Question about 1998 Buick Regal

1 Answer

Have an intake manifold problem been reported?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

All gm vehicles are known for leaking intake manifold gaskets. They are made of plastic and they crack and break from age.

Posted on Nov 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a map sensor


Lets see, it will have a 3 wire electrical plug, disconnect that, then it will have a vacuum hose or a fitting direct to the intake manifold (because it simply reads the intake manifold air pressure and reports it to the engine computer), so you remove the vacuum fitting, then the sensor case may be retained or attached by screws-remove them and replace with the new one. So there you are, and that's all I have to say about that.

Feb 21, 2016 | Cars & Trucks

1 Answer

Fault codes daewoopo108


P0108 Manifold Absolute Pressure (MAP) Circuit High Voltage points to a manifold absolute pressure (MAP) sensor that's reporting a continuous low intake manifold vacuum pressure condition regardless of present engine operating conditions. Most likely a bad MAP sensor

Aug 22, 2014 | 2001 Daewoo Tacuma 1.8

3 Answers

I need an intake manifold for a 2001 Grand Cherokee 4.7L V8


Get rid of the vehicle they are not worth the effort to get fixed and the cost of genuine parts in Australia is crazy,Jeeps are so unreliable and defineatly not suited to travel any further the 20klms outside of GPO of your capital city..As for a 4 wheel drive they are only suited to the K.Mart carpark..Have only 2 Jeeps before and only had good reports and minor maintainance work

Jul 03, 2014 | 2001 Jeep Grand Cherokee

1 Answer

97 gmc acted like had bad gas but now also at idle with brake on engine will surge and engine sounds like it s missing


Hi Allen, The brake booster is connected to the intake manifold and that is where the low pressure is generated. If the diaphragm or one way valve, or connection pipe is leaking it will give the same effect as a leakage on the intake manifold. The symptoms you report are of a leakage on the intake manifold. To prove one way or another, disconnect the vacuum pipe for the booster and block the connection into the intake manifold. Be careful when testing as you will need to use excessive force on the brake pedal to stop. If the symptoms disappear fit a new booster, if not, pour water along the manifold and observe any bubbles where there may be a leakage. Let me know how you get on. Regards John

Aug 10, 2012 | GMC Sierra Cars & Trucks

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

2000 lexus rx300 has check engin light with codes of 1130 and 1150. what is the problem?


Both codes indicated a failure in the outputs of your air fuel ratio sensors. Because of the fact that both sensors are reporting incorrectly, I would suggest checking your AF relay underhood for failure, or your ground wire on the back of the intake manifold for connection.

Often when these cars have spark plugs changed or valve cover gaskets changed, the ground wire on the back of the intake (which must be removed to perform the mentioned jobs) gets left dangling. With this ground wire not attached, both A/F sensors will report 0voltage, resulting in the two codes you received.

Oct 17, 2009 | 2000 Lexus RX 300

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

1 Answer

What Happens When a Map Sensor Goes Bad on 2001 dodge durango?


Manifold Absolute Pressure sensor controls fuel delivery and ignition timing, the pressure in the intake manifold will vary due to stress or work load, the MAP sensor monitors this, reporting to the computer. Good luck.

Jul 12, 2009 | 2001 Dodge Durango

Not finding what you are looking for?
1998 Buick Regal Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...