly and are not very hard to replace on this vehice.

Posted on Nov 02, 2008

  • 4 Answers

SOURCE: 2005 Chrysler Pacifica passenger doors have no power

If your alarm went off, it could be that someone had tried to break into your car. They most likely may have cut some of the wires inside your door with what ever device they may have been using. Look for evidence between the bottom of the windows and doors where the problem is. If not, then it is possible that your automatic window assemblies are malfunctioning. Do you hear the motors run on the windows when you go up or down with the switch? I also have a Pacifica, 2005, however no window problems yet.

Good Luck,

Ray

Posted on May 11, 2009

  • 462 Answers

SOURCE: passenger power window does not work 2002 Silverado HD Ext Cab

REMOVE THE DOOR PANEL TO GET TO THE WINDOW MOTOR. REMOVE THE CONNECTOR ON THE MOTOR. LOOP A TEST LIGHT FROM BOTH TERMINALS. WITH THE KEY ON AND BOTH SWITCHES IN PLACE, CHECK TO OPERATION OF THE SWITCHES. IF THE LIGHT COMES ON IN BOTH DIRECTION THE WINDOW MOTOR IS BAD.

THERE IS A CIRCUIT BREAKER BUILT INTO THE WINDOW MOTOR. SOMETIME HITTING THE MOTOR WITH MAKE THE CIRCUIT BREAKER RESET BUT THE MOTOR WONT LAST LONG DOING THAT.

ALSO TRY PULLING DOWN ON THE WINDOW WHILE TRYING THE SWITCHES. THE WINDOW COULD JUST BE STUCK. THIS HAPPENED TO ME.

Posted on Jun 18, 2009

Testimonial: "Thanks, BB1BUD. I ended up replacing the entire regulator with a part I ordered online. So far so good."

c17hydro
  • 2984 Answers

SOURCE: power window

Don't know what kind of car that you have but typically if it is an older vehicle or the usage of the window is high (u and down, up and down a lot) then the cable taht lifts the window is broken or the little plastic tab is broken that "grabs" or grips the cable to lift it. You have to replace the track assembly. You don't have to replace the motor though....you can unbolt it from the track.

Posted on Nov 11, 2009

  • 16 Answers

SOURCE: Power window (front passenger side) won't come

the motor that powers the window up and down may need to be replaced

Posted on Jun 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

Location of the power window relay in a 1998 cadillac eldorado


http://www.bbbind.com/free_tsb.html free wiring diagrams !
Left Front Power Window Switch
The battery voltage is applied from the WINDOWS circuit breaker through CKT 42 (RED) to the accessory time delay relay. The accessory time delay relay supplies voltage through CKT 70 (PNK) to the left front power window switch under the following conditions:
?€¢
The ignition is in the RUN position.


?€¢
The retained accessory power (RAP) is active.

When an UP switch on the left front power window switch is operated, the battery voltage is applied to the power window motor. The power window motor is grounded through the DOWN contacts of the left front power window switch to G204. The motor runs in order to drive the power window up. When a DOWN switch in the left front power window switch is operated, the battery voltage is applied to the power window motor in the opposite direction. The power window motor is grounded through the UP contacts in the left front power window switch to G204. The motor runs in order to drive the power window down.
Accessory Time Delay Relay
On the left front of the passenger compartment, taped in the body harness

Jun 18, 2016 | 1998 Chevrolet Cavalier

1 Answer

My power seats and only the power windows on right side quit working on my 2007 silverado classic lt1500 I replaced the circuit breakers already and it did not fix the problem


Does you truck have Memory Seats ? There are 2 options of power seat systems available in full size trucks. The first is 6 way driver and passenger power seats without memory. The second is an 8-way driver seat plus 4-way lumbar with memory, heat and optional cool function.
If you replaced the circuit breaker , did you check for B+ voltage at the switch ? If you have memory seats there is a control module that is in the mix.
For the power windows same thing here ,the BCM - body control module is involved .A factory Tech 2 scan tool is still the best tool to use ,checking data parameters .
The switch for the front passenger power window has 2 positions UP and DOWN, and it's position is a direct input into the PDS. Upon receiving a request for power window operation (switch activation), the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to drive the window UP or DOWN.
The front passenger power window can also be operated from the driver master control. The front passenger window switch on the driver master control has 2 positions UP and DOWN and it's position is a direct input into the DDS. Upon receiving a request for front passenger power window operation, the DDS transmits a GMLAN message indicating the changed switch position. When the PDS receives this message, the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to move the window UP or DOWN.
GMLAN - is a data bus communication network that vehicle modules talk together on.
Rear Passenger Power Window Operation (RPO A31/AN3/DL3)
The body control module (BCM) monitors the window UP/DOWN command from the DDS. When the rear window UP or DOWN command is received, the BCM sends a signal to the appropriate rear window switch. The rear window switches continuously monitor the up and down signal circuits, if no function is being commanded, the signal voltage is at approximately B+ voltage. If the UP or DOWN function is commanded, the BCM signal voltage drops approximately 5 volts and the appropriate rear window switch will then command the window in the UP or DOWN direction.
Your best bet would be to take your truck to a GM dealer !
Your best bet

If

Nov 04, 2015 | Cars & Trucks

1 Answer

2003 cadilac deville driver window off track. motor seems to work but window will not go up.


