Question about 2003 Chevrolet S-10

1 Answer

How do you remove the plastic rails (attached to the drivers seat on a 60/40 bench) from center console assembly on 2003 Chevrolet S10?

Posted by on

  • 1 more comment 
  • jecanne Nov 07, 2010

    Manual...I see now how to do it now, but getting there is the problem. The two rails that come up have a plastic shell around them. I've removed that, and now see the nuts that I need to remove...The problem is, they're easy to take off on the passenger side, because you just slide the passenger seat forward and it's revealed. On the driver side, however...I have absolutely no clue. The nuts are located in a tiny hole in my seat where the seat belt buckles come out of. There is just no way I can fit a socket in that hole. So, I'm halfway there. I just can't get to those damned nuts :)

  • jecanne Nov 08, 2010

    Thanks Lee. I've managed to get the suckers off, but it wasn't easy! Mind if I hit you up for any questions in the future?

  • jecanne Nov 08, 2010

    Lee was quick to respond and clear in his instructions. Hope to see more like him! Thanks!

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,420 Answers

Welcome to FIxYa.com

manual or automatic?


Thank you for using FixYa.com

Regards, Lee Davidian

Posted on Nov 07, 2010

  • 3 more comments 
  • Auto Repair Help
    Auto Repair Help Nov 07, 2010

    can you send me a picture of this hole to leondavidiansr@gmail.com
    Thanks, Lee

  • Auto Repair Help
    Auto Repair Help Nov 08, 2010

    Thanks for the pictures very well organized. Ok yes this is a difficult bolt i would use two long wrenches. Metal hose clamp them would be cheaper then buying the extra long wrench from Snap on to get to this bolt. I have the hole set and of you were close by i would lend it to you. Thank you for the Pictures. if you need further help please reply, Regards, Lee

  • Auto Repair Help
    Auto Repair Help Nov 08, 2010

    sorry use off set box wrench

  • Auto Repair Help
    Auto Repair Help Nov 08, 2010

    do not forget to rate me thanks Lee

  • Auto Repair Help
    Auto Repair Help Nov 08, 2010

    dont mind at all

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I want to swap my 2003 Toyota avalon drivers seat with my passenger seat. How do I do this myself?


The seats are not the same. the controls will be on the wrong sides. If you insist on doing this yourself then unplug the wire harness connectors on each seat and remove the 4 bolts holding the seat rail to the floor. There will be plastic covers on the bolts that just pop off.

Mar 29, 2017 | 2003 Toyota Avalon

2 Answers

How can I convert drivers seat in my car to a bench seat


I'm having the same problem after a week in this car! I'm going back to the dealer to see if they have any suggestions. My other thought was to go to an upholstery shop to see if they can fabricate a cushion to make more of a "flat" seat to eliminate the bucket.

Mar 30, 2012 | 2012 Chevrolet Equinox LS 4dr SUV 2.4L...

1 Answer

I own a 2003 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN X My driver's seat has locked in one sitting position and the hand lever is not locked up, it moves freely but does not engage so that the back...


You should have a ratchet assembly at each end of the seat with a wire connecting the two. Look under the seat and see if when you pull the adjuster, it should release both sides at once. Also check if the wire is attached at all.

Jul 24, 2011 | 2003 Chevrolet S-10

1 Answer

How do I remove the power drivers seat in a 2003 Windstar. The support frame is broken and it needs to be replaced.


on the seat rail on either side of the seat on the floor itself there are 4 bolts,2 bolts on each of the front rails(1each) and 2 on the back of the seat rails.remove these bolts and disconnect all connectors for the power seat and remove the seat assembly.

Mar 15, 2011 | 1998 Ford Windstar

1 Answer

1983 S10 converted with 350 engine and 5 speed Camaro transmission. Do they make a bench seat with a curve in the center to accomodate gear shift clearance?


im sure you could find an aftermarket one if you search around on the internet, if not take any bench seat that you like and take off the bottom clear out some of the interior filling around where the shifter will be and pull the fabric more taunt where it will now be loose and pin to the underside replace the bottom of the seat and install. hope i helped :)

Sep 10, 2010 | 1983 Chevrolet S-10

1 Answer

1948 chevy thriftmaster bench seat adjusting


Not sure because this was 20 years before I was born,but the 70's erra seats has the handle with the fork/finger locking teeth with the return spring on the drivers side and there was a tiny hole on the inside where the wire goes.On the under side of the seat attached to the steel wavey springs there were loops just like hog rings that were used to route the wire to the locking lever on the other side.If this is the type of set up you could also use the hard plastic air line.Any heavy truck parts place will have it and it comes in many sizes.Would be easy to rout your wire thru.Well hope the helps and good luck.

Mar 26, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

How to remove rear seat in 1996 dodge ram 1500


REMOVAL & INSTALLATION
  1. Clamp the seat belts to keep them from retracting.
  2. Locate and disconnect seat wiring at the connector(s).
  3. Move front seats forward or back for access to the hold down hardware.
  4. Put the rear seats in the stowed position.
  5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
  6. Remove the hardware securing the seat.
  7. On split bench models, lift the center seat upward to clear attachment stud
  8. Remove the seat from the vehicle.
NOTE Do NOT activate the track adjusters once the fastening hardware is removed.
  1. Installation is the reverse of removal.

336abe0.gif


Fig. Disconnect the wiring from under the seat

36c62e2.gif


Fig. Seat track mounting hardware locations-typical


d95c538.gif

Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram


1589e1e.gif

Fig. Split bench seat assembly-Ram


616f086.gif

Fig. Bucket seat mounting components-Durango shown


851105e.gif

Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

Aug 31, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Rear bench seat


The only way to remove this is to unbolt it from the sliding rails. I do believe it would still leave some parts in the rails. This seat was designed to only slide forward and not be removed. If you insist on removing it, then you must unbolt it from the sliding rails...

Jul 12, 2008 | 1996 Nissan Quest

3 Answers

Rear seat removal 2000 merc Villager


fold top seat down first
then there is seat clip push seat forward with upward motion
this releases back floor clamps once released pull seat back this releases the front clamps then pull seat out of back door

Jul 06, 2008 | 2000 Mercury Villager

Not finding what you are looking for?
2003 Chevrolet S-10 Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...