Question about 1991 Dodge Shadow

1 Answer

When I push down on my brakes car dies?? I just had brakes done and a new booster

Posted by on

1 Answer

Take it back to the place that did the work
Wasn't done correctly,that is obvious

Posted on Nov 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cause of the acceleration hesitation and engine dying?


a simple test is to disconnect the vacuum hose to the brake booster and blank it off on the manifold side
if there is no problem, reconnect it and put your foot on the brake
if the problem is there --replace the brake booster
check all vacuum hoses including the vent controls and transmission actuator
if you haven't done it yet then run the fault codes for reports and that will tel you what should have been done first

Sep 03, 2015 | 2002 Pontiac Sunfire

4 Answers

1984 Honda Accord Brake Problem


well aside from the boosters you may also want to check the possitioning rotor and calipers. there is a possibility that something slipped, or leaked, check for brake fluids and try to trace where it is comming from.

the picture below shows how to disassemble the brakes of an Accord, the only special tool you will need is a ball joint fork to seperate the upper and lower ball joints. You have to remove the whole steering knuckle assembly to get to the bolts in back of the rotor and hub assembly.

b8487ef.gif
hope this helps

Aug 05, 2008 | 1984 Honda Accord

1 Answer

Step by step instructions for replacing brake booster on a 1999 Toyota Camry


its my pleasure to answer your question how to replace the brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How to remove brake booster on 1999 Toyota Camry


The following steps will help you to replace a Toyota Camry brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How do i replace the brake booster on a 98 Mercury villager


12 specific steps will help you :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the vacuum brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Sep 24, 2013 | Cars & Trucks

2 Answers

My brakes are hard to push down and it sounds like air is coming out of the brake pedal


This one I can be fairly certain of. It sounds like a rip in the vacuum power brake booster diaphram. Usually you just replace the whole power brake chamber, which includes the diaphram. You have to first remove the 2 bolts holding the master cylinder to the larger booster chamber, but you don't normally have to open any brake lines.
When replacing, make sure the brake pedal rod goes down the center of the new booster, and that there is sufficient clearance or freeplay in the pedal rod when done. (like .1" is all you need)
Should not have to bleed after done.

Jul 08, 2010 | 2002 Chevrolet Avalanche

1 Answer

When push brakes you have to push really hard to make them go in then the truck barely stops. Replaced the MC and bled the brakes now every time push brakes truck acts like its going to die. Brake light...


Sounds like you will have to bleed your brakes again, but thats not the problem og hard brake peddle, need to check your power brake booster, sit right in back of master cylinder, check make sure it has vacum going to it, also to test it with engine off, press on brake peddle three time, then state engine with foot on peddle, peddle should go down a few inches, also with engine of peddle should feel soft for three pumps, if you have none of this , power brake booster is bad.

Jul 04, 2010 | 1995 Toyota 4Runner

1 Answer

Spongy brakes


So long as the brake booster is working, test it by turning on the engine, press the brake pedal all the way down, then shut off engine keeping your foot on the brake pedal, if the pedal comes up slightly pushing against your foot then the booster IS working.

Did you BLEED the brakes??????

Mar 29, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Any info on changing a brake booster on a 1996 Sierra and also help trouble shooting a master cy. Thanxlinder


a defective master has just one common symptom, a soft sinking pedal.
Instructions Things You'll Need:
  • Nose pliers
  • Ratchet and socket
  • Ratchet extension
  • Slip joint pliers
  • Wrench
  • New cotter pin
    Removing the Old Brake Booster
  1. Step 1 Park your car in a safe place with enough room to work around the front and driver side of the vehicle.
  2. Step 2 Locate the booster push rod connected to the brake pedal.
  3. Step 3 Remove the cotter pin securing the booster push rod pin to the brake pedal using a pair of nose pliers.
  4. Step 4 Release the push rod pin from the brake pedal and slide the push rod off the brake pedal.
  5. Step 5 Unscrew the four mounting nuts off the brake booster studs using a ratchet, ratchet extension and socket. You should be able to see the four booster studs extending through the firewall, in front of the brake pedal.
  6. Step 6 Disconnect the vacuum hose from the brake booster, working from the engine compartment. Use a pair of slip joint pliers.
  7. Step 7 Remove the two nuts holding the brake master cylinder to the brake booster. Use a wrench or ratchet and socket.
  8. Step 8 Separate the brake master cylinder from the booster just enough to make room for booster removal.
  9. Step 9 Pull the brake booster off the firewall and remove it from the vehicle.
    Installing the New Brake Booster
  10. Step 1 Set the new booster in place by sliding the push rod and four mounting studs through the mounting holes on the firewall.
  11. Step 2 Slide the brake master cylinder flange over the two mounting studs on the brake booster.
  12. Step 3 Start the two brake master cylinder mounting nuts by hand to avoid damage to the threads.
  13. Step 4 Tighten the two brake master cylinder mounting nuts using a wrench or ratchet and socket.
  14. Step 5 Connect the vacuum hose to the brake booster.
  15. Step 6 Screw the four mounting nuts to the brake booster working from inside the vehicle. Start the nuts by hand to avoid damaging the threads.
  16. Step 7 Tighten the four mounting nuts using the ratchet, ratchet extension and socket.
  17. Step 8 Position the brake booster push rod over the brake pedal and slide the push rod pin.
  18. Step 9 Install a new cotter pin to secure the booster push rod to the brake pedal

Nov 20, 2009 | 1996 GMC Sierra

2 Answers

We've just had a big rain storm and I was out getting errands done when all of a sudden it was as if my power brakes were'nt working. It was very hard to push the brake pedal down, although I still had...


Sounds much like a vacuum leak; this would definitely cause rough running and the power brake booster is dependent on engine vacuum.
This should have turned on the 'check engine' light though -

Aug 19, 2009 | 2002 BMW 5 Series

Not finding what you are looking for?
1991 Dodge Shadow Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...