Question about 2002 Oldsmobile Silhouette

1 Answer

OBD II , will not show any reading, power windows l/r do not work,Acessory position of key switch does not work,Air suspension Not working ,Have checked All fuses in cab ,under hood ,,,,have been looking for a relay (RAP} acessory time delay . am unable to visually find it , not 100% this is the source of the problems. not sure exactly sure even what it looks like nor where it is located , Nor where to find one .BumFugled Wade , any help Would be apprecated.

Posted by on

  • trashguru1 Nov 07, 2010

    I forgot to mention , it does start ,

  • trashguru1 Nov 12, 2010

    Duane, i apologize for the late response, Yes, it starts runs, I was told the cigarett power outlet fuse is prob blown ie" no obd reading power, i am going to check again, to see if this could have been one i possably missed, then i guess it should read , with all the other non working circuts . acc Key position not working, along with all the rest . if this doesn't work ,to confirm the computer ,i will have no choice , but to order one. Thank you, I will get back to You, Wade

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 6,826 Answers

If the car starts and runs, but the OBD II will not communicate with the scanner, the computer is bad.

Posted on Nov 07, 2010

  • Duane Wong
    Duane Wong Nov 12, 2010

    Sounds like a bad computer or the wiring to it.

  • Duane Wong
    Duane Wong Nov 12, 2010

    Try a used computer not new for economic reasons. On a 2002 it's 8 years old, maybe someone has a used one in a car that has been wrecked that you can obtain for less than a new one.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003biuick crv I cant read the computer.what can I do ?


You have to be able to test for power going to the scanner off of the OBD II plug ur missing positive or ground u can test it by using digital meter that is computer safe or test light that is computer safe one of the prawn should show positive and one should show negative see what is missing and supply to operate and test. Don't forget to test the fuses.
Good Luck

Dec 22, 2016 | Cars & Trucks

3 Answers

SERVICE VEHICLE LIGHT SOON


turn the key to the on position. press the gas pedal 3 times within 5 seconds. if it doesn't work. turn the key off than back to the on position and press the gas pedal 8 times with 8 seconds. Hope this helps you

Jun 23, 2014 | 2002 Buick Rendezvous

1 Answer

95 jeep grand cherkee clicking noise passenger side under dash radio won't come on while car is running or key in start position but will in acessory position also interior lites blink while car i


try this.. disconnect the vehicle battery entirely, connect a 10 amp battery charger to the car connectors matching the terminal leads..and power the car with the charger..you should hear a hum or buzz in whichever relay or circuit breaker is bad.. replace this relay and the lights and stuff should work..the charger will not direct-short but the guage may go full over indicating a malfunction..or extreme load.. maybe a window switch might be fried..you should be able to hear any issues as long as power is coming from the charger only...repost findings..

Jan 27, 2013 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Windows on my 1999 buick century do not work when the key is in the run position neither does the radio but they both work in the acessory mode


Based on your statement I would say the key switch is faulty.
The switch is mounted behind the key lock in the steering column.

Jul 06, 2012 | Cars & Trucks

1 Answer

2003 LINC TOWN CAR INTERMITTENT AIR SUSPENSION



For OBD code problems check the list of help links below. Click the link below to go through its procedure.

--------------
Diagnostic Code P2195? http://schematicsdiagram.blogspot.in/2012/02/diagnostic-code-p2195-on-toyota-avalon.html

--------------
Diagnostic code P1330? http://technoanswers.blogspot.in/2012/02/diagnostic-code-p1330-on-kia-2wd.html

------------
Diagnostic code P0700, P1330, P1121? http://technoanswers.blogspot.in/2012/02/diagnostic-code-p0700-p1330-p1121-on.html

-------------
shows error code P1330? http://technoanswers.blogspot.in/2012/02/2003-kia-sorento-shows-error-code-p1330.html

--------
OBD code P1330? http://technoanswers.blogspot.in/2012/02/obd-code-p1330-on-2003-kia-sorento.html

