Question about 1994 Ford Probe

1 Answer

Door panel how do i remove the window hand crank so i can remove the front door panel? i'm wanting to replace the speaker

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There is a clip that holds it in place...and theres a special tool that u can by..... but i find that 2 butter knifes work just as good..... the clip is a horse shoe thing....and if they installed it correctly....then the opening of the clip should be facing towrds the knob that spinns in your hands when opening.....so take the 2 knifes and go down and push the clip out........ it might not come out the first try so keep trying but it will slide off....

Posted on Jun 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the wing mirror (power adjust & power fold) on the ford f250 super duty?


Roll the window down first, you will need 2 hands. Pull the small cover off that is at the top front of the door pannel. You will then disconnect the wire connector and remove the three 11mm nuts that are holding the mirror in place. Pull mirror out and replace.

If you dont have just that little pannel you will have to remove the door pannel. If you dont have power windows pull the cover out on the window crank and move it to the side, there will be a screw holding the crank in place. Remove it. If you do have power windows remove the window control switch plate (it will just pop up using a small screwdriver) and disconnect the wires. If equipped, remove the front door trim panel reflector or the courtesy lamp lens. Then remove the screws. DO NOT pull directly outward on the door pannel, something will brake. Remove the front door trim panel by pulling it straight upward.Lift and remove the front door trim panel. Then the nuts holding the mirror will be visible, remove and replace the mirror.

Dec 07, 2010 | 2000 Ford F250 Super Duty Crew Cabs

6 Answers

2008 Cobalt - Front speakers not working and no audible turn signal. Both stopped working at the same time.


In my 2008 Cobalt, the front speaker in the driver door went inoperative - no turn signal noise, no warning chimes for door open with key in, seatbelt chime, low fuel chime, and of course, no music. All of those sounds come through the speaker. I switched the driver door speaker and the passenger door speaker, and now I have all of those noises back.

If you have manual roll down windows, you'll have to buy a special tool to remove a little clip that's behind the roller handle. This tool was included in a kit for about $7 that I bought at Harbor Frieght, but you might be able to find the kit at other auto parts stores. Google "removing window crank" and you should be able to locate a video that shows how to get it off.

Anyway, I switched the speakers and now we just don't have music coming out of the passenger door speaker, but at least we have all of the warning chimes and turn signal clicking noise again.

The dealer wanted almost $200 for a new speaker and to replace it (labor). Rediculous.

Jul 20, 2010 | 2008 Chevrolet Cobalt

1 Answer

Need to remove driver side door panel?


  1. Disconnect the negative battery cable.
  2. If equipped with an accessory switch panel, carefully pry the switch panel up and away from the door panel. Tag and disconnect the switches from the panel.
  3. On 1981-86 models, remove armrest attaching screws.
  4. On 1987-96 models, remove the retainer screws secure the pocket in the molded armrest on the door panel.
  5. If equipped with crank type windows, remove window crank handle with the appropriate clip removal tool.
  6. If equipped with manual remote mirrors, remove the control knob bezel.
  7. Remove inside door handle cover attaching screw and trim plate.
  8. If equipped with door mounted speakers, remove the speaker, and disconnect the speaker wires. For speaker removal and installation steps, refer to .
  9. Remove all external screws securing the door panel. Insert an appropriate prytool between the door panel and door frame to remove the hidden clips securing the panel.
  10. Holding door panel vertical lift straight up to release the upper clip.
  11. Inspect all retaining clips and replace any broken or missing pieces.

To install:
  1. Position the door to the door and carefully press on the retainer clips to engage. If a clip will not engage, inspect the mounting hole behind the panel to make sure the clip is properly aligned. Install any panel-to-door retainer screws.
  2. If equipped with crank windows, attach the washer and crank to the window regulator stud.
  3. On 1981-86 models, attach the armrest to the door using the retainer screws.
  4. On 1987-96 models, insert the armrest pocket and secure in place with retainer screws.
  5. If equipped with door panel mounted speakers, attach the speaker wires to the speaker and secure the assembly to the door panel.
  6. If equipped with remote cable mirrors, attach the control knob to the door panel with the retainer bezel.
  7. If equipped with an ashtray, insert the holder assembly, and secure in place with retainer screws. Install the ashtray to the holder assembly.
  8. Position the door handle trim panel around the door handle assembly, and secure in place with the retainer screw.
  9. If equipped with accessory switch panel, attach the harnesses to the switches, and press the accessory plate into the door panel.
  10. Connect the negative battery cable.
  11. Check and make sure all panel components function correctly.

