Question about 2004 Chevrolet Malibu Maxx

Open Question

How do you remove and replace the alternator on a 2004 malibu 6 cylinder?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76132 Answers

SOURCE: how do you replace the starter in 1998 chevy malibu

The starter is very simple to replace, 1st always disconnect the battery, the wires at the starter are hot with 12 volts always present, remove the 2 attaching bolts for the starter to the engine block, then remove the wiring, one heavy cable and a bunch of smaller wires, one of those goes to the starter solenoid, mark it, the others are what are called fuse links and provide power to the rest of the car, clean up everything and then re-install in reverse order.

Posted on Dec 01, 2008

Ad
  • 181 Answers

SOURCE: i have a 1998 malibu ls 6 cylinder and the cam

Yes you will need to remove the pump first to gain access to the bolt holding it in and be able to pull the sensor out of the hole.

Posted on May 19, 2010

  • 236 Answers

SOURCE: I have to travel to replace the alternator on a

This is the 2.2l engine
0900c1528024bace.jpg Below are the v6 mounting
0900c1528024bacf.jpg I recomend a set of metric sockets a 3/8 inch drive ratchet and a cheater pipe to fit over the ratchet to release the pressure off the belt. Should not be to difficult. The bolts are probably 14 or 13mm. GoodLuck. If this is helpful ,Please leave positive feedback. Thanks, SnugglePants

Posted on Oct 21, 2009

  • 3640 Answers

SOURCE: is it hard to replace the head gaskets on a 2004

no its not really to hard if you have some mechanical ability!! go to any autoparts store and buy a haynes manual for your car only about 20.00, the books are based on a complete teardown of vehicle.

Posted on Nov 03, 2009

reisdos
  • 1297 Answers

SOURCE: Fan belt broke on my son's 2000 Chev Malibu -

yes... easy

you should have one belt called a serpentine

here is the 3.1 routing
e88cb98.gif

here's the 3.8 routing
fade3e8.gif

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cylinder 3 location on a 2004 gmc envoy


The coil pack will be numbered. Find coil #3 and follow the spark plug wire to the spark plug.

Jun 15, 2014 | 2003 GMC Envoy

1 Answer

IM TRYING TO REPLACE THE THERMOSTAT ON MY 2004 ENVOY WHERE IS IT LOCATAED EXACTLY


The thermostat on this vehicle's In-line 6 cylinder engine is on the driver's side of the engine, below & behind the alternator. You have to remove the alternator to gain access to the thermostat housing. You also need to disconnect the battery before you remove the alternator to avoid sparks and shorts.

Most directions outline removal of the alternator to gain easy access to the hose clamps, bolts and housing of the thermostat. I have located a site that after free registration, has detailed instructions on how to do this job, and the link below that describes an easier method with photos. Check out:

http://forums.trailvoy.com/showthread.php?t=54225&highlight=replace+thermostat

Mar 15, 2011 | 2004 GMC Envoy

1 Answer

Engine code: Misfire cylinder 1. Replaced plugs


There should be no built up fuel or oil in cylinder. The fuel will be burned off immediately, and there should have been very little unless you have a leaking injector. The only way oil will enter the cylinder is if you have a mechanical failure like worn rings or leaking valve seals.If after replacing the plugs and wires did not correct all or the skip after the first start up and road test then you have another issue causing the skip

May 23, 2010 | 2004 Chevrolet Malibu

1 Answer

What size engine does a 2004 chevy malibu have?


2004 Chevrolet Malibu
4 Cylinders F 2.2L SFI DOHC
6 Cylinders 8 3.5L SFI

2004 Chevrolet Malibu Classic
4 Cylinders F 2.2L SFI DOHC

Good luck (remember comment and rated this).

Apr 16, 2010 | 2004 Chevrolet Malibu

1 Answer

Firing order diagram for 1998 3.1


the firing order is, 1-2-3-4-5-6. coils from left to right are: 5-2-3-6-4-1. number 1 cylinder is in back under alternator or next to it.

Mar 30, 2010 | 1998 Chevrolet Malibu

2 Answers

I have to travel to replace the alternator on a 2004 malibu classic 4 cylinder and would like to know what tools are required to do so


This is the 2.2l engine
0900c1528024bace.jpg Below are the v6 mounting
0900c1528024bacf.jpg I recomend a set of metric sockets a 3/8 inch drive ratchet and a cheater pipe to fit over the ratchet to release the pressure off the belt. Should not be to difficult. The bolts are probably 14 or 13mm. GoodLuck. If this is helpful ,Please leave positive feedback. Thanks, SnugglePants

Oct 21, 2009 | 2004 Chevrolet Malibu

2 Answers

Replace thermostat on 2004 gmc envoy


The thermostat on this vehicle's (the Envoy & Trailblazer are essentially the same vehicle) In-line 6 cylinder engine is on the driver's side of the engine, below & behind the alternator. It is not found in the typical location (which may be for the 8 cylinder engine), in an answer above.

Most directions outline removal of the alternator to gain easy access to the hose clamps, bolts and housing of the thermostat. I have located a site that after free registration, has detailed instructions on how to do this job, and the link below that describes an easier method with photos. Check out:

http://forums.trailvoy.com/showthread.php?t=54225&highlight=replace+thermostat

Jul 17, 2009 | 2004 GMC Envoy

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

837 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...