Question about 1998 Ford Taurus

1 Answer

I need the tourqe setting for the connection from the tie rod end to the rack & pinion.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 228 Answers

Tie rod end torque settings. tie rod end and castllated nuts 35-46 ft lbs.

tie rod end jamb nut. 35-46 ft lbs.

rack and pinion. power rack and pinion subframe retaining bolts. 85-99 ft lbs.

good luck!

Posted on Feb 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rack & pinion steering replacement


DISCONNECT TIE RODS ENDS FROM WHEEL HUB, DISCONNECT POWER STEERING HOSE FROM RACK AND PINION, DISCONNECT RACK AND PINION FRON LOWER ENGINE COMPARTMENT

Feb 19, 2014 | 2003 Chevrolet TrailBlazer

1 Answer

Change power steering pump


Play in the steering wheel is likely from worn tie rod ends. Have your inner and outer tie rods checked. The outer tie rods are connected to the rod ends coming out of the rack on each side, and are connected to the wheels. The inner tie rods are not visible-but are on the rods under the protective boots on each end of the rack and pinion assembly.
You may need a new rack assembly, but first check if you just need new tie rods.

Nov 25, 2013 | 1997 Honda Accord

1 Answer

Rack and pinion? have play in wheel no sign of leaks new power steering pump installed


Hi Gunny, If your vehicle is fitted with rack and pinion steering also check the rack ends for play. The rack ends are the rods which the tie rod ends screw onto. The other end fits onto the rack of the rack and pinion. To work on those you will need to remove the rubber boots and loosen the locking washer, they can then be loosened with a wrench. If they are worn the play will be evident in the steering. When replacing them also replace the rubber boots. If the boots are worn and road grime and dust enters, you will see leakage from the rack and pinion in the near future. I always thought the Dakota was fitted with a steering box? Regards John

Jun 24, 2012 | 1990 Dodge Dakota

1 Answer

The left side tie rod seems to have slop on the rack & pinion side. Tie rod outter end is good.what is it?


Worn inner tie rod joint,on the steering rack

If you go to an alignment only shop, not some
chain store, with an alignment rack,they will
change it for you, if it can be done

Then you have to set all the front end adjustments

Don't let them pitch you, a complete rack assy
Moog-- makes those inner tie rods, and you put your
good outer joint on it

Dec 02, 2010 | 2005 Mercury Mountaineer

3 Answers

Is an inner tie rod, part of the rack and pinion steering?


the inner tie rod is the joint right at the end of the rack,inside the gaiter/boot,the outer is called the track rod end.

Aug 26, 2010 | 2006 Pontiac Torrent

1 Answer

I just bought a 93 honda civic and I took it to goodyear and they said I needed my tie rods tightend is there a way I can do it myself?


Yes. If it's to correct alignment, the inner tie rod shaft has to be moved into your outer tie rod and then tightened. this is all done from the wheel area.

If it is to correct play in the steering, then this should apply.

The inner tie rod connection to the Rack unit is hidden by the rack boot which will need to be removed from the Rack unit but not completely removed from the shaft, just pushed over out of the way while working on the inner tie rod adjustment. The large nut on the end of the inner tie rod will have to be loosened & checked, for any damage, then reinstalled & tightened to the correct amount necessary to cause sufficient drag on the inner tie rod but not too much to restrict it during normal use.

You may even want to consider a remanufactured Rack unit if you have too much slack in the steering. Tightening the Inner Tie Rods doesn't replace the seals & rebuild the remainder of the Rack & Pinion, yet these parts all have the same amount of wear on them that the Inner Tie Rod does.

Manuals available w/step by step instructions for your vehicle at parts stores. good luck

Feb 15, 2010 | 1993 Honda Civic 4 Door

1 Answer

Repair inner tie rod end of 1997 dodge avenger


f734654.gif #3 is the inner tie rod and it is simply screwed into each end of the steering rack. Raise and support the car remove the wheel and you should see where it is connected to the outer tie rod. There is a lock nut that you'll need to loosen slightly to get the tie rod off. You will need to get a wheel alignment once done but by slightly loosening the lock nut, you have a good reference of how it should be once done. Once loose, you should be able to turn the tie rod by using a wrench on the flattened area on the rod. Once disconnected from the outer tie rod end, you should be able to remove the dust boot covering the inner tie rod connection. Mine came right apart so hope you have no problems. After you have it out, here is where the loosened locknut comes into play. Put the new and old tie rod side by side, line up the ends that attach to the rack and pinion then mark the new rod so you know how far to put the lock nut on the new tie rod. Simply tightly screw the new one onto the rack and pinion put the boot back, screw on the lock nut to the mark then attach the tie rod to the outer tie rod end up to the lock nut then tighten the lock nut against the outer end. Get the tire back on, lower the car and Voila, done. Now go get an alignment.

Nov 18, 2009 | 1997 Dodge Avenger

2 Answers

How to change inner tie rod ends?


if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------
  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Apr 15, 2009 | 1997 Ford Windstar

1 Answer

Rack pinions and bushing installement


pretty decent job ahead first jack up car support with jack stands remove front wheels remove nuts on tie rod ends remove tie rod ends from spindles with tie rod end tool or tap with malet were they sit to loosen them hit the spindle area not the tie rod or tie rod threads then dissconnect power steering lines from steering rack also disconect steering linkage to rack there should be 2 main bolts holding assembly to frame remove them should free rack i know that car may have a unique design were u may have to remove inner tie rod ends first if it has those round bushings that always go bad disconect inner tie rod ends behind engine on top of steering rack then remove rack from wheel well replace those inner tie rod bushings u may be able to leave outer tie rod end connected to spindles and u may be able to get to the sterring rack from behind engine good luck

Mar 28, 2009 | 1997 Chrysler Concorde

1 Answer

I need to replace the inner tie rods on my 97' conti......need a diagram of how to and any other info pertinent to the job - Bair


If this is a rack and pinion type steering, in order to remove the inner tie rods you will first have loosen the jam nut at the outer tie rod end,next unbolt the outer tie rod from the steering knuckle, unscrew the outer tie rod end off (be sure to count how many turns to remove), next remove the inner bellows boot (black boot) from the tie rod / rack and pinion, next is to unscrew the inner tie rod from the rack assembly (the do make a tool for this to make it easier) but if you do not have the tool,you can sometimes use a big pair of channel locks or a big enough wrench to fit on the fitting on the inside of the inner tie rod, and just unscrew the inner tie rod (normal left=loosen, right=tighten). Hope this helps. Would also recommend having it aligned after you are finished.

Mar 12, 2009 | 1997 Lincoln Continental

Not finding what you are looking for?
1998 Ford Taurus Logo

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...