------------
OBD code P01300? http://technoanswers.blogspot.in/2012/02/obd-code-p01300-on-toyota-rav4.html

--------------
OBD code P0768? http://repairhelpcenter.blogspot.com/2012/01/obd-code-p0768.html

------------
Evaporative Emissions System codes details? http://schematicsdiagram.blogspot.com/2011/11/evaporative-emissions-system-codes.html --------------- Engine Misfire codes?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html

----------------


Misfire on cylinder 4?

http://schematicsdiagram.blogspot.com/2011/12/misfire-on-cylinder-4.html

--------------
ABS trouble codes for all models?

http://repairhelpcenter.blogspot.com/2011/11/abs-trouble-codes-for-all-1994-00-acura.html

------------
Diagnostic code P0010? http://schematicsdiagram.blogspot.com/2011/12/diagnostic-code-p0010.html

-------------
Diagnostic Code P1396?

http://howtobyme.blogspot.com/2011/11/diagnostic-code-p1396.html

--------------
Code P0452?

http://howtobyme.blogspot.com/2011/11/code-p0452.html

-------------


OBD code P0172 on Buick?

http://howtobyme.blogspot.com/2011/11/obd-code-p0172-on-buick-park-avenue.html

-------------
DTC Code P0321?

http://howtobyme.blogspot.com/2011/11/dtc-code-p0321-on-buick-park-avenue.html

------------------


Error Code P0471?

http://howtobyme.blogspot.com/2011/11/error-code-p0471-on-2007-dodge-ram-3500.html

-------------
P0304 Error code?

http://howtobyme.blogspot.com/2011/11/p0304-error-code-on-dodge-neon.html

-----------------


OBDII scan is receiving NO BUS CODE?

http://howtobyme.blogspot.com/2011/11/obdii-scan-is-receiving-no-bus-code.html

-----------
How to Clear OBD error Codes?

http://repairhelpcenter.blogspot.com/2011/11/how-to-clear-obd-error-codes-on-acura.html

----------------
Diagnosis and Testing Car Components?

http://vwrepairhelp.blogspot.com/2011/11/diagnosis-and-testing-car-components.html

--------------
Diagnostic Trouble Codes list?

Part 1.

http://repairhelpcenter.blogspot.com/2011/11/diagnostic-trouble-codes-list-for-acura_18.html

--------------
Diagnostic Trouble Codes list?

Part 2.------

http://repairhelpcenter.blogspot.com/2011/11/diagnostic-trouble-codes-list-for-acura.html

------------
OBD Code is cleared but check engine light will not RESET?

http://schematicsdiagram.blogspot.in/2012/02/obd-code-is-cleared-but-check-engine.html

--------------
Diagnostic Code 43 and 71?

http://schematicsdiagram.blogspot.com/2011/12/diagnostic-code-43-and-71-on-1991.html

------------------
Code P0132?

http://schematicsdiagram.blogspot.com/2011/12/code-p0132-on-acura-tl.html

-------------
P0031 code?

http://schematicsdiagram.blogspot.com/2011/12/p0031-code-on-dodge-dakota.html

--------------
How to get diagnostic Code without OBD Scanner on Pre 1995 cars?

http://schematicsdiagram.blogspot.com/2011/12/how-to-get-diagnostic-code-without-obd.html

------------
OBD-II Trouble Code P0300?

http://schematicsdiagram.blogspot.com/2011/12/obd-ii-trouble-code-p0300.html

-------------
Getting diagnostic code P0016?

http://schematicsdiagram.blogspot.com/2011/12/getting-diagnostic-code-p0016.html

--------------
How to Read Codes from Check Engine Light?

http://schematicsdiagram.blogspot.com/2011/12/how-to-read-codes-from-check-engine.html

-------------
Diagnostic Code P0540 continues to return and the MIL light is on?

http://schematicsdiagram.blogspot.com/2011/12/diagnostic-code-p0540-continue-to.html

-----------
DTC Trouble Code P0401?

