Question about 1994 Buick Roadmaster

1 Answer

Rear suspension air compressor is not coming on. Checked fuse and it's ok?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 528 Answers

Locate and test the relay for the compressor. Look under the hood for a fuse /relay block and look inside the cover for which relay is what.
Good luck!

Posted on Nov 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 lincoln navigator air suspension leaks down after rising up


You may have a crack in a line somewhere. You hear it cycling while driving because the height sensor is telling it to lift because it's loosing air somewhere. I'd replace those o-rings first.

Jul 02, 2017 | Cars & Trucks

1 Answer

Air suspension will not come up, compressor is not


Ok lets try this from the top,

Check the boot/trunk for the Air suspension switch make sure it accidently hasnt been turned off.,

You said you checked the fuses make sure you pulled it out and checked it not just glanced to double check,

Go to the engine bay and open up the fuse box above the battery Swap the horn and Air suspension relay *Marked on box* around and try the horn, if the horn doesnt work you found your issue and a new relay is needed.

If no avial i point you to this tech artical done by Lincoln owners for other owners theres alot of other tech tips to i'd suggest book marking the site

http://www.lincolnsonline.com/tech/00061.html


Nov 07, 2009 | 1991 Lincoln Town Car

1 Answer

Where can i get a copy of the parts that make up the air suspesion of my 2001 grand marquis. sometime it works and other time it will not.


Vehicle Dynamic Suspension The vehicle dynamic suspension consists of the following components:
  • Rear air suspension control (RAS) module (5A919)
  • Snorkel
  • Drier
  • Air compressor (5319)
  • Air suspension switch (5K761)
  • Solenoid valve (5311)
  • Air spring (5560)
  • Air suspension height sensor (5359)
  • Air line
------------------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Restricted suspension movement
  • Excessive vehicle load
  • Cut, severed, or crimped air line(s)
  • Damaged air spring(s)
  • Height sensor damage
  • Height sensor mounted incorrectly, disconnected, or damaged
  • Central junction box (CJB):
    • Fuse 5 (15A)
  • Battery junction box (BJB):
    • Fuse 8 (30A)
  • Loose or corroded connectors
  • Air suspension switch OFF


The air suspension control module is diagnosed using Super Star II Tester 418-F045 (007-0041B) or equivalent.
The test connector used to communicate with the air suspension control module is located on the RH side of the luggage compartment.
When the tester is connected, the engine is started and the HOLD/TEST button is latched down, the air suspension control module will respond sending a code 10 to the Super Star II Tester which represents "Diagnostics mode entered." If diagnostic trouble code (DTC) 10 is not displayed, go to Pinpoint Test A.
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index
Condition Possible Sources Action
  • No communication with the air suspension control module
  • CJB Fuse 5 (15A).
  • BJB Fuse 8 (30A).
  • Circuitry.
  • Air suspension control module.
  • GO to Pinpoint Test A .
  • Unable to enter auto test
  • Air suspension control module.
  • Circuitry.
  • GO to Pinpoint Test B .
  • Rear air suspension does not respond to load changes
  • Circuitry.
  • Air compressor.
  • Air compressor inlet tube.
  • Air compressor drier.
  • Air suspension height sensor.
  • Air suspension control module.
  • GO to Pinpoint Test C .
  • Rear rides low/high
  • Circuitry.
  • Air spring solenoid.
  • Air suspension height sensor.
  • Air suspension control module.
  • GO to Pinpoint Test C .
  • Poor ride quality
  • Circuitry.
  • Air springs.
  • GO to Pinpoint Test C .
  • Air suspension warning indicator ON
  • Air suspension switch OFF.
  • Place the air suspension switch in the ON position.
  • Air suspension control module.
  • Circuitry.
  • GO to Auto Test.
  • Instrument cluster (conventional cluster) or lamp warning module (electronic cluster).
  • REFER to Section 413-01A (conventional cluster) or REFER to Section 413-01B (electronic cluster), or REFER to Section 413-01C (natural gas cluster).


Sep 25, 2009 | 2001 Mercury Grand Marquis

3 Answers

Air suspension problem compressor does not turn on to fill up air bags. have checked all fuses, all are ok. checked compressor it is ok but still not starting.any suggestions


Check the induction coil of the rectifier. See if sufficient charge is being developed to start compressor. If this initial surge is being delivered via any capacitor, then have that checked too.Since the compressor is not starting finally check the compressor by giving it power directly from the battery, appropriately stepped down if necessary.........sodeep

Jun 14, 2009 | 2004 Lincoln Town Car

5 Answers

Air Suspension for 2004 Hummer H2


hummer h2 hydraulic keeps running depleting battery.

