Question about Isuzu Rodeo

Open Question

Which way around does the clutch plate for 97 holden rodeo go, is it raised portion facing flywheel or facing pressure plate

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stevenhurc
  • 450 Answers

SOURCE: NEW CLUTCH SLIPPING ON 2004 V6 HOLDEN RODEO

did you bleed the hydralic clutch system on this vehicle? = air in system or not bleed properly.
most of the flywheels for this model were not to be machined...... however it is ok to machine these only slightly but you must machine the surface the clutch plate contacts with the same amount as the outer raised section the pressure plate bolts to.
new flywheels have painted stamped writing saying do not machine...so if hydralic system is ok find out about flywheel.
also may pay to check clamping force of pressure plate most clutch places can do this or some workshops that is if fingers on pressure plate are all at the same height, not broken or cracked..

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which side of the clutch plate faces the crankshaft side?


hold the clutch plate against the flywheel and try to rotate
if it is wrong the hub section will hit on the flywheel bolt heads

practice dictates that the raised section ( bit with the springs in the housing of the clutch plate) faces the gear box so that there is clearance to those springs to the flywheel bolt heads
besides that if you have a new clutch plate if will have " this side to the flywheel" printed on it

Oct 28, 2016 | Cars & Trucks

1 Answer

Clutch installation


Genewrally speaking you need to remove the gear box. UNdo the bolts holding the clutch pressure plate on the flywheel. . Do this by undoing each bolt a few turns at a time. Remove pressure plate and clutch plate. Clean flywheel face. Remove bearing at center of crankshaft and replace as it will be dry and probably rusty. Fit new clutch plate taking care to observe the correct way the plate is fitted. Normally the raised hub section faces away from the flywheel. THis can be checked by pressing the plate against the flywheel and turning it and it it hits the crank bolts you have it in the wrong way round. Fit the pressure plate over the plate and insert the bolts. Some units have 2 or 4 bolts longer than the restand this is to allow the plate to be depressed a fraction to allow the other bolts to screw in. Place a clutch aligning tool through the clutch plate and into the bearing. Evenly retension the pressure plate bolts going alternately across the cover a bit at a time . When retensioned remove the clutch aligning tool. Remove and replace the throw out bearing on the clutch release forks. Ensure that the clutch kit is all new as mixing parts will not work. Refit the gear box. Basically that is the proceedure but to be exact get the manual for your vehicle to cover any extra steps needed for that vehicle.

Mar 07, 2013 | Ford Transit Connect Cars & Trucks

1 Answer

I am fitting a new clutch assy to my vy ss ute, i bought the kit genuine from Holden removed the old assy and fitted the new flywheel,clutch plate n pressure plate. but my problem is that i have torqued...


did you use a pilot spline to align the clutch and did you change the pilot bearing in the end of the crank. The clutch plate maybe interfering with the pressure plate if it is not lined up.

May 06, 2017 | Cars & Trucks

2 Answers

New clutch still slipping


Lets start with what was replaced : Clutch pressure plate, throwout bearing,pilot bearing,input shaft bearing, was flywheel cut or replaced,Clutch cable or slave cylinder (whatever is applicable,) Lets see what repair shop says. Depending on what they say they did or didn't do we will take it from there.
keep me posted

Apr 27, 2010 | 1992 Isuzu Rodeo

1 Answer

I HAVE A 1999 SATURN SL PUT NEW CLUTCH IN AND A NEW PREBLEED CLUTCH MASTER CYLINDER AND SLAVE CYLINDER,HAVE GOOD CLUTCH PRESSURE WHEN PUSHING DOWN PEDAL BUT CLUTCH IS NOT ENGAGING. ANY IDEAS?


Are you certain you or your mechanic installed the clutch plate facing the right direction? It is usually marked on one side to tell you which way to face it. I have personally done this and had the same issue, if the hub portion of the plate is rubbing on the flywheel it won't kick out or in all the way, and if left it can cause damage to the flywheel.

Good luck.

Are you certain you or your mechanic installed the clutch plate facing the right direction? It is usually marked on one side to tell you which way to face it. I have personally done this and had the same issue, if the hub portion of the plate is rubbing on the flywheel it won't kick out or in all the way, and if left it can cause damage to the flywheel.

Good luck.

Apr 04, 2010 | 1996 Saturn SC

1 Answer

NEW CLUTCH SLIPPING ON 2004 V6 HOLDEN RODEO


did you bleed the hydralic clutch system on this vehicle? = air in system or not bleed properly.
most of the flywheels for this model were not to be machined...... however it is ok to machine these only slightly but you must machine the surface the clutch plate contacts with the same amount as the outer raised section the pressure plate bolts to.
new flywheels have painted stamped writing saying do not machine...so if hydralic system is ok find out about flywheel.
also may pay to check clamping force of pressure plate most clutch places can do this or some workshops that is if fingers on pressure plate are all at the same height, not broken or cracked..

Dec 01, 2009 | 2004 Isuzu Rodeo

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

1 Answer

Clutch on renault megane 1.4 98


the raised side faces the gearbox side

May 31, 2008 | 2003 Renault 181

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...