http://schematicsdiagram.blogspot.com/2012/01/dtc-trouble-code-p0401.html

-----------------
Car misfires and error code P0306 and P0303 is shown?

http://technoanswers.blogspot.com/2012/01/car-misfires-and-error-code-p0306-and.html

-------------
Diagnostic code P0463?

http://technoanswers.blogspot.com/2012/01/diagnostic-code-p0463-on-ford-f250.html

-------------
Check engine light with codes P2195 and P2197?

http://howtobyme.blogspot.in/2012/01/check-engine-light-with-codes-p2195-and.html

------------
Diagnostic error code P0121,P0505,P1000,P2101,P2104, P2110,P2135,P2106?

http://technoanswers.blogspot.in/2012/01/diagnostic-error-code.html

--------------
P0174, P0037 and P2197?

http://technoanswers.blogspot.in/2012/02/p0174-p0037-and-p2197-on-toyota-rav4.html

-----------
P0352 Obd code?

http://technoanswers.blogspot.in/2012/02/p0352-obd-code-on-toyota-rav4.html

-------------
Error code p0402?

http://technoanswers.blogspot.in/2012/02/error-code-p0402-on-ford-escape.html

---------
Obd Code P0763?

http://technoanswers.blogspot.in/2012/02/obd-code-p0763-on-lexus.html

-------
OBD code P0301, P0430 and P0174?

http://schematicsdiagram.blogspot.in/2012/02/obd-code-p0301p0430-and-p0174.html

---------
OBD code P0500?

http://schematicsdiagram.blogspot.in/2012/02/obd-code-p0500-on-lexus-rx-300.html

-----------

This will help.

Thanks.


------------------------------------

Feb 09, 2012 | 2003 Lincoln Town Car

3 Answers

Can't get my 96 chev s-10 to pass inspection due to Not ready codes. I recently change the battery and have driven the veh about 200 miles. Autozone checked and said it was all good but the state...


Here is the drive cycle procedure for that vehicle, and let me know if you require any further assistance.


Running an OBD-II Drive Cycle

The purpose of the OBD-II drive cycle is to run all of the onboard diagnostics. The drive cycle should be perfomed when any trouble codes are erased from the PCM or if the battery was dis-connected. Performing the drive cycle will reset the monitors so that any further trouble codes can be detected.

The OBD-II system drive cycle begins with a cold start with the coolant temperature below 120 degrees F. and the coolant and the air temperature sensors within 10 degrees of each other. (The ignition key must not be "on" or in the "Run" position until the cold start or the heated O2 sensor diagnostic might not start)

1. As soon as the vehicle starts up, idle the engine in drive for two and a half minutes with the AC and the rear defrost on if equipped with a rear window defroster. The OBD-II will check the O2 sensor circuits, the air pump, and the EVAP purge.

2. After the two and a half minutes turn off the AC and the rear window defrost, and then accelerate to 55 mph at half throttle. OBD-II checks for any ignition mis-fires, fuel trim, and canister purge.

3. Hold steady at 55 mph for three minutes. OBD-II monitors the EGR system, the air pump, the O2 sensors and the canister purge.

4. After the three minutes decelerate down to 20 mph without using the brakes or the clutch. OBD-II checks the EGR and the purge functions.

5. Accelerate back up to 55 mph at half throttle. OBD-II checks for mis-fires, fuel trim, and purge functions again.

6. Hold steady at 55 mph for five minutes. OBD-II will monitor catalytic converter efficiency, for any mis-fires, EGR function, fuel trim, O2 sensor operation, and purge functions.

7. Decelerate to a stiop without using the brakes or the clutch. OBD-II makes a final check of the EGR system and the canister purge functions.

Sep 12, 2010 | 1996 Chevrolet S-10 Pickup

2 Answers

How to change a throttle position sensor on a 94 ford f150 5.0 4x4


How to Replace a Throttle Position Sensor
(DIY & Save up to $135.75 ) - Time: 2.1 hours

Parts:
1. Throttle Position Sensor - $ 55.44

Tools:
1. Scan Tool
2. Screwdriver
3. Multimeter

Procedure:
1. Locate the OBD data link connector (DLC). Refer to your owner’s manual for the specific location.
  • Tip: The OBD-I data link connector is usually located in the engine compartment near the battery or the fuse box. The OBD-II connector (post 1995 cars) is usually located beneath the instument panel next to the steering column.
2. Turn your key to the“ON” position. Do not start the engine.