May 22, 2009 | 2004 Hummer H2

3 Answers

Rear air suspension compressor not engaging.


what year? here's 2003 rear air only info, not 4 wheel air.

you have a fuse panel in truck and 1 under hood.




Visual Inspection Chart Mechanical Electrical
  • Restricted suspension movement
  • Excessive vehicle load
  • Cut, severed or crimped air line(s)
  • Unmounted height sensor
  • Damaged air spring(s)
  • Open fuses:
    • Central junction box (CJB) Fuse 4 (15A), 6 (5A) and 20 (5A)
    • Battery junction box (BJB) Fuse 109 (50A)
  • Loose, corroded or disconnected connectors
  • Air suspension switch is in the OFF position
  • Damaged solenoid valve(s)

  • compressor is inoperative
  • BJB Fuse 109 (50A).
  • Air compressor assembly.
  • Circuitry.
  • Air suspension relay.
  • Go To Pinpoint Test P .



----------------------------------------------------------------------------

The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.

Air Suspension Switch
The air suspension switch supplies power to the air suspension control module. Without the air suspension control module receiving this power, the load leveling system is inoperative and will not react when the rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off the air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
Air Compressor
The RAS air compressor:
  • consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • is a single cylinder electric motor driven unit that provides pressurized air as required.
  • is powered by a solid state relay which is controlled by the air suspension control module.
  • passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • air drier has a single port.
  • air drier may be replaced separately.
  • incorporates a snorkel that may be replaced separately.
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • has a 1,103 kPa (160 psi) internal relief valve.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the air suspension control module determines lowering is required.
  • provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
  • is replaced with the air compressor as a unit.
Air Spring
RAS vehicles use air springs in the rear. The air springs provide a varying spring rate proportional to the systems air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system air. Increasing air pressure (compressing) raises the rear of the vehicle while decreasing air pressure (venting) lowers the rear of the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the air suspension control module.
The two air springs support the conventional rear leaf coil springs.
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing the vehicle and related components.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
Solenoid Valve, Air Spring
s2j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Never rotate an air spring solenoid valve to the release slot in the end cap fitting until all pressurized air has escaped from the spring to prevent damage or injury.
The air spring solenoid:
  • allows air to enter and exit the air spring during leveling operations.
  • is electrically operated and controlled by the air suspension control module.
  • is only installed as a unit.

Apr 18, 2009 | 2003 Lincoln Navigator

2 Answers

1997 lincoln continental air suspension


there are 2 fuses for the air suspension module fuse #28 in the inst panel fuse box and fuse #22 in the power distribution box in engine compartment make sure the fuses are good the module controls the air susp and the variable steering if the fuses are ok you will have to see if there is power at the module pins # 1, 36, 37, 56, 57, 58

Dec 08, 2008 | 1997 Lincoln Continental

1 Answer

Air suspension not working


on the passenger side inside the wheel well there is a high current relay for the air compressor it is a silver metal relay assy 4 wire plug two smaller wire are the relay power two larger wires are compressor feed. if you jump the two larger wires and the compressor works check the smaller wires for power and ground if ok the relay is bad. usually these relays go bad due to compressor drawing high current and usually need to be replaced

Nov 26, 2008 | 1998 Ford Expedition

11 Answers

No air reaching air bags/compressor does not come on when car turned on


This is a very common problem with all Lincolns. The air ride suspension are marketed as a luxury-comfort item but most do not know that they have a 100% failure rate and are designed to fail as shortly after the warranty expires as possible. The air bags that support the weight of the vehicle are not designed to withstand temperatures below 40 degrees or above 94 degrees and are very prone to dry rot. Once the bags start getting tiny cracks and leaks they start overworking the compressor. (Picture trying to blow up a balloon with holes in it.. you will try for as long as you can but will ultimately have to give up) These air ride systems can be very difficult to accurately diagnose the first time and consequently very expensive. Most people seem to be converting to a passive suspension system these days as the ride quality is too similiar to notice a difference and the reliability is paramount. http://www.strutmasters.com offers a high quality conversion kit that utilizes powder coated American steel coil springs that are actually designed to last the lifetime of the vehicle. http://www.strutmasters.com/lincoln-suspension-parts-s/1.htm there is a direct link to the Lincoln page. I hope this helps save some of you a little bit of grief and a lot of money in the long run!!

Aug 24, 2008 | 2004 Lincoln Town Car

Not finding what you are looking for?
1994 Buick Roadmaster Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...