Apr 03, 2010 | 2002 Ford Explorer Sport Trac

1 Answer

How to remove the inside door panel from a dodge 2005 2500 pick up


FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

2 Answers

I am looking for a diagram or picture as to how to get to the speakers to replace them on a 97 villager??


Section 15-03: Speakers 1997 Villager Workshop Manual DESCRIPTION AND OPERATION Radio Speakers All vehicle sound systems are equipped with radio speakers (18808) located at all four corners of the vehicle. The radio speakers are mounted in the RH front door (20124) and LH front door (20125), as well as behind the quarter trim panels (31012) in the rear of the vehicle. The Ford Super Sound Audio System has the addition of a subwoofer mounted in the RH quarter trim panel.
-----------------------------------------------------------------------------------------
Radio Speakers, Front Door Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 .
Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  2. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
  3. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  2. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  3. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  4. Remove the front door trim panel.

Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
  1. Remove the four front door radio speaker screws.

May 20, 2009 | 1997 Mercury Villager

2 Answers

Replacing speakers in Mitsubishi Galant


If the car is an 03 galant it is very simple to remove.
DRIVER SIDE:
Remove the window crank if it is not Electric Window.
Remove the Screw that holds the "Open Door Handle" cover.
Remove the Screw that holds the "Pull Handle Pocket"
Remove both plastic covers.
Remove all 3 hidden crews that have a plastic cover over them.
One is toward the front of the door top and the other two are toward the rear of the door top and bottom side.
Carefully pry around the door trim panel to disengage it from th retaining clips, along the sides and bottom. If you have electric windows, disconnect the if from the door trim to access the speaker. Same procedure for both doors.

Feb 25, 2009 | 2003 Mitsubishi Galant

1 Answer

Change window gear on 99 civic


this is from a 97 civic should be the same. remove the door panel. remove 1 screw and pull handle, remove 1 screw and plastic cover over door opener handle. remove speaker cover and three screws underneath. remover window crank. then remove the door panel (held on with plastic plugs...just pull panel toward youself).
8e9dc4a.jpg
e838839.jpg
to remove the regulator ("window crank gears") Remove the glass held in with two 10mm bolts. The regulator itself is held in with six 10mm bolts. Remove these bolts and remove the regulator. (installation is reverse). Note: pay attention to the Idler arm track (highlighted in green) I think this one is directional (the front has to be at the front and the back has to be at the rear)

5a5e384.jpg

Feb 23, 2009 | 1999 Honda Civic

1 Answer

Need to remove window crank 2004 hyundai accent


Your Local Auto Parts Store has the Tool that you need for this Removal. Some of them will let you Rent it instaed of paying the 50.00 Bucks for the Tool.

Jan 24, 2009 | 2001 Hyundai Accent

1 Answer

97 VW Jetta right rear power window off track


There should be six or seven allen wrench screws around the edge of the door panels. Loosening these releases the retaining clips inside. You will then want to remove the manual window crank if you have one by laying two fingers flat on the door panel and pushing the ring around the base of the crank sideways. You might have to rotate around this as it only pushes one way. Next you will have to remove the two large golden screws directly under the door panels handle. If you have rear door panel speakers you will have to politely pry off the speaker grill with a flat blade screwdriver and remove the speakers four screws and the wire clip from behind the speaker. You will also have to unscrew the door lock post. Then you should be able to lift the door panel up to release the top lip of it from the door.

Dec 29, 2008 | 1997 Volkswagen Jetta

1 Answer

Removing the front door panel


there a special tool to remove that clip or you can use a women nylon slip the nylon beetween the handle and door panel and move it be carefull that clip fly off when it loose thanks pierre

Oct 08, 2008 | 1999 Chevrolet Malibu

Not finding what you are looking for?
1994 Ford Probe Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...