Question about Chevrolet Silverado 1500

1 Answer

The service 4x4 light is on and it will not shift inyo 4x4.it has push button 4wd.has power to the push buttons but will not go into 4wd.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Hello, there are many things that can cause this, the most common problem is the encoder sensor inside the encoder motor on the side of transfer case. this is what actaully shifts the transfer case in 4wd. there are several software updates for the 4wd system on this truck also. this requires a gm scan tool and aprogramming station to install the software updates. you will need to start by having the 4wd system scanned for trouble codes. once a code has been pulled from the syste, then we would have a much better idea what the fault is. I suspect that there is a code C0327 stored in the system

Posted on Nov 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not shift into 4x4 drive


The Front Axle Actuator is probably your problem. I have replaced my Actuator TWICE in the last 7 years.... The Reason for the Service 4WD was the Failed Attempt. If you are able to test the Power going to the Actuator and there is none, then you have one of 3 switches that went bad but Chevrolet/GM is known for having the Defective Actuators. Aftermarket Actuators are available.
f25b3488-08ed-419b-acd4-38bcd0197eee.jpg

Mar 03, 2014 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

How to put into 4x4 hi ?


If its a 4WD there is either a push button on the dash left side of steering colomn, its marked 4hi. If manual shifter in on floor center console. Pull back on lever to second notch marker 4hi. If you are in 4lo now and can't get out. first put tranny shifter in neutral while engine running, then shift transfer case into neutral (manual push forward), push button hold 4hi and 4lo at the same time til "N" green light comes on. Then shift either into 4hi.

Jan 27, 2011 | 2001 GMC Yukon

2 Answers

Front end will not lock in in 4x4 transfer case is in & dash lite shows 4x4 but front wheels don;t lock in


Ok, this is probably going to sound greek if you have no automotive experiance, so here goes:

There are 2 possibilities I can think of at the moment depending on your 4wd system, however there are several things that can cause this

If you have a Push button 4wd (you push a button or turn a knob) the system engages using actuators or sylinoids meening you turn the 4wd on, the switch sends power to the selector option (high and low) and the 4wd light on the dash. the selector determines where the actuator/silenoid engages (either high or low) in the transfer case. However the actuator or silenoid can be faulty and yet the system will say 4wd is on because the switches still sending power to the 4x4 light

The next setup is the manual linkage set up, and given the year of your kia I doubt you have this setup However I am going to go through it anyway.

With a maual linkage setup you engage the trasfer case maualy using the 4wd shifter. Ironically on newer manual shift 4wd systems the dash light is still triggered electrically by location of the shifter not what is going on in the transfer case (Ah a flaw in the design) So if you linkage is loose/bent/damaged or somehow disconnected your 4wd wont engage but the light will still show that it is! Hope this helps

Jan 30, 2010 | 1999 Kia Sportage

3 Answers

4wd how to enguage


make sure your in nutural, or park then if you have hub locks turn them to locking position. then shift small shifter if available into 4 wheel low or high. or may have just a push button to engauge. then shift into low or high. then you may use your regular stick to shift or just shift into drive w automatic.

Jan 27, 2010 | 1998 Isuzu Rodeo

1 Answer

No 4wd


Most likely,it's the 4x4 shift motor on the transfer case,they get water/dirt/ inside.Check all fuses and connector to 4x4 shift motor.Sometimes you can find a used one,but not too often.

Oct 06, 2009 | 1991 Ford Explorer

1 Answer

Got 93 ford explorer have 4x4 push button type 4


There is a Shift motor that shifts it in 4wheel drive and also a shift mudule I believe on this year. Either one of these can be bad.

Aug 01, 2009 | Ford Explorer Cars & Trucks

1 Answer

My truck is stuck in 4LO and the button in the truck dont work.


If its a push button 4x4 take it to the shop its a VERY COMMON Problem dealing with the electric.Once you pay the $400 to get it fixed get rid of the truck and settle for a Jimmy/Blazer/Bravada with a floor shift 4x4..GM had problems with the push button 4x4.DONT DRIVE YOUR TRUCK IN THE MEANTIME.YOU WILL BLOW YOUR TRANSFER CASE RIGHT OUT OF IT!

May 20, 2009 | 1998 GMC Jimmy

1 Answer

Ford 2005 4x4 problem.


