Question about 1992 Chevrolet K1500

1 Answer

Replace carrier bearing on driveshaft - 1992 Chevrolet K1500

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 320 Answers

The carrier bearing is a press off and press on bearing. drop the 2 mount bolts remove the 2 rear u bolts and take the front half to the auto parts store. takes about 2 minutes to presss on and off

Posted on Nov 06, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 563 Answers

SOURCE: how do I replace the driveshaft bearing support?

You jack up the truck, and support it on jack-stands. (no wheel must touch the ground, for safety).
Remove the two front tires for visibility.
Put the tansmission in neutral and apply the handbrake.
Get under the truck and in the area of the support-bearing, mark the position of the driveshaft to the flange, which has 4-bolts.
Remove the 4-bolts.
Pry off the driveshaft with a flat-end screwd-river.
Remove the bolts holding up the support bearing.
Drop it down and pull off the support bearing.
Reverse these procedure for installation.

Posted on Nov 26, 2009

gladys_neal
  • 334 Answers

SOURCE: 2005 ford escape 3.0l AWD XLT - DRIVESHAFT CARRIER

if there is some one in your area that balances driveshafts they can change just the bearing for you

Posted on Nov 10, 2009

  • 4088 Answers

SOURCE: mid ship bearing on driveshaft needs replacing.

Not unless you bend the tube. You will have to disassemble at least one U-joint--keep track of how it came apart and all of the little needle bearings in the cups on the end of the cross--keep everything clean. Fresh grease will help keep things together when putting it all back.

Posted on Jul 19, 2009

  • 139 Answers

SOURCE: how do you get the carrier bearing off the

You have to take it to a shop and have it pressed off.

Posted on Sep 04, 2009

  • 2 Answers

SOURCE: need to replace driveshaft carrier bearing, will not come off transmission end.

First mark the relationship of the two yokes and then remove the universal joint. Now that's done remove the retainer clip from the top of the slip yoke and gently tap the slip yoke out being careful not to damage the splines on the shaft. the bearing that ins on there is pressed in so (A) you can bring it to someone with a press or (B) use a gear/ pulley puller. If you attempt this take your time and have patience don't break anything and think safety first.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Loud humming noise


Could be carrier bearing(s), worn gears, or bad driveshaft joints.

Jul 18, 2016 | Cars & Trucks

2 Answers

I have a 96 camaro and I need to replace my carrier bearing. Where can I find one?


I am not sure your car has a carrier bearing, but if it did it would be located on the drive shaft between the transmission and rear end of the car.

Apr 22, 2013 | 1996 Chevrolet Camaro

2 Answers

What is the part number for a carrier bearing on 1995 chevy camaro


(a little late in responding - but maybe someone will need this info).

If you mean the carrier bearing on the driveshaft - then you must have a v6 model. I would advise to skip replacing it and instead purchase a 1pc shaft (no carrier bearing). The cb is located near a Hi-Speed CV Joint which make changing the carrier a little difficult.
A new replacement 1pc driveshaft costs about $225.00
The carrier bearing itself may run $40-$140. ( http://www.fortwayneclutch.com/index.php/driveshaft-parts/carrier-support-bearings/gm/1993-2002-chevy-camaro-v6-pontiac-firebird-v6-carrier-bearing-new-f-body-carrier-bearing-for-v6-models-pn-s-3r80-40.html ) - for reference...
You could also check a junk yard for a 1pc oem shaft (most shafts there are bent or have bad uj's and will cost $$ to have fixed )
>1994-2002 f-body models all have the same length from the seal of the transmission to the center of the uj @ the diff.
>when looking for an oem 1pc shaft you will find them in Steel and Aluminum. Slight differences in length when measuring center to center of the universal joints ( 40 7/8" - 40 1/2" ) - but the slip yokes vary in length, weighted / non-weighted..etc = this will make it appear the the shafts are different.
>>watch out for oem shafts with the weighted slip yoke from manual 6spd v8 models. This slip yoke may hit the trans/exhaust mount that is used on v6 models.!!

