Question about 1994 Jeep Grand Cherokee

1 Answer

It dies when u put it in gear the only way it wont is to put it in netural when ur sitting still,

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Bad torque converter.
Basically needs a transmission rebuild to fix it properly.

Posted on Nov 06, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

'99 dodge grand caravan it won't shift above first gear, the speedometer won't work, also dies when put in netural while driving???

Replace the out put speed sensor. The reason it is in 2nd gear.(limp mode) Looking down at the front of the transmission, it is the sensor on the right. The dieing could be a dirty air filter, throttle body and IAC motor.

Dec 26, 2015 | Dodge Cars & Trucks

1 Answer

Have a 1989 pontiac grand prix 3.1, that runs like crap when warmed up. Pops n cracks, dies. & re-starts on its own. It will die when ur sitting there in gear with foot on gas n other foot on brake....

From what you are saying this problem is when you have your foot on the brake. If that is the case remove and blank of the brake booster vacuum hose and see if the problem persists. If not then the fault will be in the brake booster allowing air into the manifold and up setting the air/fuel mixture and running too lean

Jul 20, 2014 | 1989 Pontiac Grand Prix

1 Answer

Truck wont shift into gear I will put it into netural then drive after starting

I had similar situation- cam wore loose for indicator. Put it in park, but the cam was so loose it failed to drop in properly. End result is the truck thought it was in R, and vehicle wont start that way. I ended up tearing into column and replacing cables, cam, and multi-function all at once.

Jul 10, 2014 | 1998 Chevrolet Chevrolet silverado

1 Answer

Truckwill not shift out of 1gear sometimes without letting off gas if this doesnt work then i can put in netural and back in drive and it will work

Sounds as if the spider gears are going bad. There are bands or belts in your tranny for each gear. They may be going bad. Have you checked the transmission fluid level? This also could be the most obvious reason. Just
Low fluid level? Noticed any drips in the driveway ?

Mar 09, 2013 | 1999 Dodge Ram

1 Answer

Gear shift slides up and down but wont go into gear.

sounds like the linkage cable frayed and broke. hope you get it fixed.

Oct 24, 2012 | 2005 Buick Rendezvous

1 Answer

Car wont start

if ur cars is on petrol than go for the injector cleaning spark plug leaning and chk the fuel pump module.if it is diesel than only chk the fuel pump

Jun 16, 2012 | 1998 Audi A8

1 Answer

I have a 94 achieva i got it from my sister, it will run a few days of so then while driving it will start cutting out and the gauges will start going up and down and then it will die. some times it will...

as as far as the dying as soon as u put in gear and easy trick that usually helps those is to unplug the the harness that goes to the transmission cause these cars when the torque control solenoid fails it wont unlock and on ur car thats the only thing electronic is the torque convertor

Jun 12, 2011 | 1994 Oldsmobile Achieva Special Edition

1 Answer

I want to know how do use the 4x4 beause i dont know how to use it

Hi, if your 4x4 is push button control just put in netural and push the button ,low range is real low gear for like mud digging and off roading and high range is for like the road like when its snow on road. If you have the shifter type put in netural and do the same as above just select 4 high or 4 low after placed in gear put your car in drive . That is how your 4x4 works. If i can help just re post.

Jan 09, 2011 | 2002 Ford Explorer

1 Answer

Fuel issue

Any dtc's? Check fuel pressure and ignition spark...

Oct 18, 2008 | 1995 Buick Century

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides