Question about 2000 Mitsubishi Montero Sport

1 Answer

Fog lamp brackets

I need A diagram on how to install fog lamps and brackets on A 2000 montero sport. Thank You Jimmie

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Names & locations of the relays in the auxiliary relay box 1 on a 2003 ford explorer sport trac


There are two relay's for the fog lamps in that relay box . fog lamp isolation an fog lamp relay . You can find a diagram here http://www.bbbind.com/free_tsb.html Enter your vehicle info. year , make , model , engine size . Under system click on electrical distribution , then under sub system click on relay . Hit the search button , then click on the link . Good luck !

Mar 21, 2017 | 2003 Ford Explorer Sport Trac

1 Answer

How do I replace the fog light? what needs to be removed to access fog lights and side marker lights.?


SECTION 417-01: Exterior Lighting 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/27/1999 Fog Lamp Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Remove the aeroshield-to-sub frame screws.
    a0008736.gif
  1. Remove the seven screws and remove the aeroshield.
    a0009383.gif
  1. Disconnect the fog lamp assembly electrical connector.
    a0011782.gif
  1. Remove the fog lamp assembly.
    1. Remove the screws.
    1. Remove the lamp assembly.
    a0011783.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n161420&c35=wsm%2cfog%20lamp%2csyh%2c417-01%2cremoval%20and%20installation&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 05, 2011 | 2000 Mercury Sable

1 Answer

The fog lights stay on after the ignition is turned off killing the battery


Your fog lamp relay is stuck open you need to locate it and replace it.Usually located under the hood in engine compartment in the fuse relay cluster.Open the cover and on the diagram detailed and numbered you will see fog lamp relay remove and replace this relay is most likely a dealer item.

Dec 28, 2010 | 2000 Mercedes-Benz SLK

1 Answer

NEED TO REMOVE EXISTING FOG LAMP HOUSING FOR REPLACEMENT


Hi, the fog lamp is held on , by 2 bolts at the back side of the bumper, on top of the fog lamp bracket. You would have to go underneath the bumper, and remove the two bolts, with a 10mm wrench. They are a bit tricky to get to, but it is easily done. Good luck...Coop

Sep 26, 2010 | 2002 GMC Yukon XL

1 Answer

How to take off existing fog lights on a 2003 escalade and install new fog light assembly


The fog lamp assemblies can be removed by getting underneath the front bumper and on top of the fog lamp assemblies you will find the metal mounting bracket. The bracket attaches to the vehicle with 3 small bolts that are 8-10mm (i forgot exactly) that bolt down through the bracket into the front bumper cover above the actual lens itself and can be accessed with a box wrench. I replaced both assemblies in mine in under 1/2 and hour!

Jun 24, 2010 | Cars & Trucks

1 Answer

How to factory wire fog lights on a 2000 ford f150. pig tail, relay, and fuse are there. Only no wiring from fuse box.


This is a common problem on 97-00 MY trucks, regardless of the trim level ( XL, XLT, Lariat ).

If you install the fog lamp fuse in the BJB ( aka Battery Junction Box, Engine Compartment fuse panel ) Fuse # 9 ( 15 A fuse ) and jumper the normally open contacts in the fog lamp relay socket ( see diagram below ) the fog lamps should illuminate ( to confirm what you have doing on ).
8491ddd.jpg
The problem usually is the main headlamp switch to the BJB is not in place ( this is the yellow wire from the main headlamp switch connector to the relay socket pin #1 ).
One easy route is to make an aux lighting relay & harness, or purchase one online. With this, you can cut the factory ends and attach them to the harness you purchased. There is an air inlet next to where the steering wheel column runs through the firewall. This would give you an easy route to the fog lamp switch. The fog lamp switch, you can buy the factory one, and change the yellow wire from the connector to your added relay, or just add a switch for this function.
This will give you an idea of what the DIY relay and harness would look like.
5954a15.jpg

Hope this helps, more than confuses at this point

Sep 16, 2009 | 2000 Ford F150 Flareside SuperCab

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

How to replace a fog lamp with replacement bulb only on 2002 toyota 4runner sport edition???? the three screws on the bottom?


Well, these are the steps and I will post the pic here in a second...looks like 2 screws...but like I said, you can see the picture for direction on this.


Remove or disconnect the following:

Front turn signal lamp
  • Connector
  • 2 screws
  • 2 claw fittings
  • Fog lamp assembly
  • Fog lamp bulb as shown
  • Fog light unit

  • To Install
    1. Install or connect the following:
      • Fog light unit
      • Fog lamp bulb as shown
      • Fog lamp assembly latch the 2 claw fittings and 2 screws
      • Connector
      • Front turn signal lamp
    Trying to post the pics now....

    May 14, 2009 | 2002 Toyota 4Runner

    2 Answers

    I need a wiring diagram for fog lights oem to my toyota


    The link below is a Typical fog lamp / driving lamp hookup. Keep in mind that in most states, for these lamps to be 'legal' (and thus pass inspection), you must wire them such that:

    1. You can cut them off (in other words, there must be a switch installed to turn them off)

    and

    2. They may only be operated with the low beams. (therefore, you must power your on/off switch from the low beam circuit)

    http://www.accessconnect.com/fog_driving_lights_wiring.htm

    Feb 28, 2009 | 2005 Toyota Corolla

    1 Answer

    HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


    ATTN: NIKKICARROLL

    here is how to replace the bulb in your vehicle


    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
    3. Remove the screws holding the headlamp module halves together.
    4. Separate the module halves.
    5. Disengage the wiring from the headlamp bulb.
    6. Remove the retaining ring from the back of the headlamp bulb.
    7. Pull the bulb from the lamp.
    To install:
    1. Push the bulb into the lamp.
    2. Install the retaining ring to hold the bulb in the lamp.
    3. Engage the wire connector to the back of the headlamp bulb.
    4. Place the module into position on the vehicle.
    5. Install the screws to hold the module to the vehicle.
    6. Install the radiator closure panel sight shield.
    7. Check the headlamp alignment and operation.
    88176gb1.gif Exploded view of the fog lamp with the bulb removed
    Click to Enlarge

    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
    3. Remove the screws holding the headlamp module halves together.
    4. Separate the halves.
    5. Remove the fog lamp wire connector cover.
    6. Disconnect the wires from the fog lamp bulb.
    7. Disengage the retainer clip holding the bulb to the fog lamp.
    8. Remove the bulb from the fog lamp.
    To install:
    1. Place the bulb into position in the fog lamp.
    2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
    3. Attach the wire connectors to the fog lamp bulb.
    4. Install the fog lamp wires connector cover.
    5. Place the module halves together.
    6. Install the screws to hold the headlamp module halves together.
    7. Install the radiator closure panel sight shield.
    8. Verify the fog lamp operation and alignment

    ATTN: WDSNEED1

    Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
    Click to Enlarge

    1. Release the hood latch and open the hood.
    2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
    3. Remove the screws holding the headlamp module to the mount adapter.
    4. Separate the headlamp module from the mount adapter.
    5. Disengage the wiring from the headlamp and foglamp.
    6. Remove the headlamp from the vehicle.
    To install:
    1. Attach the wires to the headlamp and foglamp assembly.
    2. Place the headlamp module into position on the mount adapter.
    3. Install the screws to hold the headlamp module to the mount adapter.
    4. Install the radiator closure panel sight shield.
    5. Check the headlamp alignment and operation.

    Jul 28, 2008 | 1994 Chrysler New Yorker

    Not finding what you are looking for?
    2000 Mitsubishi Montero Sport Logo

    Related Topics:

    210 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    70387 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6878 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...