Question about Mazda 626

1 Answer

Where is the knock sensor located in a 2002 mazda 626

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 14,036 Answers

KNOCK SENSOR ON LOWER SIDE OF ENGINE BLOCK NEXT TO STARTER.

Posted on Nov 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Guy has 2002 Mazda 626 sadan his daughter ran the oil light is on it knocks but it drives what should i do ?


If the oil light is on and the engine knocks then there is major damage in the engine. Pull and replace the engine.

Apr 06, 2013 | 2002 Mazda 626

1 Answer

Were is the knock sensor on 2002 protege5 2.0L


The knock sensor is located under the intake manifold to replace do the following
Disconnect the negative battery cable.
Remove the intake manifold.
Disconnect the sensor connector.
Remove the sensor from the engine block.
Installation is the reverse of the removal procedure

Sep 28, 2012 | 2002 Mazda Protege

1 Answer

Mazda 626 2002 smells like burning rubber


This is not good. Sounds like the heater fan bearing and/or resistor is burning out. Not familiar with your heater fan location, but most will be removeable from engine compartment.

Just remove it and spin it by hand or hook auxillary power to it to test. Some autoparts stores can test it for you. Stuff a rag in the opening to block fumes if this must be driven for parts run.

Jan 27, 2012 | 1999 Mazda 626

1 Answer

Where is the ECT SEnsor located on a 2002 Mazda 626


Welcome to FIxYa.com


3a01f88.png


Regards, Lee Davidian


Thank you for using FixYa,com.

Oct 27, 2010 | 2002 Mazda 626

1 Answer

I need a diagram of the exhaust system on a Mazda 626


0996b43f80203328.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2000 MPV

1 PCM 2 Mass air flow (MAF)/intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Fuel tank pressure sensor 5 Engine coolant temperature (ECT) sensor 6 Crankshaft position (CKP) sensor 7 Camshaft position (CMP) sensor 8 Knock sensor 9 Heated oxygen sensor (HO2S) (front, LH) 10 Heated oxygen sensor (HO2S) (front, RH) 11 Heated oxygen sensor (HO2S) (rear, LH) 12 Heated oxygen sensor (HO2S) (rear, RH) 13 EGR boost sensor 14 Power steering pressure (PSP) switch 15 Main relay


0996b43f8020330c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2001 MPV

1 PCM 2 Mass air flow (MAF)/Intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Engine coolant temperature (ECT) sensor 5 Crankshaft position (CKP) sensor 6 Camshaft position (CMP) sensor 7 Knock sensor 8 Heated oxygen sensor (HO2S) (front, LH) 9 Heated oxygen sensor (HO2S) (front, RH) 10 Heated oxygen sensor (HO2S) (rear, LH)* 11 Heated oxygen sensor (HO2S) (rear, RH)* 12 EGR boost sensor


0996b43f8020330f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart- 2002-06 MPV

May 22, 2010 | 2004 Mazda MPV

1 Answer

Where is fuel filter located on mazda 626 2002 4 cylinder


Locate the fuel tank underneath the rear of the vehicle. It should be inline on the drivers side of the car. If not, it is underneath the hood on the fuel lines that lead to the fuel rail conected to the intake manifold.

May 01, 2010 | 2002 Mazda 626

1 Answer

2002 Mazda 626 Horn Fuse


Under the hood under a black cover. On the underside of the cover it will tell you which fuses are for what.

Jan 08, 2010 | 2002 Mazda 626

1 Answer

How to replace knock senor switch on 2002 mazda protege 5



Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

May 09, 2009 | 2002 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...