Question about 1998 Isuzu Rodeo

1 Answer

I own a 1998 holden rodeo diesel 4x4 all my lights work except my brake lights. all my fuses are fine and both globes are ok as well

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 395 Answers

It sounds like the brake light switch has failed. It is located on a bracket under the dash near the top of the brake pedal arm. You could put a bridging wire across the terminals to confirm if the switch is out and the rest of the wiring is OK. If the lights then work replace the switch.

To remove switch, disconnect wiring, loosen locknut and unscrew switch. Replacement is reverse procedure. To adjust, screw in switch until operating button is fully depressed by pedal arm, tighten locknut and reconnect wires. Check for correct operation of lights.

Posted on Nov 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blowing brake fuse as soon as it touches, the only thing that stops it blowing is pulling a plug from the bcm, not sure if im just pulling power to the bcm or whether theres a bcm fault???


Hi Steve Is this a new fault has it just started to occur for no reason. You need to start with the basics i.e. have you recently replaced any globes? not necessary brake light globes ,If you have re check it make sure its the correct one,(check it against the other side). make sure it's not fitted incorrectly upside down. remove it and try brake lights again. Move onto your brake lights remove eye level globe and brake light globes left and right now try brake lights does it still blow fuse if not check all globes, connections and local brake light wiring for any shafing. Fit each globe one by one if it blows again remove that globe and try the others, Do you have tow bar and electrics fitted Check and make sure wiring in or around the socket has not come adrift and shorting out the brake light circuit. If all the above fails get it inspected by a Dealer or auto electrician, as the fault may be a lot more involved. Preferably a dealer as they will have the correct information on your vehicle. Good luck

Jan 11, 2018 | Holden Cars & Trucks

1 Answer

Where do I locate the relay/flasher unit in a 2001 diesel Holden Rodeo to replace it?


IF the flasher works at all, it is not the flasher. They blink faster than normal when there is a wiring short.

Nov 08, 2014 | Cars & Trucks

1 Answer

Headlights wont work on 1998 mustang v6 Running lights brake lights and gauge lights work fine. The lights only trn on when i hold the high beam switch. Any suggestions?


check fuses and check globes . Globes might have two filaments and low beam ones has blown . Had this globe thing happen on two globes at the same time on Ford Falcon's Halogon globe headlights.

May 05, 2014 | Cars & Trucks

1 Answer

Vt holden commodore brake lights dont work


There could be a couple of reason why your brake lights are not working these are all common faults.

1.first remove the brake lens and check globes.
2.Next check the globe socket as they tend to get hot and the plastic housing brakes away so the globes don't connect.
3.get a test light and check for power.
4.if everything is ok then I would be replacing the brake light switch under the dash that makes contact with brake pedal.

good luck

Nov 09, 2013 | Cars & Trucks

1 Answer

Holden captiva lx brake lights not working


It is common for the plastic brake light switch to get jammed or brake. Remove and make sure small centre rod moves. To remove just turn and release light a light bulb. If switch fails it will prevent brake lights and can also prevent gear selector to move and also make brake pedal feel spungy.

Feb 28, 2012 | Cars & Trucks

1 Answer

All my lights work except my brake lights. all my fuses are fine


the brake light swicth is at the top of brake pedal remove wires from swicth and brigde together if lights work replace swicth

Nov 07, 2010 | 1998 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14406 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...