Jan 13, 2013 | 1995 Chevrolet Camaro

1 Answer

Ford escape 2006 awd driveshaft carrier bearing stud replace


if flush break than drill and use a remover can buy a remover at most hardware-home-auto stores ====if their is enough to grab stud use heat carefully and a stud tool -vice grip or anything that will grab the stud to remove it

Jan 12, 2013 | 2006 Ford Escape Hybrid

1 Answer

My carrier bearing is bad in my 96 firebird and I can't find another anywhere. No one has heard of a 2 part driveshaft in my car. Can I replace it with a solid driveshaft? Or do you know where I can find a...


If you mean the carrier bearing on the driveshaft - then you must have a v6 model. I would advise to skip replacing it and instead purchase a 1pc shaft (no carrier bearing). The cb is located near a Hi-Speed CV Joint which make changing the carrier a little difficult.
A new replacement 1pc driveshaft costs about $225.00
The carrier bearing itself may run $40-$140. ( http://www.fortwayneclutch.com/index.php/driveshaft-parts/carrier-support-bearings/gm/1993-2002-chevy-camaro-v6-pontiac-firebird-v6-carrier-bearing-new-f-body-carrier-bearing-for-v6-models-pn-s-3r80-40.html ) - for reference...
You could also check a junk yard for a 1pc oem shaft (most shafts there are bent or have bad uj's and will cost $$ to have fixed )
>1994-2002 f-body models all have the same length from the seal of the transmission to the center of the uj @ the diff.
>when looking for an oem 1pc shaft you will find them in Steel and Aluminum. Slight differences in length when measuring center to center of the universal joints ( 40 7/8" - 40 1/2" ) - but the slip yokes vary in length, weighted / non-weighted..etc = this will make it appear the the shafts are different.
>>watch out for oem shafts with the weighted slip yoke from manual 6spd v8 models. This slip yoke may hit the trans/exhaust mount that is used on v6 models.!!

Jul 22, 2012 | Cars & Trucks

1 Answer

Is a 2004 ford f-150 2wd carrier bearing.. ( mid-mount bearing ) on driveshaft replaceable, or do i have to replace entire driveshaft?


it is replaceable
normally it comes complete in the rubber mount
you will have to undo the drive shaft flange at the bearing
remove the drive shaft and take it to an accredited drive shaft repair shop or take the vehicle to an accredited drive line specialist shop
the repair will require that you place the flange back on the shaft after the bearing replacement in exactly the right position or you will get harmonic vibration after the job so talk with the experts first if you want to diy

May 09, 2017 | Gateway Cars & Trucks

1 Answer

My 1989 Chevy Silverado 2500 vibrating when running, it is worse when driving


Would check first your ubolts and carrier bearring, , See if you have any slack in your driveshaft by turning side to side if so you need a set of ubolts, and check your carrier bearing by pushing up and down on driveshaft, if so needs replaced. good luck to you.

Mar 28, 2011 | Chevrolet Silverado 2500 Cars & Trucks

1 Answer

I have a 2007 Lincoln MKZ with the infamous driveshaft carrier bearing noise. My question is can the (front) carrier bearing be replaced alone instead of the complete driveshaft at a tune of 700 +...


First, I wouldn't be at a dealer

I mark all my drive shafts, as installed, and take
them to a driveshaft shop that,makes or repairs them

I have ALL driveshafts balanced

I have a Lincoln LS ,so I'm guessing your
newer MKZ is front wheel drive ??

Having once owned a trans repair shop, your
transaxle ,if that is what you have, will have to
be stripped clean, to do the bearings your talking
about

On a rear drive, such as my LS, you still have to
remove the rear differental case and strip it, for
brgs

The $700 sounds like a dealer fishing for a solution
to a rear wheel drive vehicle with a vibration

They try a new drive shaft,why not,only your money

Mar 26, 2011 | Lincoln MKZ Cars & Trucks

2 Answers

2005 ford escape 3.0L AWD XLT - DRIVESHAFT CARRIER BEARING BAD - CAN IT BE REPLACED OR MUST I CHANGE THE DRIVESHAFT FRONT AND REAR?


if there is some one in your area that balances driveshafts they can change just the bearing for you

Nov 10, 2009 | 2004 Ford Escape

Not finding what you are looking for?
1992 Chevrolet K1500 Logo

Related Topics:

423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...