2-Speed Torque-On-Demand (TOD) Operation
The automatic 4-wheel drive (A4WD) system is a 2-speed torque-on-demand (TOD) operation that utilizes the following components:
  • Transfer case
  • 4-wheel drive (4WD) control module (integral to the powertrain control module [PCM])
  • Mode select switch (MSS)
  • Gearmotor encoder assembly (part of the transfer case shift motor)
  • Transfer case shift motor
  • Shift motor sense plate (part of the gearmotor encoder assembly)
Principles of Operation
Transfer Case Shift Motor The externally mounted transfer case shift motor, located at the rear of the transfer case, turns the shift cam assembly. As the shift cam assembly turns, it positions the reduction shift fork for desired transfer case operation. An integral position sensor in the shift motor provides shift motor position information to the 4WD control module.
Mode Select Switch (MSS) The push button MSS, mounted on the instrument panel, allows the operator to select the 4x4 Auto, 4x4 High, and 4x4 Low transfer case operating modes. The indicator light, on the instrument cluster push button, will illuminate only when the 4x4 Low position is engaged.
Visual Inspection Chart Mechanical Electrical
  • Axle shafts and CV joints
  • Driveshaft and universal joints
  • Fluid leaks
  • Matching tire sizes
  • Transfer case shift motor
  • Battery junction box (BJB) fuses:
    • 8 (30A)
    • 17 (5A)
    • 18 (20A)
  • Central junction box (CJB) fuses:
    • 12 (5A)
    • 24 (15A)
  • 4x4 module (PCM)
  • Wiring harness
  • Gearmotor encoder contact plate
  • Connector(s)
  • Circuitry
  • Mode indication switch (MSS)

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the concern is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • CAN circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for 4WD module (PCM), Go To Pinpoint Test G .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out the 4WD module (PCM) self test.
  1. If the DTCs retrieved are related to the concern, go to the 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics. 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index
    DTC Description Source Action B1317 Battery Voltage HIGH 4WD Module (PCM) REFER to Section 414-00 . B1318 Battery Voltage LOW 4WD Module (PCM) REFER to Section 414-00 . B1319 Driver Door Ajar Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1322 Driver Door Ajar Circuit Short To Ground 4WD Module (PCM) Go To Pinpoint Test M . B1342 ECU is Defective 4WD Module (PCM) CLEAR the DTCs. REPEAT the 4x4 module (PCM) self test. If DTC B1342 is retrieved, INSTALL a new 4x4 module (PCM). REFER to Section 303-14 . CLEAR the DTCs. REPEAT the self test. B1483 Brake Pedal Input Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1485 Brake Pedal Input Short to Battery 4WD Module (PCM) Go To Pinpoint Test M . C1729 Transfer Case Unable to Transition Between 4H and 4L 4WD Module (PCM) Go To Pinpoint Test K . C1970 4WD Low Mode Switch LED Short to Battery 4WD Module (PCM) Go To Pinpoint Test K . C1971 4WD Low Mode Switch LED Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1707 Transfer Case NEUTRAL or PARK/NEUTRAL Indication Circuit 4WD Module (PCM) Go To Pinpoint Test M . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1816 Transmission NEUTRAL Safety Switch Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . P1819 Transmission NEUTRAL Safety Switch Circuit Short to Ground 4WD Module (PCM) Go To Pinpoint Test M . P1820 Transfer Case Clockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1822 Transfer Case Clockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1824 4-Wheel Drive Clutch Relay Circuit Failure 4WD Module (PCM) Go To Pinpoint Test H . P1826 4-Wheel Drive Low Clutch Relay Short Circuit to Battery 4WD Module (PCM) Go To Pinpoint Test H . P1827 4-Wheel Drive Low Clutch Relay Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test H . P1828 Transfer Case Counterclockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1830 Transfer Case Counterclockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1849 Transfer Case Contact Plate A Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1853 Transfer Case Contact Plate B Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1857 Transfer Case Contact Plate C Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1861 Transfer Case Contact Plate D Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1867 Transfer Case Contact Plate General Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1891 Transfer Case Contact Plate Ground Return Open Circuit 4WD Module (PCM) Go To Pinpoint Test K . U1900 CAN Communication BUS Fault 4WD Module (PCM) REFER to Section 418-00 . U2023 External Node Fault 4WD Module (PCM) REFER to Section 418-00 . U2051 One Or More Calibration Files Missing/Corrupt 4WD Module (PCM) Reprogram/Reflash the 4x4 module. REFER to Section 418-00 . - For All Other DTCs 4WD Module (PCM) REFER to Section 418-00 .
  2. Your best bet mite be to take it to a qualified repair shop !

May 30, 2017 | 2005 Ford Explorer

3 Answers

Transfer case motor for push button 4x4


i have a 1993 blazer 4.3 w code 4x4 with a 4L60 E . my truck wouldn;t go in 4 hi or low. so i changed the transfer case motor and it works fine now. If you turn the ignition key to on but not crank the engine and open the driver door and push 4 hi button, you should hear the transfer case motor cycle for 3 or 4 seconds every time you push button and the light will flash until it goes in 4wd If the 4 hi button light doesn't flash during cycle then it could be a bad switch. if the transfer case motor won't cycle it could be a fuse or a bad transfer case motor . Hope this answers your question.
pgale89

Dec 16, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...