Question about 2003 Dodge Sprinter

1 Answer

Started fine , been running fine. It just died when moving around warehouse . will crank but will not start

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

My 2003 dodge`s high presher fuel pump was leaking on top.i did replaced a oil ring now it do not start at all.i took air from the line and it still donot start .what should i do now?

Posted on Dec 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My 2003 Chevy Silverado's engine died while driving, engine will crank but not start


The battery starter and alternator would only affect cranking.
Someone will need to find out if it is spark or fuel related to know which system to inspect.

Nov 23, 2015 | 2003 Chevrolet Silverado 1500

1 Answer

1992 toyota started fine but then stalled out and would not start back up?


If it felt like running out of gas it probably was, Check fuel delivery first your fuel pump possibly died.

Jun 24, 2012 | Toyota Celica Cars & Trucks

2 Answers

1990 Ford Ranger Stalling


if it were me I would start with the idle air controll sensor, this is a real humdinger on fords. also clean out your throtle body really good.

let me know

tepfy

Apr 22, 2009 | 1990 Ford Ranger SuperCab

1 Answer

I have a 93 altima that will crank but will not start...about a couple months ago i went to my work and shut off my car. it was running fine when i shut it off.. when i came back out and started my car...


this year model is notorious for fuel related probs...check the remainder of the fuel system, injectors, and the fuel pressure regulator also verify that the fuel pump is actually running and getting the correct amount of power to the pump itself..... it may not be bad just not getting enough power

Jan 24, 2009 | 1993 Nissan Altima

1 Answer

1993 altima will crank but will not start..


replace the distributor oil is leaking into the electronics of the distributor and shorting out pull cap back off and look and see if oil is leaking out

Jan 24, 2009 | 1993 Nissan Altima

1 Answer

1989 park avenue would run about 60 miles then die, could restart immediately, but would go about 4 to 10 miles then die again, could restart immediately but would repeat the 4 to 10 mile thing. A couple...


check harmonic balancer for slop back and forth,,,,these 3.8's have a crank posision sensor behind the balancer,that run off of the balancer,,,gthe rubber wears out and they start to flop around and timing gets messed up.../they cost around 100 bucks for a aftermarket,and if thats the problem,do yourself a favor and replace CPS while tour at it....good luck...Lee

Jan 10, 2009 | 1989 Buick Park Avenue

1 Answer

Truck won't start


this sounds like crankshaft position sensor, my Cherokee was ding same thing it ended up being crank shaft position sensor. this part costs about $50 and is easy to install.

Dec 02, 2008 | 1998 Jeep Cherokee

1 Answer

2002 chevrolet monte carlo


My car was doing the same thing. It would stall out while idling or even turning a corner. I ended up replacing a few sensors but the problem was the fuel injector pressure regulator. The check engine light never came on. It was leaking fuel through the vacuum side of the diaphragm. Disconnect the vacuum hose from the pressure regulator and if there are any traces of gasoline it needs to be replaced.

Sep 09, 2008 | 2002 Chevrolet Monte Carlo

Not finding what you are looking for?
2003 Dodge Sprinter Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...