Question about 1994 Ford Mustang

Open Question

Where is the crank sensor located on my 94 mustang 5.0

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

brandyspoile
  • 61 Answers

SOURCE: Crank Sensor in 94 Isuzu Rodeo

it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Posted on Jul 24, 2009

emissionwiz
  • 75807 Answers

SOURCE: speed sensor removal 94 Mustang GT

Remove the trans cross member and let the trans drop down (use a floor jack), then you will be able to access it.

Posted on Sep 23, 2008

  • 14036 Answers

SOURCE: Where is the crank sensor

look on the left side midway lower botom.

Posted on Apr 20, 2009

techbuster
  • 5081 Answers

SOURCE: Location of crank sensor on 94 Nissan Pickup 4cyc

It is located in the distributer. The part is not sold seporate from the distributer. It is only a dealer item the whole distributer for 450.00$. It is also called the crank angle sensor. Just because the code 0335 comes on on the scan does not mean that the sensor is bad. The best thing to do it take it to a dealer.
Actually the one in the distributor is called a camshaft position sensor. You can by rebuilt distributor for around 250.00. The crank shaft position sensor is located on the Transmission housing on the left side.

Posted on Nov 17, 2009

c17hydro
  • 2984 Answers

SOURCE: wheres the crank shaft sensor located on 94

Do you have a 2.3L, 2.4L, or a 3.0L?

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 mustang gt will not start new timing chain dose anyone know what I can do/help


assuming that you got the valve timing right ,the next point is have you got the ignition timing right on the correct stroke (not 180 degrees out)
next have you reset the ECM to operate the immobiliser. Are all the crank/cam sensors connected.

Feb 13, 2015 | Cars & Trucks

1 Answer

Where do i locate the crank sensor on a 1992 mustang 5.0


the '92 doesn't have a crank sensor - the distributor is geared directly to the crankshaft. Usually only cars that have coilpacks (vs traditional distributors) have crank sensors.

Sep 28, 2011 | 1992 Ford Mustang

1 Answer

My speedometer wont work nor trip gage on 94 MUSTANG


it sounds like the speedometer cable is unhooked.

Apr 04, 2010 | 1994 Ford Mustang

2 Answers

Crank Sensor in 94 Isuzu Rodeo


it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Jul 13, 2009 | 1994 Isuzu Rodeo

1 Answer

94 mustang gt has no spark . i just installed a new engine had it running and was adjusting the timing when the car stalled. Now i have no spark. Any idea what to look for??


Check and test the coil making sure you have power to the coil, using the 12v test light. If you are getting juice, check distributor and rotors and all plugs wires. no juice, now you have to trace back why you not getting power to the coil, also check the crank position sensor,making sure is in working condition. Crank sensor sense the turning of the crank and send the message to the computer, telling computer to send the single to the coil telling it to disperse the charge from the coil to distributor. If crank sensor is good than it will be computer. Hope that help some..remember, if you adjust timing by rotating distributor, make adjustment in 1.00 mm at a time. anymore you can be out of timing.

Jul 05, 2009 | 1994 Ford Mustang

2 Answers

I am getting fuel to the rail but my 94 3.8L mustang still wont start?


DID YOU CHECK YOUR CRANK SENSOR OR YOUR NEUTRAL SAFETY SWITCH

Apr 23, 2009 | 1998 Ford Mustang

1 Answer

How to install new sensors on Mustang 1997?


my 94 mustang air bag lite bleeks and i do not no why

Apr 03, 2009 | 1997 Ford Mustang Cobra

1 Answer

Speed sensor removal 94 Mustang GT


Remove the trans cross member and let the trans drop down (use a floor jack), then you will be able to access it.

Sep 23, 2008 | 1994 Ford Mustang

Not finding what you are looking for?
1994 Ford Mustang Logo

Related Topics:

467 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...