Question about 2001 Toyota Sequoia

Open Question

How to replace alternator fuse on 2001 toyota sequoia

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 255 Answers

SOURCE: warning lights/2001 Toyota Sequoia ltd

sensor wire were not reinstalled in brake job take it back get it right

Posted on Apr 13, 2009

  • 1986 Answers

SOURCE: replacing tail light bulbs on 2001 Toyota Sequoia

Remove the two screws holding the tail light cover in place along the edge of the tail light assembly.

After you remove the two screws in the back panel, you have to pull the assembly out towards the side of the vehicle. You cannot pull it straight back from the trunk or you will break the pins that hold the lens cover onto the side of the SUV.

There are two pins that allow the light cover to be secured against the back of the truck. One pin is towards the top, the other pin is towards the bottom.

Twist out the bulb assembly.
Pull out the bulb
Insert the new bulb
Twist back in the bulb assembly
Place the pins over the pin holes in the light cover mold on the side of the truck
Push in gently Replace screws and you are done.

Posted on Nov 02, 2009

  • 215 Answers

SOURCE: how do I replace brake rotors on a 2001 toyota

remove the tire, there should be two bolts holding the caliper on, remove these two bolts, the caliper will be able to slide off and out of the way, the rotor should be able to come off, or you will have to give it a few taps, remove the old one, make sure you have the proper rotor, and place it on the hub, the brake pads should be replaced at this time, the pads will pop out easily, now you will have to compress the piston with a C clamp and one of the old brake pads, once the piston is back in place the new pads can be snapped into place and now the caliper can go back on and tighten the two bolts, put the tire back on.

Posted on Nov 03, 2009

  • 136 Answers

SOURCE: 2001 Toyota 4runner Limited Alternator belt broke.

simple really 12mm wrench an socket and 14 mm wrench an socket. lossen alt bracket 14mm then tesioner 12mm slide back drop belt and reverse. unless condensioner belt in way then dro 12 mm bolts on shiled then back off 12mm bolts on condensioner pulley remove belt follow previous instructions

Posted on Nov 25, 2009

duane_wong
  • 6826 Answers

SOURCE: 2001 Toyota Sequoia is showing a P0505 and PO420

P0505 Idle Control System Malfunction

IACV or Idle Air Control Valve if equipped is malfunctioning.

P0420 Catalyst System Efficiency Below Threshold (Bank #1)
The Catalytic converter is not working up to par in Bank#1.

I think this will point you in the right direction..



Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 toyota sequoia main tail light relay location


I had an S-10 pickup that had a tail light out. It had two fuse panels one inside the cab and the main one under the hood. They had a fuse for each tail light and it was in the main fuse box under the hood. You'll need a way to check your fuses if you can't see witch one is bad. They were very small fuses in my S-10. Hope this helps

Sep 10, 2014 | 2001 Toyota Sequoia

1 Answer

Torque settings for serpentine belt tensioner and pulley - 2001 Toyota Sequoia?


You actually have a torque wrench

I would just tighten down good

Oct 02, 2012 | 2001 Toyota Sequoia

1 Answer

2001 Toyota Sequoia Oxygen sensors


No the wires won't likely be the same length

The front upstream sensors, are not the same
Part # as the rear,downstream monitor sensors

Go to Rock Auto.Com & look up your oxygen sensors
I would get the NTK or Bosch,if they have that

You do not replace the rear sensors, until they fail

You replace the front ones at 100,000 miles or sooner,
if they fail

Jun 02, 2012 | 2001 Toyota Sequoia

2 Answers

Head lights dont come on. 2001 toyota Sequoia


To test relay just replace it with another similar relay with same spade configuration and turn the lights on, normally it's the multi function switch that goes bad, If you try a different relay and the lights don't come on then it is the switch. If you need some more help just answer the e-mail so I can give you more detailed information on testing.

Dec 29, 2009 | 2001 Toyota Sequoia

1 Answer

My 2006 toyota sequoia has no dash lights for the most part and the cigarette lighter does not work. The clock works but no radio lights either. The radio works.


My 2001 Toyota Sequoia just lost all dash lights last night too. I've tried checking the fuses in the cabin, and none of them look blown. Did you ever get an answer to this problem?

Sep 03, 2009 | 2006 Toyota Sequoia

2 Answers

My rear hatch door handle broke i need to replace it. how do i replace it?


how do i get the rear gate panel off so I can replace the latch on the 2003 sequoia.

Jul 06, 2009 | 2002 Toyota Sequoia

2 Answers

2003 rear door latch broken how do I get the panel open


if the door is shut, it is a real doozy but i have done it. you have to pry the inner panel off the door using hook tools and small, crowbar shaped tack pullers....kinda like a mini wonder bar. once the panel is off, you have to fish around inside the door and pull the cable on the latch by hand.

Jun 29, 2009 | 2001 Toyota Sequoia

2 Answers

Rear door latch replacement 2003 sequoia


Fig. The latch bracket shown is moved by loosening the mounting fasteners and sliding it as necessary. Matchmark the bracket to the door pillar before moving-1.8L Passat model shown

Jun 02, 2009 | 2003 Toyota Sequoia

1 Answer

Hopsean1


Are you using a Genuine Toyota replacement fuel pump? If not, get the Toyota part. "Aftermarket" pumps have been known to quit for no reason, I have observed this a few times.

Sep 22, 2008 | 2001 Toyota Sequoia

Not finding what you are looking for?
2001 Toyota Sequoia Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...