3. Plug your scan tool into the OBD data link connector. Turn on the scan tool and select the appropriate steps to read the diagnostic trouble code (DTC).

    6db8845.jpg

Scanner plugged into OBD-II data link connector.
  • Tip: The OBD-II diagnostic trouble code (DTC) is a 5 character alphanumeric code. The first digit is a letter that indicates the component group, the second digit is OBD mandated or manufacturer specfic, the third digit is a subgroup, and the fourth and fifth digits define the component and basic problem.
  • 4. Locate the throttle position sensor.
6182d26.jpg

  • Throttle position sensor

  • 5. Disconnect the electrical connector from the throttle position sensor.
fc565b1.jpg

  • Electrical connector removed
6. Test the resistance of the throttle position sensor (TPS) with a digital multi-meter. If the resistance is out of specifications, the TPS must be replaced.
  • 7. Remove the throttle position sensor.

  • d3a8007.jpg

    Removing sensor mounting screws

    8. Install the new throttle position sensor. Tighten the mounting screws and attach the electrical connector.
  • 9. Erase the diagnostic trouble code (DTC) with the scan tool using the“delete” or“erase” command. Road test your vehicle to see if the check engine light returns.
fde01cf.jpg

    Check engine light

  • Tip: If the check engine light returns, repeat the diagnostic process for additional DTCs or take your vehicle to a certified repair shop.
Direct OE replacement

Hope helped with this. Good luck (remember rated this help).

Nov 05, 2009 | Ford F-150 Cars & Trucks

1 Answer

Where can i get a copy of the parts that make up the air suspesion of my 2001 grand marquis. sometime it works and other time it will not.


Vehicle Dynamic Suspension The vehicle dynamic suspension consists of the following components:
  • Rear air suspension control (RAS) module (5A919)
  • Snorkel
  • Drier
  • Air compressor (5319)
  • Air suspension switch (5K761)
  • Solenoid valve (5311)
  • Air spring (5560)
  • Air suspension height sensor (5359)
  • Air line
------------------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Restricted suspension movement
  • Excessive vehicle load
  • Cut, severed, or crimped air line(s)
  • Damaged air spring(s)
  • Height sensor damage
  • Height sensor mounted incorrectly, disconnected, or damaged
  • Central junction box (CJB):
    • Fuse 5 (15A)
  • Battery junction box (BJB):
    • Fuse 8 (30A)
  • Loose or corroded connectors
  • Air suspension switch OFF


The air suspension control module is diagnosed using Super Star II Tester 418-F045 (007-0041B) or equivalent.
The test connector used to communicate with the air suspension control module is located on the RH side of the luggage compartment.
When the tester is connected, the engine is started and the HOLD/TEST button is latched down, the air suspension control module will respond sending a code 10 to the Super Star II Tester which represents "Diagnostics mode entered." If diagnostic trouble code (DTC) 10 is not displayed, go to Pinpoint Test A.
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index
Condition Possible Sources Action
  • No communication with the air suspension control module
  • CJB Fuse 5 (15A).
  • BJB Fuse 8 (30A).
  • Circuitry.
  • Air suspension control module.
  • GO to Pinpoint Test A .
  • Unable to enter auto test
  • Air suspension control module.
  • Circuitry.
  • GO to Pinpoint Test B .
  • Rear air suspension does not respond to load changes
  • Circuitry.
  • Air compressor.
  • Air compressor inlet tube.
  • Air compressor drier.
  • Air suspension height sensor.
  • Air suspension control module.
  • GO to Pinpoint Test C .
  • Rear rides low/high
  • Circuitry.
  • Air spring solenoid.
  • Air suspension height sensor.
  • Air suspension control module.
  • GO to Pinpoint Test C .
  • Poor ride quality
  • Circuitry.
  • Air springs.
  • GO to Pinpoint Test C .
  • Air suspension warning indicator ON
  • Air suspension switch OFF.
  • Place the air suspension switch in the ON position.
  • Air suspension control module.
  • Circuitry.
  • GO to Auto Test.
  • Instrument cluster (conventional cluster) or lamp warning module (electronic cluster).
  • REFER to Section 413-01A (conventional cluster) or REFER to Section 413-01B (electronic cluster), or REFER to Section 413-01C (natural gas cluster).


