Question about 1989 Toyota Camry

1 Answer

Timing belt timing marks replacement procedure

Posted by on

  • Anonymous Jun 16, 2008

    how do i stop engine from turning when i remove crankshaft bolt

×

1 Answer

Use a pipe mounting plate and insert long bolts through the plate and the drive pulley. use a pipe wrench to fix the rotation against the car body. then use a 19 mm hex socket to break the mounting bolt loose. may require a large handle 1/2 inch socket wrench as the mounting torque is about 100 foot pounds. reverse the pipe wrench when tighting the crankshaft bolt.

Posted on Jul 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset timing marks after replacing a broken timing belt?


Land Rover Freelander 2002-2005 KV6 Timming belt and ...

? 4:31
https://www.youtube.com/watch?v=sz_oe9tIFH4
Jul 3, 2011 - Uploaded by Jaime Depaula
Land Rover Freelander 2002-2005 KV6 Timming belt andreplacing valves - Video 2 ... shops in North Eastern USA for bent valves and timing belt change? .... Land Rover 200tdiTiming Belt -From Broken Belt to Retiming the ...

ROVER K Series Cambelt Change Video - YouTube

? 10:52
https://www.youtube.com/watch?v=1Qn8ljQKZxA
May 4, 2012 - Uploaded by metalworker007
How to change a rover K series cam belt .. by Technozen of ...soy espa?ol porfavor quiero saber timing marks de MG ROVER 25 petrol 1795cc engen .... Hi, Have a Land Rover Freelander1999 petrol serie K, that dont start, ...

Freelander 1.8i timing belt - Land Rover Technical Archive - LR4x4 ...

forums.lr4x4.com > ... > Tech Archive > Land Rover Technical Archive

Nov 20, 2006 - 1 post - ‎1 author
The following is instructions for replacing the timing (or camshaft) belt on the 1.8i petrol engine, as fitted to a Freelander. This is the K-series ... With the timing set, thecam sprocket marks should look like this. Posted Image

How to Replace timing belt on Land Rover Freelander 2.5 ...




Dec 10, 2015 | 2002 Land Rover Freelander

2 Answers

Problems of gm


You can rotate the cam/crank into a positon that will not move as you remove the old belt, as long as the new belt places the cam/crank in same position as the old belt had them, it don't matter where the timing marks are. Leave your old belt on, rotate to a position that will not move or have tension on belt, (no matter the marks) and replace the belt. Make sure to recheck timing marks after new belt is installed by rotating the crank/cam back to timing marks, or just trust that the belt was replaced without the cam or crank rotated. Easy off, easy on, just make sure the cam/crank are still in time as the old belt had them located. NOTE: timing marks are there in case of a broke belt, or for a car that has jumped time. As long as cam and crank are held in same positon, and car was in time before the procedure, it don't matter where the timing marks are at during belt replacement.

Dec 15, 2013 | Cars & Trucks

1 Answer

2001 murcury cougar 2.0 vct 4cyl timing belt replacement


You probably need to get a good repair book or a copy of a shop manual. The procedure is to mark the gears before you remove the belt. I counted 26 steps from start to finish if you mark the gears.

Jul 05, 2013 | Cars & Trucks

2 Answers

Kia sedona instructions to replace serpintene belt


Hi, Here is the procedure for a 2002 KIA Sedona 2.9, Engine code KJ. I I can not guarantee the followingprocedure is exactly the same as your car.

Warnings and recommendations Unless otherwise advised by the manufacturer, the following procedures are recommended: Always fit a new timing belt after removal Check the tensioner and idler pulleys; renew if necessary Never turn the engine in the direction opposite to that of normal operation Check the belt(s) for cracks, fraying, wear and oil contamination Note: The engine must be cold before timing belt adjustment Note: Avoid bending, torsion or traction General Before disconnecting the battery cable, check the audio system security code kj_t_dba_uk_6.jpg
Always check the timing marks before timing belt removal Removal Disconnect the battery Remove the radiator upper hose Remove the fuel filter unit Note: Do not disconnect the hoses carniv_j3tci_t_dba_uk_3.gif
Remove the engine mount kj_t_dba_uk_4.gif
Remove the bracket Remove the right front wheel Remove the air-conditioning drive belt Remove the ancillary drive belt Remove the ancillary drive belt tensioner Remove the coolant pump pulley Remove the crankshaft pulley Remove the timing cover(s) kj_t_dba_uk_6.jpg
Align the timing marks Loosen the tensioner kj_t_dba_uk_7.gif
Remove the tensioner Remove the timing belt Check the gearwheels, tensioner and idler pulley(s) for damage and wear Renew if necessary Installation kj_t_dba_uk_6.jpg
Check the timing marks Fit the timing belt kj_t_dba_uk_7.gif
Fit the tensioner kj_t_dba_uk_3.gif
Adjust the tensioner kj_t_dba_uk_1.gif
Align the marks on the tensioner Tighten the tensioner (23.5 Nm) Rotate the engine 2 rotations by hand kj_t_dba_uk_6.jpg
Align the timing marks kj_t_dba_uk_8.gif
Check the tensioner Repeat the procedure if required Refit the timing covers Refit the crankshaft pulley (373 - 392 Nm) Refit the coolant pump pulley (17.6 - 28.4 Nm) Fit the ancillary drive belt tensioner Fit the ancillary drive belt Refit the air-conditioning drive belt Refit the front right wheel (88 - 108) kj_t_dba_uk_4.gif
Fit the bracket (36.2 - 53.9 Nm) Refit the engine mount carniv_j3tci_t_dba_uk_3.gif
Refit the fuel filter unit Refit the radiator hose(s) Refill the cooling system Check for leaks Reconnect the battery earth cable Torque settings Tensioner: (23.5 Nm) Timing covers (6.9 - 9.8 Nm) Coolant pump pulley: (17.6 - 28.4 Nm) Special tools Special tools are not required

