Question about Pontiac Grand Prix

1 Answer

Is there ajustment for camber caster on the rear

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Pontiac Master
  • 975 Answers

From the factory,no,however,
There is a bolt kit available,in a few different sizes from 1 degree to 3 degrees I believe.This is for camber only,no caster adjustment is possible.
Also,alot of the alignment problem may be ride height,as the springs get weaker,the rear end sags and the camber goes negative. Often the camber can be corrected with a coil spring spacer .
You can tell if you were to put a jack under the center of the rear,take some weight off and you will see the camber come back.

Posted on Nov 06, 2010

  • buysellgb Jan 23, 2011

    DnC Sourcing is to make an Expert of developing products. ---> www.artdnc.com (82) 70-7893-2100)http://www.sourcingbuysell.com
    We have 15 years developing experiences and will implement the advanced products to our customer.
    Electronics, home appliances, sporting goods, medical products, smart phone, General Phones, machine equipment, cattle. Midsize engine
    * Mechanical design, tooling, product design, machine design, reverse engineering (image), product design, MOLD Analysis
    * Processor: AVR series, DSP, FPGA, ARM7, ARM9, etc.
    * Circuit design, PCB ARTWORK Use Program: ORCAD, PADS
    70% Motor Sales ---> www.buysellmotor.net, sourcing everything ->http://www.sourcingbuysell.com

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Caster and camber ajustment


Camber and Caster adjustment requires special equipment and shouldn't be attempted at home. Take the car to a service or repair center of your choice.

Jun 06, 2015 | 1997 Lincoln Town Car

2 Answers

What causes front tire wear on inside & outside edges


Under inflation. When the tire doesn't have enough air pressure, the center tends to be pushed up from the road. Thus causing outer wear on both sides. alignment problems cause wear on one side or the other. Over inflation causes the center of the tire to wear .

Aug 31, 2014 | Cars & Trucks

2 Answers

Wheel alignment specs


This is just a free chat room

We have no info like that

We are at home & use the site-- the same as you do

Apr 08, 2014 | 2014 Ford Fusion

1 Answer

I was told there is no adjustment for caster but they can correct front camber with camber bolts and it is 50/50 that may help caster . they want 350.00 to do the camber bolt but I'm risking the 50/50 what...


Camber adjust bolts mounted from steering knuckle to strut will NOT change caster. 0.3' degree difference in caster is acceptable, up to 0.5'degrees higher on right is preferable for road crown correction. 0.5'degrees higher on left may show a noticeable drift to right while driving.

Feb 18, 2014 | Hyundai Tucson Cars & Trucks

1 Answer

Toe adjustment camber caster


camber 0 to 1 degree castor 1 to 2 degrees and toe in 1/ to 1/4 inch as different roads are constructed differently with varying cambers (slope to the side for water run off) the wheel alignment is best set by a qualified wheel aligner shop to suit the local conditions

Dec 17, 2013 | 1991 Buick Park Avenue

1 Answer

How to replace the factory casper/camber equipment on a 1992 gmc 1/2 ton truck? I am told there are knock out that need to be taken out?


1. Original control arm does not allow adjustment of caster and camber. caster and camber may be adjusted only by using adjustment kit ( gm # 15538596 ) Raise vehicle, and support under lower control arms.
remove and discard upper control arm to frame bracket bolts, nuts and washer.

2. remove large washers welded to upper control arm frame brackets. remove wield beads from upper control arm brackets. grind area smooth. install adjustment cans to bracket.

3. install bolt,adjust caster and camber to specifications by rotating bolt head.

Dec 13, 2013 | Cars & Trucks

1 Answer

Left front ,camber adjustment how?


I don't see what year your truck is. On the newer trucks. There's adjustment cams on the lower control arms. One at the front and one at the rear mount. They adjust camber/caster.

Oct 10, 2013 | Dodge Ram 1500 Cars & Trucks

1 Answer

Wheel alignment


If the car is stock then I would run the caster at .05 higher on the right than the left to adjust for the crown of the road. the front alignment looks good other than I am not sure which one is camber and which one is caster. To adjust the rear camber on these cars you have to have a camber kit. From the angle I am seeing you don't have a camber kit. Also the only way to adjust caster on the civic is to shift the sub frame.

Jul 30, 2013 | 1997 Honda Civic

1 Answer

Caster adjustment for 1990 jeep yj wrangler


caster is adjusted at the rear of the lower control arms. Camber is fixed and cannot be adjusted by normal means (though special off-set ball joints are available to do that) Toe in is adjusted by turning the sleeves in or out on the tie rod ends. None of this should be done at home though crude adjustments can be made in order to get the front end reasonably straight. Adjustments are made on an alignment machine that allows precise adjustments to all you mentioned as well as front/rear tracking.

Mar 12, 2010 | 1990 Jeep Wrangler

4 Answers

I keep having to replace wheels on my car.... the wheels are wearing unevenly i took it to a guy and he says the that there is a bar under there that keeps the wheels strait up and that bar is bent so my...


was your car in a wreck since you have own it?
that would be the only way anyone could bend steering or suspension parts.if your tires are leaning out on top,
it would be a part called"lower control arm assembly",
if you stand in front of your car with the steering wheel straight,and your tires are pointing in on each side,or pointed out instead of straight,that would be a "tie rod "
there is an inner tie rod and an outer tie rod end.
you need to take your car to a shop that does alignments,and have them tell you exactly what is wrong,you can even get lower control arm assemblies
from a salvage yard.but do yourself a favor and don't take your car to a MONROE or MIDAS type shop,they are only there to sell and make commissions! Find a normal shop that the owner is the mechanic.

Nov 26, 2009 | 1998 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

562 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...