Question about 2001 Ford F150 Styleside SuperCrew

1 Answer

How to change the rear axel bearrings on ford f 1=150

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 975 Answers

Have to pull the diff cover,remove the small bolt that holds the pin,remove the pin . With wheels off ,push the axle in remove c-clip ,slide axle out. You will need a slide hammer to remove the bearing.(or pull both sides and drive out with a long piece of rebar from the other end)
Be sure to check the axle surface where the bearing rides,if is damaged the parts stores sell a repair bearing that makes the rollers ride in a different spot on the axle.(called "axle savers")

Posted on Nov 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a howling noise rear end only when I accelerate


The noise is most likely a worn pinion gear bearing. There are 2 bearings on the pinion. The diff will have to come apart to inspect/service the bearings

Jul 01, 2015 | 1996 Ford Ranger SuperCab

1 Answer

Rear Axel Bearings


What kind of vehicle do you have?

Feb 23, 2014 | Chevrolet Cars & Trucks

1 Answer

Is there something more to removing the front hubs of a 09' focus then just pushing the axel out of the bearing?


The 3 or 4 bolts at the back side of the steering knuckle
it is bolted to

Have to loosen the bottom ball joint I believe in order to get the axle out

Mar 07, 2013 | 2009 Ford Focus

1 Answer

Rear wheel bearing


if its like the 99 winstar:

safely support the van, remove rear wheel, remove brake drum, remove grease cap. remove caged locknut assembly (38mm socket i think.) then pull the hub assembly from the axel. you may need to cut away the inner race if the bearing falls apart. clean axel, apply alittle anti size compound, then push on the new hub assembly. tighten down the hub nut to specifications (should be on the leaflet in the new bearing package), install dust cap, install drum, install wheel, lower and drive :)

May 25, 2010 | 1998 Ford Windstar

1 Answer

How to replace rear axle seals


if the seal (s) is leaking you may have a bad bearing... to change.. remove the rear end cover, reach in pull the c clip on left or rt side. pull the axel out the side, use bearing puller to pull the old bearing, install new replacement bearing seal, put in axel, replace clip, reinstall rear cover, sealing properly, fill with rear gear lube to level of fill hole. get a chiltons manual for pictures and more detailed help.

Mar 10, 2010 | 1987 Chevrolet Caprice

1 Answer

I have movement in the rear wheels on a 2003 Ford Mustang.Do I need to change the wheel bearings? How do I remve the hub?


Sounds as though your bearing could be bad, does your Differential have a cover on the back ?If so you'll have to remove it and remove the retainer rings (1) on each side of the inner axel .Then you should be able to remove the axels,but still may have to remove the Brake back cover also .Notice how much gear lube is left in the housing when you remove the cover . Don't forget to also replace the dust seals as well .

May 02, 2009 | 2003 Ford Mustang

1 Answer

Rear wheel axel Ford F150 2002 how do I dismantel it to check if it is a bearing, making a clunk sond , parked as it has gotten, worse. I have very little money and I would like to fix it myself.


check for a propshaft UJ worn first vehicle up in air wheel free then grasp front and rear of each joint in turn and give it twist ,iam pretty sure this has gone and not the pinnion/crownwheel.

Nov 18, 2008 | 2002 Ford F150 Regular Cab

Not finding what you are looking for?
2001 Ford F150 Styleside SuperCrew Logo

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...