Question about Lincoln Navigator

Open Question

How do I remove rear axle on a 1999 lincoln navigator ? I need to change seal and can't get axle out do they have a pin or something inside housing.thank you for helping

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

  • 883 Answers

SOURCE: Rear Axle Removal

rate me solved...this is all I can find...

figure 1

d164665.jpg

figure 2
c12dde8.jpg

defeae4.jpg

Posted on Jun 27, 2008

warlock61
  • 659 Answers

SOURCE: How do I close the rear side windows in a 2007 lincoln navigator?

the switch is located in the overhead console.

Posted on Dec 21, 2008

  • 4 Answers

SOURCE: Rear Axle Leak

It might be the bearings that failed and letting the axle rest on the seal. Its a common problem for these cars. I've replaced mine and it did it again so now im replacing the rear end.

Posted on Jan 19, 2009

  • 52 Answers

SOURCE: Rear Axle Seal Replacement

remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Posted on Apr 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace rear axle seal on a 1999 chevy Silverado?


Watch the You Tube Video

Remove the rear axle cover
Remove the carrier bolt & pin
Push the axles in
Remove the C-Clips
Pull the Axles
R & R the housing end seals

Sep 30, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

Rear Axle Shfat. How To?


C Clips you mean. there is a pin in the middle of the ring gear. this pin must be removed and then you push in on each axle, then the clip may fall out, or you will need to remove it from the end of the axle. then you can pull the axle out. You dont say "why" you are replacing it, replace the axle bearing and seal.

Jun 13, 2010 | 1999 Jeep Grand Cherokee

1 Answer

How do you remove an axle on the right rear of a 1999 explorer? it has a leaking wheel seal.


1. Drain diff if it has a plug.
2. Remove rear cover
3. Undo cross pin bolt and slide the cross pin out of the carrier
4. Push axle shaft in so you can remove the C clip
axle retainers
5. Slide axle out of housing.
6. Remove axle seal and then replace axle seal
7. Reverse steps

May 25, 2010 | 1999 Ford Explorer

1 Answer

Rear Wheel Seal & Bearing on 1999 GMC Safari Van


Yes you do have to pull the axle and make sure you put everything back in the same place you removed it from. The ring and pinion shouldn't have to be bothered. You will have to remove the rear end cover to remove the axle. Its very easy to do. There is a pin inside the rear end that has to be removed to pull the axle. Pay attention to how you take it out and put it back the same way. It sounds as if you can do this with no problem.

Apr 11, 2010 | 2000 GMC Safari

1 Answer

Change rear whell seal 1997 f-150 gear oil comeing out of rear whell took tire off; took drum off; and saw gear oil all over brake shoes. Seal or bearing need to be replace? how?


replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

Mar 24, 2010 | 1991 Ford F250

1 Answer

How to replace my 1994 lincoln towncar rear axel seal


you need to pull the cover off the rear diff. remove the rear brake drums or rotors, remove the bolt that holds the pin in the rear end, remove the pin, remoce the c clips, pull the axles out. remove the seal. you can do this by using one ofthe axles to pry the seal out. install the new seal and reassemble. use rtv sealant to reseal rear diff and fill with about 3 - 3 1/2 qts gear lube-may take synthetic

May 23, 2009 | 1994 Lincoln Town Car

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Need to know how to change rear wheel bearing in a 95 suburban


jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers

Jan 16, 2009 | 2003 GMC Sierra

2 Answers

Rear Axle Leak


if it is the seal, you will have to remove the caliper and rotor, remove the differential cover and remove the bolt and pin inside the diff carrier housing. push in the axle and remove the axle clip and pull out the axle use a seal puller or prybar to remove seal reverse the steps to assemble

Dec 10, 2008 | 2001 Lincoln Town Car

1 Answer

Rear Axle Removal


if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

May 29, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...