Question about 2006 Toyota RAV4

1 Answer

Access to right side backup lamp wires

How do I remove the inside trim and the jack storage to provide access to the right side backup lamp wires? I want to wire in a backup camera.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 330 Answers

  1. Usually the trim has several clamps behind the trim to connect to the body, use screw driver pup it up slowly.
  2. Maybe you need to take off the ceiling panel,
  3. Take the panel off, usually have several screws behind the handles, seat belt mount bars, pup the small plastic cover up on those bars and you will see the screws.
  4. step by step install you unit.
  5. Hope this can help. good luck

Posted on Jul 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reverse lights stay on in drive 2004 buick rendezvous cxl


Backup Lamps
The TURN SIG fuse in the console fuse block supplies battery positive voltage to park neutral position switch. When the gear selector lever is in the REVERSE position, power is supplied to both of the backup lamps. The backup lamps are grounded at G401 and G402.
Do you know what DTC'S - diagnostic trouble codes are ?
DTC B2552
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamp relay control circuit energizing the backup lamp relay. The BCM connects directly to the center console fuse block with no external wiring between them.
DTC B2553
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamps relay control circuit energizing the backup lamp relay. The BCM connects directly to the center console fuse block with no external wiring between them.
Backup Lamps Always On
  1. Turn ON the ignition.
  2. Shift the gear selector lever to the REVERSE position and then to the PARK position.
Do the backup lamps turn on in REVERSE and turn off in PARK?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

Remove the backup lamps relay.
Do the backup lamps turn OFF?
Go to Step 5
Go to Step 4

4

Repair a short in the backup lamps relay switched battery positive voltage supply circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Check the back-up lamps relay #45 in the center console fuse/relay box .
Fuse Block - Center Console
Inside of console, behind the right console access panel

Check

Jun 11, 2016 | 2004 Buick Rendezvous

2 Answers

2006 Pontiac grand prix where is the blend door actuator mode at




  1. Remove the right instrument panel (I/P) insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gages, and Console.


  2. Remove the I/P compartment. Refer to Instrument Panel Compartment Replacement in Instrument Panel, Gages, and Console.

    alt="Object Number: 1194925 Size: SH">



  3. alt="Click here for detailed picture of above image.">


  4. Remove the screws that secure the mode actuator (1) to the HVAC module assembly.


  5. Remove the mode actuator from the HVAC module assembly.


  6. Disconnect the electrical connector from the mode actuator.



a+2saweek5chaaaaaelftksuqmcc



Instrument Panel Insulator Panel Replacement - Right Side



Remove 3 fasteners. Rotate the lamp. Remove the lamp from the insulator. Remove the insulator.



Instrument Panel Compartment Replacement



Using the finger opening, remove the access hole cover from the right instrument panel (I/P) compartment



Pull the I/P outboard trim plate rearward in order to release the retainers. Remove the I/P trim plate. Open the I/P compartment



Disengage the compartment door stop using the following procedure:







5.1.





Press the upper door stop (2) toward the center of the vehicle.














5.2.





Rotate the door away from the compartment.








Pull the I/P accessory trim plate rearward slightly for access to the I/P inboard trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .

alt="Object Number: 929399 Size: SH">

Jan 12, 2016 | Pontiac Cars & Trucks

2 Answers

Bentley Boot lid manual release


This is all the Bentley shows:

doorlockswitch1.gif
Location: Driver's side door trim in storage compartment.

Removing:

- Remove driver's side door trim:
Repair Manual, Body Interior, Repair Group 70 - Unplug connectors.


doorlockswitch2.gif
Carefully disengage catches -arrows-.
- Press switch for interior monitoring and towing protection -1- or trunk release switch -2- out of trim toward rear.

Installing

Installation is carried out in the reverse order.


doorlockswitch3.gif
Remove trunk lid lock.

Repair Manual, Body Exterior, Repair Group 55
- Use a flat screwdriver to pry plastic tab -3- off retaining pins -1-.
- Bend plastic tab fully to rear.
- Pull contact switch -2- first sideways and then up and out of trunk lid lock.

Installing

Install in reverse order, paying attention to the following:

Note:

Make sure that washers are correctly seated between plastic tab and trunk lid lock.

Sep 01, 2012 | Bentley Continental Flying Spur Cars &...

1 Answer

Where is the flasher relay on a 2002 monte carlo


It's part of the hazard switch. have to take trim panel off to replace it .Apply the parking brake.
If the vehicle is equipped with a column shift, position the transaxle shift control indicator to 1.
Adjust the steering wheel for access.
Using a small, flat-bladed tool, gently remove the bezel from the ignition lock cylinder.
For the Impala, remove the right and the left access covers from the instrument panel (IP) fuse block.
For the Monte Carlo, remove the left access cover from the IP fuse block.
Remove the steering column filler. Refer to Steering Column Opening Filler Replacement .
For the Monte Carlo, open the instrument panel compartment door.
Remove the trim plate screws from the IP cluster.
Start at the left side of the IP cluster trim plate. Grasp the trim plate and carefully pull rearward. Disengage the IP cluster trim plate in order to easily access the hazard warning switch
Disconnect the electrical connectors from the hazard warning switch.
Remove the hazard warning switch from the IP cluster trim plate.