Jan 06, 2013 | 2004 Kia Sedona

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

1 Answer

Need diagram for timing marks for timing belt


You need a repair manual. Try Haynes. There are
timing marks on the camshaft and crankshaft sprocket.
I'm assuming you are replacing the timing belt and the
procedure requires the manual.

Dec 29, 2010 | 1998 Honda Civic

4 Answers

Need diagram to replace timing belt on 2000 dodge intrepid 3.5 engine


I Show Only a 3.2L For this Year this Will Guide you Enjoy your Work RejakWilson


REMOVAL

CAUTION: The following procedure can only be used when the camshaft sprockets HAVE NOT BEEN LOOSENED or removed from the camshafts. Refer to Camshaft Gear/Sprocket and Timing Components, if sprocket(s) or camshaft(s) have been loosened or removed.

CAUTION: The 3.2/3.5L are NOT freewheeling engines. Therefore, care should be taken not to rotate the camshafts or crankshaft with the timing belt removed.

  1. Disconnect negative cable from remote jumper terminal.
  2. Remove upper radiator crossmember.
  3. Disconnect fan module electrical connector.
  4. Remove cooling fan module and accessory drive belts.
  5. Remove crankshaft damper and front timing belt covers.
  6. Mark belt running direction, if timing belt is to be reused.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.

f90f2f1.gif Fig. 94

  1. Rotate engine clockwise until crankshaft mark aligns with the TDC mark on oil pump housing and the camshaft sprocket timing marks are between the marks on the rear covers (Fig. 94).
CAUTION: Align the camshaft sprockets between the marks on rear belt covers before timing belt removal or damage to valve and/or pistons could occur.

  1. Using a ink or paint marker; mark the exact position of the camshaft sprocket timing mark relative to the two timing marks on the rear timing cover.
NOTE: When timing belt tensioner is removed from engine, always store in the vertical (plunger facing upward) position

09766f9.gif Fig. 95

  1. Remove the timing belt tensioner (Fig. 95) and remove timing belt.
TIMING BELT TENSIONER

  1. When tensioner is removed from the engine it is necessary to compress the plunger into the tensioner body.
CAUTION: Compress the tensioner slowly, as damage to tensioner could result.

c719a3d.gif Fig. 96

  1. Place the tensioner into a vise and SLOWLY compress the plunger (Fig. 96). Total bleed down of tensioner should take about 5 minutes.
CAUTION: Index the tensioner in the vise the same way it is installed on the engine. This is to ensure proper pin orientation when tensioner is installed on the engine.

  1. When plunger is compressed into the tensioner body install a pin through the body and plunger to retain plunger in place until tensioner is installed.
NOTE: When timing belt tensioner is removed from engine, always store in the vertical (plunger facing upward) position.

INSTALLATION

CAUTION: This procedure can only be used when the camshaft sprockets HAVE NOT BEEN LOOSENED or removed from the camshafts.

CAUTION: If camshafts have moved from the timing marks, always rotate camshaft towards the direction nearest to the timing marks (DO NOT TURN CAMSHAFTS A FULL REVOLUTION OR DAMAGE to valves and/or pistons could result).

