Question about 2007 Toyota Camry

1 Answer

I need step by step procedure for rear brake stallation

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 835 Answers

My suggestion if you have never done rear brakes is to buy a manual for the vehicle

Posted on Nov 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 01 GMC Jimmy 4.3L 4WD & we are trying to bleed the brakes but the scanner says my vehicle is going 3MPH so we manually bleed the brakes but the pedals still easily is pushed to the floor.


Bad master cylinder . What are you using a scan tool for ? No need Unless your Installing a new Electro-Hydraulic Control Unit (EHCU) or new Brake Pressure Modulator Valve (BPMV).
Hydraulic Brake System Bleeding (Manual)
Caution: Refer to Brake Fluid Irritant Caution in the Preface section.
Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.
Place a clean shop cloth beneath the brake master cylinder to prevent brake fluid spills.
With the ignition OFF and the brakes cool, apply the brakes 3-5 times, or until the brake pedal effort increases significantly, in order to deplete the brake booster power reserve.
If you have performed a brake master cylinder bench bleeding on this vehicle, or if you disconnected the brake pipes from the master cylinder, you must perform the following steps:
3.1. Ensure that the brake master cylinder reservoir is full to the maximum-fill level. If necessary add GM approved brake fluid from a clean, sealed brake fluid container. Refer to Fluid and Lubricant Recommendations.
If removal of the reservoir cap and diaphragm is necessary, clean the outside of the reservoir on and around the cap prior to removal.
3.2. With the rear brake pipe installed securely to the master cylinder, loosen and separate the front brake pipe from the front port of the brake master cylinder.
3.3. Allow a small amount of brake fluid to gravity bleed from the open port of the master cylinder.
3.4. Reconnect the brake pipe to the master cylinder port and tighten securely.
3.5. Have an assistant slowly depress the brake pedal fully and maintain steady pressure on the pedal.
3.6. Loosen the same brake pipe to purge air from the open port of the master cylinder.
3.7. Tighten the brake pipe, then have the assistant slowly release the brake pedal.
3.8. Wait 15 seconds, then repeat steps 3.3-3.7 until all air is purged from the same port of the master cylinder.
3.9. With the front brake pipe installed securely to the master cylinder, after all air has been purged from the front port of the master cylinder, loosen and separate the rear brake pipe from the master cylinder, then repeat steps 3.3-3.8.
3.10. After completing the final master cylinder port bleeding procedure, ensure that both of the brake pipe-to-master cylinder fittings are properly tightened.
Fill the brake master cylinder reservoir with GM approved brake fluid from a clean, sealed brake fluid container. Ensure that the brake master cylinder reservoir remains at least half-full during this bleeding procedure. Add fluid as needed to maintain the proper level.
Clean the outside of the reservoir on and around the reservoir cap prior to removing the cap and diaphragm.
Install a proper box-end wrench onto the RIGHT REAR wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve.
Submerge the open end of the transparent hose into a transparent container partially filled with GM approved brake fluid from a clean, sealed brake fluid container.
Have an assistant slowly depress the brake pedal fully and maintain steady pressure on the pedal.
Loosen the bleeder valve to purge air from the wheel hydraulic circuit.
Tighten the bleeder valve, then have the assistant slowly release the brake pedal.
Wait 15 seconds, then repeat steps 8-10 until all air is purged from the same wheel hydraulic circuit.
With the right rear wheel hydraulic circuit bleeder valve tightened securely, after all air has been purged from the right rear hydraulic circuit install a proper box-end wrench onto the LEFT REAR wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
With the left rear wheel hydraulic circuit bleeder valve tightened securely, after all air purged from the left rear hydraulic circuit, install a proper box-end wrench onto the RIGHT FRONT wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
With the right front wheel hydraulic circuit bleeder valve tightened securely, after all air has been purged from the right front hydraulic circuit, install a proper box-end wrench onto the LEFT FRONT wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
After completing the final wheel hydraulic circuit bleeding procedure, ensure that each of the 4 wheel hydraulic circuit bleeder valves are properly tightened.
Fill the brake master cylinder reservoir to the maximum-fill level with GM approved brake fluid from a clean, sealed brake fluid container.
Slowly depress and release the brake pedal. Observe the feel of the brake pedal.
If the brake pedal feels spongy, repeat the bleeding procedure again. If the brake pedal still feels spongy after repeating the bleeding procedure, perform the following steps:
21.1. Inspect the brake system for external leaks. Refer to Brake System External Leak Inspection.
21.2. Pressure bleed the hydraulic brake system in order to purge any air that may still be trapped in the system.
Turn the ignition key ON, with the engine OFF. Check to see if the brake system warning lamp remains illuminated.
Important: If the brake system warning lamp remains illuminated, DO NOT allow the vehicle to be driven until it is diagnosed and repaired.
If the brake system warning lamp remains illuminated, refer to Symptoms - Hydraulic Brakes

Feb 26, 2017 | GMC Cars & Trucks

1 Answer

How to replace a rear brake cylinder and new brake shoes?