Window regulator is bad in the drivers door . Do you know what a regulator is ? The Trainer 24 Power Window Troubleshooting Do you know anything about automotive electrical testing ? How to read an use a wiring diagram ? Do you know there are two side to a electrical circuit ? B+ voltage an a ground side . Plus there is electronic control modules and class 2 serial data network involved . When you push the switch for a window othen then drivers window on the drivers door . a class 2 message is sent to the other doors modules . The correct module will then open it's window .
http://www.bbbind.com/free_tsb.html Check out free wiring diagram here .Enter vehicle info . year , make , model and engine size. Under system click on body & accessories , subsystem click power windows . Click search button , then click each link one at a time .

Mar 27, 2017 | 2003 Cadillac Deville

1 Answer

Power window on paassenger side front won't let


NEED TO CK IF THERE IS POWER TO THE SWITCH, CK IF SWITCH IS LOSE , INSIDE DOOR PANEL ,CK WINDOW MOTOR,RUN IT DIRECT TO TEST THAT THE MOTOR IS IN RUNNING CONDTION ,

Oct 26, 2009 | 1989 Buick Century

6 Answers

Windows won't roll down


Does the rear window work from the passenger switch?

Oct 07, 2009 | 2003 Cadillac CTS

1 Answer

All windows but drivers won't go up or down 2001 GMC yukon


If they sound like they are trying to do something it's not the lock out switch . But to be sure pulling out the switch an testing for B+ voltage to and from the switch . Plus pull the other door switches to see if they have B+ voltage and good grounds would be the thing to do.. If you don't know how to check automotive electrical circuits your best bet , take it to a qualified repair shop .
Passenger Power Window Operation
The passenger power window switches incorporate window up and down relays. The relay coil feed and supply sides are powered through the RAP fuse supply voltage circuit. The normally closed contacts of each relay is connected to ground. The load side of each of the relays are connected to either side of the power window motor through the power window up and down circuits. The up and down relay control circuits are connected to the normally closed contacts of the passenger window switch. These contacts are wired in series with the power window master switch, through the power window master switch up and down signal circuits and then to ground when the power window master is placed in the up or down position. This allows for the up and down operation of the passenger power window from the power window master switch. The center pole of the passenger power window switch is also connected to ground and will energize the relay when placed in the up or down position.

Driver Power Window Operation
The driver power window is unique from the passenger power windows in that it does not use window up and down relays. The driver power window is operated directly from the power window switch.
The normally closed contacts of the switch are connected to ground and the center pole is connected to the RAP fuse supply voltage circuit. By placing the left power window switch in the down position, voltage is applied to the power window motor left front down circuit and to the power window motor. The other side of the power window motor is connected to ground through the normally closed contacts of the left power window switch through the power window motor left front up circuit and drives the window down.
By placing the left power window switch in the up position the polarity of the motor is reversed and the motor drives the window up.

Has circuit breaker for B+ power
• PWR WDO CB 25A (fuse block) (System power for left and right windows 2-door vehicles. System power for LF and LR windows 4-door vehicles)
• PWR WDO CB 25A (IP wiring harness junction block) (System power for RF and RR windows 4-door vehicles)

Could be passenger door switch .

Aug 21, 2017 | 2001 GMC Yukon XL

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

2 Answers

THE POWER WINDOWS ON THE DRIVER'S SIDE OF MY 99 EUROVAN CAMPER DO NOT OPERATE. THE WINDOW ON PASSENGER SIDE OPERATES NORMALLY FROM PASSENGER SIDE, BUT WILL ONLY GO DOWN WHEN ATTEMPT MADE TO OPERATE IT FROM...


This is essentially correct. A common problem with earlier models of Eurovans is the wiring through the door boot. Check this first as the wires tend to become brittle and break. This can save you alot of hassle in getting the door panel off and inspecting the motor mechanism. A good sign is if when you press the window switch you hear a little "click" in the right front of the dash. That is the window relay engaging. Power is getting to that point in the circuit but can't make it back through to the door.
Mike

Jan 25, 2009 | Volkswagen Eurovan Cars & Trucks

Not finding what you are looking for?
1992 Lincoln Town Car Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...