Sep 25, 2009 | 2001 Mercury Grand Marquis

2 Answers

Air suspension is dead on the ground fuse is good will not raise?


Check the suspension switch on the trunk, I think is on the driver side, something should happen if you turn it on/off.

Sep 17, 2009 | 1994 Lincoln Town Car

1 Answer

2002 linncoln towncar where is the air supension compressor relay switch,please.


Air suspension needs compressed air for the control of Air Springs (Air Spring is a cylinder like thing which goes up and down when air is pumped in and out of it). For pumping in and out the air, air compressor needs to be switched ON/OFF. Compressor relay connects and disconnects the compressor motor from the power supply ( battery). ----------------- air ride suspension compressor located under the air filter box . ---------------- the Air compressor clutch relay location
is fitted to the left hand inner wing (when viewed from the the driving seat).
-------------------
the compresser is located on the left hand side of the car under the hood.
once you open the hood remove the air cleaner housing and windshield washer resivor.
there is a panel that you lift up under both of thoese that is where the compresser is located
-------------
  1. The air suspension uses a small, separate air compressor under the driver's side left fenderwell, with air lines running to the air bags. On the top of each air bag is a electrical valve. This is a relief valve that allows air to be exhausted when activated, and which senses the amount of air pressure within the air bag to keep both sides equal. These valves are operated via a leveling sensor that is attached to the body of the car and to the rear axle by a movable arm. When the rear of the car drops due to increased load, the arm is pushed up. When the arm is pushed up, it turns on the air compressor and fills the air bags to level the car. When the load is removed and the arm moves down, indicating that the back of the car has risen, the sensor opens the valve on the air bags and allows air to escape, lowering the car.
  2. If the back of the car is low, indicating that the air suspension is not working, and the air suspension light is on, check the fuse first. If the fuse is all right, check the air suspension switch in the trunk and make sure it is on. This switch is used when the car is in for service. Always turn off the switch before lifting the car, because the sensor will think the car is rising and keep the air bag valves open, ruining the rear air suspension.
  3. Turn the ignition key with the engine off. Listen for the compressor to come on while pushing down on the rear bumper. If it does not come on, test the switch terminals for power, using a circuit tester. If one terminal has power and the other does not, replace the switch. If there is power, turn the switch to the off position, raise the vehicle and place it on jack stands in the rear. Inspect the leveling switch on the axle, making sure it is not bent and is connected. Use an ohmmeter for this test. Pull the electrical connector off the switch. Loosen the arm of the switch from the axle. Test the switch with the ohmmeter by checking across both terminals while slowly moving the arm. There should be no continuity with the arm down. As the arm is raised, there should be continuity. If not, replace the switch. If there was continuity, connect the arm and the electrical connector.
  4. Put a floor jack under the axle and raise the axle to the point where it is just beginning to lift the car off the jack stand. Turn on the ignition. Turn the air suspension switch to the "on" position. Use the circuit tester to check for power at the leveling switch. If there is power, turn the air suspension switch to "off" and lower the car. Access the air compressor in the front, under the hood, and check the electrical connector for power. If there is power, check for a good ground. If both are good, replace the compressor. If the compressor works and the car does not rise in the back, replace the air bags.


Sep 11, 2009 | 2002 Lincoln Town Car

Not finding what you are looking for?
2002 Oldsmobile Silhouette Logo

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...