remove rear wheel , pull off the brake drum , you may have to use two flat blade screwdrivers one eachside to prize the drum off,clamp the flexable brake hose behind the brake assembly so fluid does'nt drainout,at the rear of the back plate you will need to disssconnect the hand brake cable usually a spring needs compressing by hand and then are able to disconnect the cable from its seating,take a picture of the brake shoe assembly before dismantling it so you know where the components go when re building, there will be spring loaded pin holding the shoes in place ,with a pair of pliers push and twist the flat washer so the pin head comes through the retaining washer you should then be able to lift away the shoe's and mechanism , next at the rear of the cylinder disconnect the brake pipe and the two retaining screws , fittings is the reverse , if you can get a workshop manual for the vehicle this will give step by step guide a tips for that exact vehicle, once back to gether unclamp the brake hose and bleed the brakes , take your time and if not sure if it looks right have a look at the picture or alternatively take the other wheel and drum off to check good luck

Sep 25, 2014 | Cars & Trucks

1 Answer

1990 jeep wrangler bleeding breaks


Hi there:
I suggest to check this procedure, when the hydraulic brake system must be bled whenever a fluid line has been disconnected because air gets into the system.

A leak in the system may sometimes be indicated by a spongy brake pedal. Air trapped in the system is compressible and does not permit the pressure applied to the brake pedal to be transmitted solidly through the brakes. The system must be absolutely free from air at all times. If the master cylinder has been overhauled or a new cylinder has been installed, bleed the cylinder on a bench before installation. When bleeding brakes, bleed at the wheel most distant from the master cylinder first, the next most distant second, and so on. During the bleeding operation the master cylinder must be kept at least 3 / 4 full of brake fluid.


The ABS bleeding procedure is different from the conventional method. It consists of the following three steps:
Step 1: Conventional manual brake bleed.
Step 2: Bleeding the system using the DRB scan tool.
Step 3: An additional conventional manual brake bleed.

The recommended ABS bleeding procedure is as follows:
  1. To bleed the brakes, first carefully clean all dirt from around the master cylinder filler cap. Remove the filler cap and fill the master cylinder with DOT 3 brake fluid to the lower edge of the filler neck.
  2. Bleed the master cylinder first. Have a helper operate the brake pedal while bleeding each master cylinder fluid outlet line. Do not allow the master cylinder to to run out of fluid,as this will allow additional air to be drawn into the cylinder.
  3. Bleed the brake system in the following sequence:
    1. Master cylinder
    2. HCU valve body (at fluid lines)
    3. Right rear wheel
    4. Left rear wheel
    5. Right front wheel
    6. Left front wheel
  4. Clean off the bleeder connections at all four wheel cylinders. Attach the bleeder hose to the right rear wheel cylinder bleeder screw and place the end of the tube in a glass jar, submerged in brake fluid.
  5. Open the bleeder valve 1/2 - 3/4 of a turn.
  6. Have an assistant depress the brake pedal slowly and allow it to return. Continue this pumping action to force any air out of the system. When bubbles cease to appear at the end of the bleeder hose, close the bleeder valve and remove the hose.
  7. Check the level of fluid in the master cylinder reservoir and replenish as necessary.
  8. After the bleeding operation at each wheel cylinder has been completed, fill the master cylinder reservoir and replace the filler plug.

Do not reuse the fluid which has been removed from the lines through the bleeding process because it contains air bubbles and dirt.


  1. Perform the "Bleed Brake'' procedure with the DRB II scan tool. This procedure is described in the DRB II software information and diagnostic guide.
    1. Attach the DRB II scan tool to the diagnostic connector.
    2. Run the Bleed Brake procedure as described in the DRB II tester guide.
  2. Repeat the conventional bleeding procedure as previously outlined.
  3. Fill the master cylinder reservoir to the proper level.
  4. Check the brake operation.


Hope this helps.

Apr 21, 2013 | Jeep Wrangler Cars & Trucks

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

Step by step instructions on replacing front and rear brakes on 1993 camry


1) Jack up car
2)remove lug nuts
3)remove tire
4)unbolt brake caliper
5)remove old brakes
6)install new brakes
7)reinstall break caliper
8)reinstall tire
9)reinstall lug nuts
10)let car down
11)repeat procedure for other wheels

Jan 16, 2010 | 1993 Toyota Camry V6

2 Answers

How to replace the rear brakes for mazda 5 2007, if there is step by step procedure it will be appreciated


This should be a disc brake setup in the rear, you will need a special tool to push the piston back into the caliper, they do not push in like the old style calipers, they actually have to be turned while being pushed in. You may be able to find the tool at the local parts store. Just tell them you need the tool for the rear brake calipers for your vehicle. Hope this helps

Jul 15, 2009 | 2006 Mazda 5

1 Answer

Replacing rear brakes on 96 deville


quite an involved repair if unfamiliar. Include proper setting of park brake arm to get proper pedal height , or the pedal might go to the floor.. Also includes bleeding of the brake system, with a power bleeder.

Mar 27, 2009 | 1996 Cadillac DeVille

1 Answer

Need to replace the brake light.


Go to collisionrepairadvice.com to get your answers quickly, Gives step by step procedures and who to go to to save money$

Mar 23, 2009 | 2000 Buick Park Avenue

Not finding what you are looking for?
2007 Toyota Camry Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...