Question about 2002 Ford F250 Super Duty SuperCab

1 Answer

I have just changed my oil and after adding 6 qts. back it is still showing low on the dip stick should I just leave it alone or add to the full line

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

What size engine?

Posted on Nov 07, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Oil dipstick tube broke

look on dip stick you should see cross hatched area with add oil or oil full mark.if you wipe oil dip stick with a clean paper towel and dip stick look dry no sign of oil add little oil at a time see if oil level reach add oil mark or the full mark.if oil is low. low oil light will turn on if bulb is blowed but if dip stick look dry oil level could be low,add little bit at a time dont over fill.

Feb 16, 2012 | Cars & Trucks

2 Answers

I bought a 1998 Chrysler Sebring LXi recently and it didn't come with an owners manual... How many quarts of oil does the engine need?

Buy 5 qts of oil. Drain the oil and replace the filter. Add 4 qts and start the engine. let it idle for a few minutes. Shut it off and recheck the level on the dipstick, use the last qt to finish adding to full if necessary.

Sep 18, 2011 | Chrysler Sebring Cars & Trucks

3 Answers

How much quarts does a 99 hyundai accent take?

Hi, your 1999 Hyundai Accent will need about 3.5 - 4 quarts of 5w30 Motor oil.

Jul 24, 2011 | 1999 Hyundai Accent

2 Answers

How many quarts of oil does it take for a suzuki grand vitara 2002 6 cylinder 24 valve 2.4 liter

put in 3.5 quarts of oil and before you start the car check the oil level on the dip should be about half a quart above the full line on the dip stick(upper line) i assume you are changing your own oil and filter.start car let it run a little while shut car off let it stand and recheck oil should be at the full mark.if low put in rest of the last quart of oil.recheck.most cars hold 4 quarts.

Apr 20, 2011 | 2002 Suzuki Grand Vitara

1 Answer

Bought the envoy w/ 70,000 miles, fresh oil change. @ 74,000 miles it was 1.5 qrts low, put in 5w30, checked oil 2 weeks later it was 1 qrt low. do not see smoke or any leaking.

I just bought a 2005 envoy too. I read in the manual that the 4.6 6 cyl engine needs 7 qts total. 2 Over the normal oil change. Is it possible it wasn't low to start? I noticed when Walmart changed the oil they charged extra for the change because it needed the two extra qts. However my dip stick has oil over the full mark. Seemed strange but I haven't had any leaks and after 3k mile no change in level. Make sure you had the correct about the first time.

Dec 29, 2010 | 2005 GMC Envoy

2 Answers

When do I add Oil?

Really you should not have to add oil. But to find out have jeep on level surface and use the dip stick to check. Check with car off, pull dip stick out and wipe off and reinsert, Pull back out and read the stick only add if it is low. Do not over fill.

Sep 23, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

Have a 2000 mazda millenia S . How much oil does it need?

normal with oil filter is 4.3 qts. do not trust the dipstick, it is a very crude measuring device. the best way to find out exactly where on the dipstick to look, is to completely drain your oil, and change the filter. do this when the engine is warm, and let it drain for a while. then, add fresh oil and filter, exactly 4.3 qts, and start it for a minute(to get the oil thru the filter). let it sit for at least 30 minutes to allow all the oil to get back into the sump. THEN see where it is on the dipstick. on both our cars, the dipstick shows almost a qt low, even tho 4.3 qts has been added.

Jun 09, 2009 | 2000 Mazda Millenia

2 Answers

Quantity of Oil to use

most only take 5 qt put in 4 and check the dip stick if it is on full run the engine for a min and let it stand for a bit recheck and add what you need to full mark

Apr 05, 2009 | 1998 Mercury Sable

1 Answer

I want to know how much Engine Oil is required.

I would say between 5-6 quarts.
I would add at least 4 qts. Then check the oil dip stick. Then add the rest of the oil accordingly till full.

Apr 04, 2009 | 2003 Mercedes-Benz E-Class

1 Answer

2001 malibu transmission slipping

lvd, Start the car, leave the shifter in park position.
Remove the transmission dip stick, wipe it clean, reinsert the dip stick and verify it is between the add and full mark.
Do not go over the full mark as that will create a slip condition caused by foaming oil.
Let me know.

Feb 26, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
2002 Ford F250 Super Duty SuperCab Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides