Question about 1989 Chevrolet Corsica

1 Answer

1988, 2.0 corsica. is the ignition coil at the bottom back of the motor.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,608 Answers

Yes.Just follow the plug wires.There are 2 coils.Hope this helps.Good luck.

Posted on Nov 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 88 chevrolet corsica. No spark at the plug wire put new coils / module on still no spark can the crankshaft position sensor stop it from getting spark and i checked all te fuses Bill


Yes the cam sensor could fail to send a signal to the ignition module, but a V6 engine does not use a cam sensor.
It does use a crank sensor.
You would need to know that the ignition module and coils have battery voltage, then you would need a book to give you the test procedures for the computer and crank sensor.

Mar 17, 2013 | 1988 Chevrolet Corsica

1 Answer

How do i install a ignition module to a 1996 corsica?


Ignition module is mounted to bottom of coil , remove coil , remove module from coil , mount new coil and replace to vehicle .

Jan 27, 2011 | 1996 Chevrolet Corsica

1 Answer

I have spark on plugs 2&3, but no spark on plugs 1&4, car is a 1993 Chevrolet Corsica. 4 clyinder motor.


There are 2 coil packs that send spark to the plugs. 1 covers 2&3 the other covers 1&4. the most likely problem would be a bad coil. I have had to change them on Corsicas and Berettas. If this persists. it is probably the ignition module that the coils bolt to.

Sep 29, 2010 | Chevrolet Corsica Cars & Trucks

1 Answer

How do I replace the ignition switch on my 1988 corsica?


you will need to pull the steering wheel to do this job
possibly available to rent from auto parts store
once wheel is off you need to remove lock ring by depressing it and removing clip ring. then remove turn signal assembly (4 screws) after this you should see the release screw ro the ignition switch. Is this a tilt column? If this helps get back to me a I can walk you thru it. dont forget to reply too - good luck
email is chromapr@wowway.com

Apr 26, 2010 | 1988 Chevrolet Corsica

1 Answer

Need plug to coilpack diagram for 89 corsica with 2.0 V 6 I diagnosaed the coildpak and its not working... Also what size screw is on this colipak..8mm or what cant seem to remove it....


1989 Chevrolet Corsica 2.8 liter V-6 VIN "W"

9391cfd.gif


1989 Chevrolet Corsica 2.0 liter L4 VIN "1"

ed4aa9c.gif


GM Corsica/Beretta 1988-1996 Repair Guide
Ignition Coil - REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Detach the 8 or 11-pin harness connector, as applicable, from the coil and module assembly.
  3. Remove the ignition assembly-to-camshaft housing attaching bolts.
  4. Carefully remove the ignition assembly from the engine.
If the spark plug boots present a problem coming off, it may be necessary to use a special removal tool, first twisting and pulling upward on the retainers.
  1. Remove the ignition coil housing-to-cover bolts/screws.
  2. Remove the cover from the coil housing.
  3. Detach the ignition coil harness connectors from the coil pack assembly.
  4. Carefully lift the coil pack out and remove the contacts and seals from the housing.
To install:
  1. Install new coil seals into the coil housing.
  2. Install the coil contacts to the coil housing and retain with petroleum jelly.
  3. Place the coil pack into the housing and connect the harness connectors.
  4. Assemble the cover to the coil housing and install the attaching bolts/screws. Tighten the attaching bolts/screws to 35 inch lbs. (4 Nm).
  5. Install the spark plug boots and retainers on the ignition assembly housing secondary terminals.
If the boots and retainers are not in place on the housing secondary terminals prior to installing the ignition assembly, damage to the ignition system may result.
  1. Position the ignition assembly to the engine while carefully aligning the boots to the spark plug terminals.
  2. Coat the ignition assembly-to-camshaft housing attaching bolts with an approved lubricant and install them into the housing.
  3. Tighten the attaching bolts to 16-19 ft. lbs. (22-26 Nm).
  4. Attach the harness connector to the ignition coil module assembly.
  5. Connect the negative battery cable.
  6. Start the engine and check for proper operation and performance.

Hope this help to solve ypur problem (remember comment and rated this post).

Apr 20, 2010 | 1989 Chevrolet Corsica

1 Answer

What is the firing order of the wires that go from the spark plugs to the coil pack or distrobuter for a 1988 4 cylinder chevy corsica


For the 2.0L:
Firing Order:
1-3-4-2
Cylinders:
1---2---3---4
(front of vehicle)
Ignition Connections:
----[4]
-------[1]
---------[3]
-----------[2]
(front of vehicle)

Feb 09, 2010 | 1988 Chevrolet Corsica

1 Answer

Need a wiring diagram from ignition module to coil to engine for a 1988 chevy corsica. Ive been replacing parts on this car for 6 months and it still runs like ****. It run good for one month now its...


This is for the 2.8L engine. Sometimes if it is hard to see, you can use a mirror and a flashlite. Aim the mirror in the direction of part your trying to look at, shine the lite in the mirror.
2.8-se0j5t3k3rpearckfykaa4pi-4-0.jpg

Jul 21, 2017 | 1988 Chevrolet Corsica

1 Answer

1988 chevy corsica 6 cyl suddenly running on 4


WET PLUD W/GOOD COMPRESSION IS USUALLY NO SPARK.YOUR ENGINE HAS 3 IGNITION COILS.EACH COIL CONTROLS 2 SPARK PLUGS.TRACE THE WIRES FROM THE BAD SPUGS BACK TO THE COILS .IF THEY ARE THE SAME COIL THEN U HAVE A BAD ONE OR CONTROL MODULE(UNDER COIL)

May 12, 2009 | 1988 Chevrolet Corsica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...