Question about 2008 Toyota Yaris Sedan

Open Question

How to replace entire headlight housing for 2008 yaris sedan, Headlight housing is broken, ordered new one now how to remove

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

NJFIRESTORM
  • 84 Answers

SOURCE: HEADLIGHT REMOVAL 2008 VW BEETLE

there's a tab on the plastic ring that you need to pop, and then wiggle the whole light assembly out and disconnect the wires

access for the bulbs is a panel you undo at the back of the light assembly, and the low-beam bulb is the first one you encounter when you reach in. (H1 should be the bulb)

putting it back in requires even more wiggling, as you tighten the plastic ring and lock it in place (pay attention that you get the light back in flush to the body work)

Posted on Sep 15, 2008

motor1258
  • 6674 Answers

SOURCE: need to replace driver's side headlight in 2004 dodge SX2.0

No. Just twist black locking retainer about half turn counterclockwise (left), remove it & wiggle bulb out. replace bulb without touching glass part of it which shortens the life if you do. Add a little vaseline to Orange O ring, to make it pop back in, after you make sure tabs on bulb are aligned with ones in the hole of housing. You may need to wiggle it back in too. Put retaining ring back on, turn clockwise until it locks, plug wire connector back in to back of bulb, until it snapps onto catch on bulb and your good to go.

Posted on Dec 13, 2008

  • 1 Answer

SOURCE: Removal of headlight housing to replace lowbeam bulb.

found this online- haven't tried yet though--
How do you change a headlight bulb on a 2003 Toyota Celica GT? Under the plastic covering the headlight there is a lot of fog and condensation and I want to clean it off, so how do I take off the plastic that covers the headlight?

  • 9 months ago
Seem to be seal is wear off
already on the front cover
The way to open that
1. There is four screws at the back of
the headlights and unscrew them
2. Pull the headlight and dry it
by wiping or heat of the sun or
anything that can release the fog
3. Buy silicon and seal the headlight
gap with silicon and let it dry for a hour
This will help kept away fog
and condensation for sure

Posted on Dec 17, 2008

  • 2 Answers

SOURCE: can't adjust 2004 Ford Expedition headlight

I had a similar problem on my 04 expedition. I just bought it and the headlights were aiming too far down. A rather larger gap was noticeable between the headlight and the hood. The so called adjustment bolt did nothing. I removed the headlights and found 2 issues. On the adjustment bolt there is a washer. Make sure when you re-install the headlight the washer sets on top of the plastic slot and is visible when looking down behind the headlight. Without the washer being in the correct location it will not tighten the headlight in place.
Second I found the adjustment bolt adjusted nothing. It merely tightened the headlight in place. What I had to do was to loosen this bolt and physically move the headlight into place and the re-tighten the bolt. Hence the slot is the adjustment. Turning the bolt CW or CCW did not move the headlight.
I tried several things trying to figure why the lights would not move until I realized I could move the light with my hands and tightened them in place using the adjustment bolt.

This may not be your issue but I found the owners manual instructions to be useless.

Posted on Jan 02, 2009

bunnydawg
  • 5158 Answers

SOURCE: 2000 CHRYSLER CONCORDE HEADLIGHT BULB REPLACEMENT

thought i already answered this... must have been for someone else... you should be able to access the bulb from within the engine compartment... if it's on the side of the battery you may have to remove it. do not touch the bulb with your fingers as that shortens the life of it.

Robert

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm looking for the easiest way to change the bulb of the headlight on the passenger side of a 2008 Pontiac G6


i think right behind the lens housing there it 2 plastic rods pull up on them then is should slide out to get to the bulb

Mar 24, 2012 | 2008 Pontiac G6 Sedan

2 Answers

How do i change head lights on a pontiac g6


Which ever side you are looking to change, you will find an 8 to 10mm bolt. Once you remove that bolt located near the headlight housing, you lift up on the bar that you just took the bolt off of, then once you have the bar up, gently pull out the headlight housing starting from the inside pulling straight out, thats it. Remove the bulb, and replace in reverse order.