13710300-sqgggmolzf4u4c55ip0gdkvq-5-0.jpg It's probably the switch on the steering column ! An not the flasher but you never know without testing .
Turn Signal Lamps and/or Indicators Inoperative
Step
Action
Yes
No
Schematic Reference: Exterior Lights Schematics
1
Did you perform the Lighting System Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Lighting Systems
2
Turn the ignition to the ON position.
Place the turn signal switch to a turn left or a turn right position.
Do the turn signal tamps flash ON and OFF?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3
3
Disconnect the hazard switch.
Connect a test lamp between the TURN SIGNAL Fuse battery positive voltage circuit and ground.
Does the test lamp illuminate?
Go to Step 4
Go to Step 7
4
Reconnect the hazard switch.
At C201, connect a test lamp between the turn signal flasher supply circuit and ground.
Does the test lamp flash ON and OFF?
Go to Step 5
Go to Step 6
5
At C201, connect a test lamp between the turn signal flasher supply circuit of the hazard switch and inoperative turn signal lamps supply voltage circuit.
Does the test lamp flash ON and OFF?
Go to Step 9
Go to Step 8
6
Test for a high resistance or an open in the turn signal flasher supply circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10
7
Repair a high resistance or an open in the TURN SIGNAL Fuse battery positive voltage circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 11
--
8
Repair a high resistance or an open in the turn signal lamps supply voltage circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 11
--
9
Replace the turn signal switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 11
--
10
Replace the hazard switch. Refer to Hazard Warning Switch Replacement in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 11
--
11
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jul 21, 2012 | 2002 Chevrolet Monte Carlo

1 Answer

I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Feb 02, 2012 | 2000 Dodge Caravan

1 Answer

Replace a brake light


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif

Nov 04, 2010 | 1998 Saturn SL

1 Answer

I need to replace rear tail light bulbs on 1996 Saturn SL1


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Reverse Light EXCEPT 1991-96 COUPE For the Saturn wagons and sedans, the reverse lamp is part of the rear turn signal, brake and parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. 1991-96 COUPE
  1. Disconnect the negative battery cable.
  2. Reach behind the bumper bar and disconnect the harness and socket from the reverse lamp. Remove the bulb from the socket.
  3. If necessary, unfasten the retaining nuts and remove the lamp from the bumper bar.
  4. Installation is the reverse of the removal. Fig. 14: Exploded view of the reverse lamp mounting - 1991-96 coupe 84196118.gif

Oct 23, 2010 | 1996 Saturn SL

1 Answer

I need to remove 2004 toyota sequoia tailgate door panel to get access the rear tail light to install a backup camera. I don't see any obvious removal points.


Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Sep 20, 2009 | 2003 Toyota Sequoia

1 Answer

How do you replace reverse bulb on 2001 deville?


2001 Cadillac DeVille V8-4.6L VIN 9
BACKUP LAMP REPLACEMENT
REMOVAL PROCEDURE
1. Pull down the rear compartment lid trim. Refer to Compartment Lid Trim Replacement - Rear in Trunk/Liftgate.
2. Disconnect the electrical connector.
3. Remove the fasteners that secure the backup lamp assembly.
4. Remove the backup lamp assembly.
5. Remove the bulb assembly.
6. Remove the bulb.
INSTALLATION PROCEDURE
1. Install the bulb into the bulb socket.
2. Install the bulb assembly into the backup lamp assembly.
3. Pull the wire harness through the body and seat the grommet.
4. Install the backup lamp assembly to the rear compartment lid.
NOTE: Refer to Fastener Notice in Service Precautions.
5. Install the fasteners in order to secure the backup lamp assembly.
Tighten
Tighten the fasteners to 4.5 N.m (40 lb in).
6. Connect the electrical connector.
7. Install the rear compartment lid trim.

Sep 11, 2009 | Cadillac DeVille Cars & Trucks

1 Answer

Need to replace right brake light. How do I remove and replace trunk lining to get access withou doing damage to the liner? What is the correct lamp?


Remove the luggage compartment rear trim panel. Detach luggage compartment side trim panel. Detach the rear lamp assembly bulb holder. Remove the rear lamp assembly. To install, reverse the removal procedure.

Aug 03, 2009 | 2003 Jaguar S-Type

Not finding what you are looking for?
2006 Toyota RAV4 Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...