a7cd673.gif
Fig. 97

  1. Align the crankshaft sprocket with the TDC mark on oil pump cover (Fig. 97).
  2. Align the camshaft sprockets (to reference mark made upon removal) between the marks on the rear covers (Fig. 94).
  3. Install the timing belt starting at the crankshaft sprocket going in a counterclockwise direction (Fig. 97). Install the belt around the last sprocket. Maintain tension on the belt as it is positioned around the tensioner pulley.
  4. Holding the tensioner pulley against the belt, Install the tensioner into the housing and tighten to 28 Nm (250 in. lbs.) . Each camshaft sprocket mark should still fall between the cover marks.
  5. When tensioner is in place pull retaining pin to allow the tensioner to extend to the pulley bracket.
  6. Rotate crankshaft sprocket 2 revolutions and check the timing marks on the camshafts and crankshaft. The marks should line up within their respective locations (Fig. 97). If marks do not line up, repeat procedure.
  7. Install timing belt covers and crankshaft damper.
  8. Install accessory drive belts and cooling fan module.
  9. Install upper radiator crossmember.
  10. Connect negative cable to remote jumper terminal.
  11. Start engine and allow to idle for approximately 1 minute. If a noise is present from the timing belt/tensioner, air has possibly entered the tensioner.
    1. To remove air from tensioner; using a DRB III, operate the engine at speed of 1600-2000 RPM for 10 minutes. This will purge air from tensioner.
NOTE: If air is present, the timing belt tensioner will be soft and may generate noise. This noise should disappear after no more than 15 minutes of engine running time.

Oct 21, 2010 | Dodge Intrepid Cars & Trucks

2 Answers

Marks for 97 toytoa camry


Timing Belt "Marks"?
CLICK on the following LINK. It has the Timing Belt Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1997/make/toyota/model/camry/1997_toyota_camry_timing_belt_diagram_marks.htm

Feb 27, 2010 | 1997 Toyota Camry

1 Answer

Replacing the timing belt on a 1998 Nissan Quest and need to know cam shaft and crank shaft positions.


go here for expert help on Villager & Quest

http://groups.yahoo.com/group/villagerquest/

e09cf57.gif

Item Part Number Description 1 — 40 Timing Chain/Belt Teeth 2 6256 Camshaft Sprocket , Front 3 — 43 Timing Chain/Belt Teeth 4 6306 Crankshaft Sprocket 5 6268 Timing Chain/Belt 6 6256 Camshaft Sprocket , Rear
Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301) .
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592) .
  1. Remove the main wiring harness from the upper engine front cover (6019) .
  1. Remove the eight upper engine front cover bolts and the upper engine front cover .
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775) .
  1. Use Strap Wrench 303-D055 (D85L-6000-A) or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501) .
  1. Remove the crankshaft pulley (6312) . Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover .
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
  3. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.
  4. Loosen the timing chain/belt tensioner nut.
  5. Remove the timing chain/belt .

  6. Installation
    NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned. NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts (6250) and the crankshaft (6303) . These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket .

    NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600) .

    Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprocket following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner .





Sep 20, 2009 | 1998 Nissan Quest

2 Answers

Timing belt replacement


This is the timing belt replacement procedure to 1999 Vovlo V70
with the B5254s engine

1) Lift power steering and anti-freeze resevoirs slightly and disconnect electrical connector for antifreeze sensor. Then carefully lift both resevoirs and position it on top of the valve cover.

2) Relieve the tension from the serpentine belt tensioner pulley and remove the serpentine belt.

3) Remove the screw holding the plastic timing belt cover and carefully remove the cover.

4) Locate the timing marks on the camshaft pulleys. I highlighted the marks with paint to make them easier to see. I took a dab of white touch up paint and put it on each mark, then waited a minute and then wiped the excess paint carefully, leaving a white line for the mark. The mating marks for the cam gears is on the upper cam gear cover. The marks are rectanular cutouts on the underside of the cover. I was unable to line up the marks unless standing on my head so I extended the marks to the outside of the cover with a white painted dot. This trick made life much easier.

5) Reinstall the timing gear cover.

6) Place a 32mm socket on the crankshaft pulley and connect a breaker bar to the socket. Slowly rotate the engine crankshaft (clockwise) until the camshaft timing marks are aligned with the marks on the gear cover. (I preferred to do this job with the spark plugs installed. I found it easier to keep the engine in time by using the engine compression).

7) Remove the vibration damper by removing the 32mm nut and remove all of the 10mm screws. Carefully pry the pulley from the shaft. There is an alignment pin which allows the pulley to be installed only one way. With the vibration damper removed you can now check the timing alignment with the crankshaft and it's witness mark.

8) Remove the small timing belt shield from the underside of the crankshaft. This shield is helt in place with 2 screws.

9) Loosen the ttiming belt tension and remove the old timing belt.

10) This is a good time to check the waterpump for any signs of wear or leaks. Mine was leaking after 101,000 miles. I also replaced the tensioning pulley and used Volvo OEM parts. (The old Volvo parts lasted 100,000 miles, that is good enough for me).

11) Reverse the procedure for installing the new timing belt.

12) After the belt is installed and properly tensioned, put the breaker bar with the 32mm socket onto the vibration damper and rotate the engine (clockwise) slowly until your timing marks are again aligned. If they are not, remove and reinstall the belt. Don't get frustrated just think of all of the money you have saved by doing this job yourself.

dbea7d9.jpg68d3133.jpg

Aug 10, 2008 | Volvo 740 Cars & Trucks

Not finding what you are looking for?
1989 Toyota Camry Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...