Mar 14, 2011 | 2008 Pontiac G6

1 Answer

How do i replace the headlight on a 2008 outlook


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Oct 31, 2010 | 2008 Saturn Outlook

4 Answers

How to change a headlight bulb in a saturn aura?


Access to change the headlamp bulbs is through the wheel well. The recommended method is to remove the front tire and then the plastic inner fender liner. Once removed, you'll have easy (more or less) access to the rear of the headlamp housing.

Apr 27, 2010 | 2007 Saturn Aura XR Sedan

2 Answers

How do you change front headlight blub 2008 sonata


how do you change front headlight blub 2008 sonata

Nov 28, 2009 | 2008 Hyundai Sonata

1 Answer

Replacing my headlight bulb in my kia amanit 2004


  1. Open the hood of your KIA Amanti and look behind the headlight that has gone out. Locate the round knob on the back of the headlight.
  2. Turn the knob counterclockwise 1/4 of a turn and gently remove it from the back of the headlight. Carefully remove the electrical cable within the headlight housing that is attached to the back of the headlight bulb.
  3. Locate the metal clip that holds the light bulb in place by pushing the clip arm straight in and sliding it down. Remove the bulb from the headlight housing.
  4. Replace the old headlight bulb with new bulb. Secure it by sliding the metal clip up to hold the bulb in place. Reattach the electrical cable and replace the round knob to the back of the headlight housing.
  5. Turn on the headlights to verify that they are in working order.

Nov 03, 2009 | 2004 Kia Amanti

1 Answer

How to Change the Headlights in a 2008 Lancer ES


You shouldn't have to remove the entire headlight assembly to change the bulbs; They should either twist out, snap out, or have a spring clip that holds the bulbs in.

Mar 31, 2009 | 2008 Mitsubishi Lancer GTS CVT Sedan

1 Answer

Audi A6 Xenon headlamp bulb change - UK Offside





Headlights, Removing and Installing

Removing
  • Remove front bumper.
  • Remove both Torx bolts (T30) -1-.
  • Remove interior Torx bolt (T30) using 1/4"-Torx-bit insert and extension.
NOTE: If necessary, use magnet to remove bolt.

  • Disconnect multi-function harness connectors for headlights.
  • Turn headlights -2- toward center of vehicle and remove from chassis toward front.
Installing
Installation is reverse of removal, noting the following:


  • Adjust dimension -a- via plastic bolt at new headlight.
NOTE: Determine dimension -a- at plastic bolt of old headlight, when being replaced
  • Engage headlight in area of center of vehicle in guide -2- via pin -1-.
  • Always align headlight according to contours of chassis (gap dimensions) and secure.
  • Adjust headlight after installing.
Tightening torque

Component Nm
Headlights to lock carrier 6



Repair Kit For Headlight Housing, Installing

NOTE:
  • Headlight mounting tabs that have broken off can be replaced by installing the repair kit. Complete replacement of the headlight is therefore not necessary.
  • Different repair sets are available for the left and the right headlight.
  • Remove headlight with broken mounting tab.
    • Remove remains of the broken mounting tab -1- at location marked with the arrow.
    • Place mounting tab -2- of repair set onto the edge (arrow) of the headlight housing and secure the tab with two screws -3- from rear.

Feb 09, 2009 | 2004 Audi A6

1 Answer

Driver's side Headlight Bulb Replacement


Do you mean the entire headlight assembly or just the bulb?
If it's the entire headlamp look at the new one to see where the fastening points are, the grill may have to be removed and also the parking lamp lens, if it's just the bulb it's easy Open your hood look at the back of the headlight assembly and twist the bulb holder ring to release it. Good Luck To You

Jan 20, 2009 | 2008 Honda Element

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...