Question about 1993 Jeep Grand Cherokee

1 Answer

My neutral safety switch is acting up. how do i find the neutral safety switch?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Your N/S/S is on the passenger side of the transmission directly opposite from where the linkage on the drivers side connects (it's on the same shaft). It is usually corroded onto the shaft and you will need to use lots of wd40 or other solvent and some patience in getting it free. It's plastic and if you pry hard you will break it. The harness is connected up on the firewall near the dipstick tube. Instructions for removal can be found in chiltons or haynes manuals. The switch itself is over $200 new so you may want to find one in a scrapyard or if you are careful (there are small contacts inside with springs) you can take it apart and clean it up.

Posted on Nov 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Netural safety switch


Daewoo cars have track record for dependability in addition to solid construction. The most important part of a car's design is the safety features. Circumvent excessive risk while motoring by insuring that your car has the safety gear that you want. A vehicle's Neutral Safety Switch is located on your clutch in the case that it's a manual transmission, and on the shifter in an automatic. A broken Neutral Safety Switch can cause your vehicle to suddenly start in gear, causing vehicle damage or personal injury.

If you don't have the Neutral Safety Switch, your vehicle will fail to work. The Neutral Safety Switch is typically situated below the clutch of trucks which have a stick-shift transmission. The primary function of a Neutral Safety Switch is to stop your truck from starting when in gear. The car's Neutral Safety Switch acts as a safety feature, keeping you from starting the engine if the car is in gear. The Neutral Safety Switch is an electronic part which is essential while starting your car.Here's a link to what it look's like.

Mar 22, 2013 | 2000 Daewoo Lanos

2 Answers

Truck will not start in park, only neutral. Is there a sensor that could cause that


depending on the year, some models have a switch on the base of the steering column if the shifter is up there..and on rthe shifter linkage on the transmission itself for the floor type..sometimes it can be adjusted on the mount but if its acting up..replace it.. good luck..

Jan 20, 2013 | Cars & Trucks

1 Answer

Where is the neutral safety switch?


This van has a PRNDL switch,mounted on the trans(it tells the PCM what gear you're in,also acts as neutral switch for the starter,and operates the back up lights)

Jan 02, 2012 | 1998 Plymouth Grand Voyager

1 Answer

Need location of neutral safty switch on my 1990 cadilac broughm 350 engin e


The neutral safety switch is located on the top and toward the base of the steering column almost to the floorboard.

To remove or install the neutral safety switch be sure to place the shifter in the neutral position, then dis-connect the wire connector at the neutral safety switch, then remove the securing screws and then remove the neutral safety switch.

Install the new neutral safety switch and do not over-tighten the securing screws, then remove the alignment pin and re-connect the wire connector to the neutral safety switch. (be sure not to remove the alignment pin until the neutral safety switch has been installed)

Check to be certain that the vehicle only starts in "Park" or "Neutral". Here is an image to help assist you, and let me know if you require any further assistance.


f494426.jpg

Sep 12, 2010 | Cadillac Brougham Cars & Trucks

1 Answer

2002 chevy silverado 4wd will not start acts like it is in drive does not know that it is in park


that could be a bad, loose or misadjusted "neutral safety switch" .. in some the brake has to be applied before starting .. that would involve a brake safety switch ..

Feb 27, 2010 | 2002 Chevrolet Silverado 1500HD

2 Answers

Where is Neutral safty sensor switch located on Grand Cherokee


OK then the switch is part of the gear selector switch on the side of the trans where the shift linkage hooks up. here is a picture and part number.
ACDELCO Part # C2241 $233.89

673ffc9.jpg

Feb 17, 2009 | 1996 Jeep Cherokee Country

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...