Question about Mercedes-Benz ML320

1 Answer

I have the wait signal - ML320 Mercedes-Benz Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

Is this a diesel engine?

Posted on Nov 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Truck will be running fine, then all of a sudden it will completely shut off. After we wait a few minutes and pump the clutch and make sure it is all the way to the floor it will start, sometimes. S


You need the engine computer scanned for fault codes, i thank you have an ignition control problem like a module or distributor pickup coil issue. These parts whenthey fail should leave fault cdes so get them read.
Next, the check engine light will pause shortly followed by the second digit of the trouble code. For example if the check engine light blinks once and pauses followed by six blinks the trouble code number would be 16. If no code is present the check engine light will stay one constantly. To restart code gathering turn the ignition key to the "off" position, wait three minutes and turn the ignition key back "on" again without starting the engine. Remove the jumper wire once code gathering is complete. To clear code after the repairs have been made remove the negative battery cable for one minute and reconnect.
toyota_dianostic_connector.jpg
Toyota Diagnostic Connector
Toyota Code Definition Table
Code 11 Momentary interruption in power supply to ECU (electronic control unit or computer) up to 1991
Code 12 Engine revolution signal missing Code 13 Rpm signal to ecu missing above 1000 rpm
Code 14 Igniter signal to ecu missing
Code 16 A/T control signal missing from ecu
Code 21 Main oxygen sensor signal fault
Code 22 Water temperature sensor circuit fault
Code 23 and 24 Intake air temperature signal fault
Code 25 Air/fuel ratio LEAN
Code 26 Air/fuel ratio RICH
Code 27 Sub-oxygen sensor signal or heater circuit fault
Code 28 No. 2 oxygen sensor/heater signal fault
Code 31 and 32 Air flow meter circuit or Vacuum sensor signal fault Code 34 and 36 Turbo-charging pressure signal fault
Code 35 Altitude compensation sensor signal fault
Code 41 Throttle position circuit fault
Code 42 Vehicle speed sensor circuit
Code 43 No starter signal to the ecu
Code 51 AC signal on; DL contact off (in transmission shifter with diagnostic connector jumped)
Code 52, 53 and 55 Knock sensor fault Code 71 EGR system malfunction
Code 72 Fuel cut solenoid signal fault
Code 78 Fuel pump control signal fault
Code 81, 83, 84 and 85 TCM communication fault

Jun 28, 2012 | Cars & Trucks

1 Answer

No activation signal for fuel pump or fuel injectors from computer when hot.


...signal is brought low, the "Wait to Start" lamp is turned on. The glow plug lamp is controlled by the following sequence: PCM lights the WAIT TO START light after a key on

Nov 28, 2011 | Honda Accord Cars & Trucks

1 Answer

After replacing my battery, I am unable to start the car without hitting the alarm reset under the dash. A mechanic told me to turn the key up to crank, quicfkly 5 times to reset. That did not work.


PLACE THE PROGRAMMED KEY IN THE IGNITION SWITCH. FOR THE FIRST KEY. TURN IGNITION SWITCH ON AND WAIT 3 SECONDS RETURN TO OFF POSITION AND REMOVE KEY. FIRST AND SECOND PROGRAMMED KEY OPERATIONS MUST BE PERFORMED WITH IN 15 SECONDS. INSERT SECOND PROGRAMMED KEY AND SWITCH IGNITION ON. WAIT APPROXIMATELY 10 SECONDS. ENSURE IMMOBILIZER WARNING LAMP BEGINS TO FLASH AND AN ACOUSTIC SIGNAL IS EMITTED.SWITCH IGNITION OFF AND REMOVE KEY.WITHIN 50 SECONDS INSERT NEW KEY AND SWITCH IGNITION ON.WAIT APPROXIMATELY 10 SECONDS.ENSURE ACOUSTIC SIGNAL IS EMITTED AND IMMOBILIZER WARNING LAMP REMAINS ILLUMINATED FOR 3 SECONDS INDICATING PROGRAMMING COMPLETE. FOR EACH ADDITIONAL KEY REPEAT PROCEDURE STARTING FROM THE BEGINNING.REPLACEMENT KEYS CAN ALSO BE REPROGRAMMRF USING DIAGNOSTIC EQUIPMENT.MAXIMUM 8 KEYS CAN BE REPROGRAMMED.

May 21, 2011 | 2005 Chrysler Sebring Conv

2 Answers

I have a 1995 grand prix Blinkers dont work but, other lights do.


First check turn signal fuse and relay if, they are good then try pressing on and off the hazard switch while turning the signal switch on.If signals start to work replace hazard switch.If hazard switch is good then replace turn signal switch.

May 02, 2011 | 1995 Pontiac Grand Prix

1 Answer

After replacing the battery on my Porsche Carrera 2000, I entered the wrong numbers a couple of times on the radio screen asking me to enter 4 digits and then the screen went on a WAIT signal. Now that I...


Yes - there is a solution here.

The problem here is that you must leave continuous power to the radio until the WAIT period is over. Any interruption to the power causes the countdown or wait period to start all over again. The secret is to ensure the key is turned in the ignition to accessories point I or the first point on the ignition that activates power to the radio.

If the key is not turned in the ignition as outlined, the radio will automatically shut off after one hour which is a power saving feature (which is great) but it also has a side effect in this case of shutting off the radio before the time limit has been reached!!

Obviously - as you must leave the key turned in the ignition during the wait period (which may be up to 4 hours) please ensure the vehicle is parked in a safe location and well away from any opportunistic thief.!!

Hope it helps or for anyone reading this in a similar situation - this information applies to many vehicles and radio types as many manufacturers have a similar security feature.


Additionally - for cheap code retrieval for Porsche and many other car radios please see this link.

Thanks for using FixYa.

Mar 18, 2011 | 2000 Porsche 911 Carrera

2 Answers

After flat tire, tire pressure warning will not go out even after making sure pressure is at 44psi. How do I reset dash?


44PSI?? is that what your car recommends...


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

Aug 14, 2009 | 2006 Hummer H3

1 Answer

Car shakes when i am waiting for signal or on nautral.


check the engine supports. maybe one of the supports has to be replaced.

May 05, 2009 | Volvo 740 Cars & Trucks

1 Answer

2001 Buick Regal cuts off while driving at times also won't start


The ignition switch on that model is rated @ 50amps. When I was driving my 2001 Regal LS (at 120,000 miles) and used the turn signal, the engine would die, when I switched the turn signal off, the engine ran. So I replaced the ignition switch, and all is well.

merkfritz@yahoo.com

Mar 24, 2009 | 2001 Buick Regal

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...