Question about 1999 Jeep Wrangler

2 Answers

I have changed my blower motor, my control switch and my resistor and my blower motor will still not come on. What else could it be?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

I would check the fuses, make sure you have power and ground to the blower motor. Your ground is what switches the speeds on it, You can easily test this with a test light.

Posted on Nov 05, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 133 Answers

Have you checked your voltage at the switch to see if any is there?

Posted on Nov 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater switch replacment


Hello! it's my job to make things as easy for the customer as possible...Therefore I must ask why you want to replace the heater switch? Is it because you have lost one or two of the switch speeds? Your vehicle is noted for loss of the Blower Motor Resistor...
Changing the Heater switch means removal of the Climate Control Assembly which is not the easiest of jobs...I've included the process...But are you sure the blower resistor is OK? If you have lost 1,2, or all blower motor speeds it's more than likely the Resistor pack. And a lot easier to change...
Guru...saailer


Remove climate control:





12_26_2011_2_15_09_am.gif
  1. Remove the instrument cluster finish panel...
  1. Remove the 3 climate control assembly screws...
  1. Disconnect the climate control assembly vacuum connector...
  1. Disconnect the 5 climate control assembly electrical connectors...
  1. Remove the climate control assembly..
Removal of blower motor Switch:
  1. Remove the climate control assembly.
  1. Remove the blower motor switch knob.
  1. Remove the blower motor switch.
    1. Remove the screw.
    1. Remove the blower motor switch.

Removal of blower motor Resistor:


12_26_2011_2_22_49_am.gif
Blower Resistor is under the battery tray...

MOTORCRAFT Part # YH1698 ...cost $25

12_26_2011_2_28_50_am.jpg

Guru...saailer

Dec 22, 2011 | 2007 Ford Econoline

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

1 Answer

Blower only works on high speed in 2003 focus


BLOWER MOTOR WORK ONLY ONE SPEED.YOU COULD HAVE FAULTY BLOWER MOTOR RESISTOR OR BLOWER MOTOR CONTROL SWITCH BAD.USE VOLT METER CHECK VOLTAGE AT EACH CONTROL SWITCH SPEED TERMINAL. IF POWER IS AT EACH TERMINAL ON CONTROL SWITCH YOU MORE LIKELY HAVE A BAD BLOWER MOTOR RESISTOR.

Sep 26, 2011 | 2003 Ford Focus

1 Answer

Need to locate the motor blower resistor for my 1999 mercury mountaineer, it has dual air, the resistor for the back is fine but the one in the front is bad and i cannot locate it. Please help.


If you have a manual system, you have a resistor. If electronic, you have a blower motor speed controller. Please rate if this helps.

here is info:

Control System Outputs-Manual A/C
Blower Motor Switch Resistor
The heater blower motor switch resistor has the following features:
  • The assembly is located on the evaporator housing in the engine compartment.
  • Three resistance elements are mounted on the resistor board to provide four blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the blower motor circuit to decrease or increase blower motor speed.
  • An overheating protective device (thermal limiter) will open the resistor coil circuit when the temperature reaches 121°C (250°F) interrupting the blower motor operation in all speeds except HI.
  • The thermal limiter cannot be reset and is not serviceable.
Control System Outputs-EATC
Blower Motor Speed Control
The blower speed control is located on the evaporator housing in the engine compartment.
  • The function of the blower motor speed control is to convert low power signals from the electronic automatic temperature control module to a high current, variable ground feed for the blower motor (18527).
  • The blower motor speed is infinitely variable and is controlled by the electronic automatic temperature control module software.
  • A delay function provides a gradual increase or decrease in blower motor speed under all conditions.

Jan 10, 2011 | 1999 Mercury Mountaineer

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

I have 2002 infinity I35 and the blower motor stop working ,I took out the blower motor to make sure was good. YES the blower motor still working .the only think I really don't know how to check is Blower...


WELL YOU HAVE TO USE A VOLT METER CONNECT ONE VOLT METER WIRES TO GOOD GROUND AND THE OTHER VOLT METER WIRES GOES TO EACH SWITCH SPEED.IF VOLT METER GET VOLTAGE A 1 OR 2 CONTROL SPEED RESISTOR BAD.IF RESISTOR BAD YOU WILL GET 1 OR 2 BLOWER MOTOR SPEEDS.IF BLOWER MOTOR WORKING.CHECK THE AC AND HEATER CONTROL SWITCH FUSE OR CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL GOOD SO FAR CONTROL SWITCH ITSELF COULD BE FAULTY.

Nov 05, 2010 | Infiniti I35 Cars & Trucks

2 Answers

Need to change fan motor control switch? Only works on high setting.


this problem is not caused by the switch, it is caused by a defective blower motor speed control resistor, the resistor is located near the blower motor.

Sep 22, 2010 | 2003 Mercury Grand Marquis

1 Answer

1999 grand marquis were the blower motor resistor is located


this is for manual heater system. If you have electronic (digital display) you don't have one. Instead you have a blower motor speed controller.

here is info

Control System Outputs—Manual A/C
Blower Motor Switch Resistor
The heater blower motor switch resistor has the following features:
  • The assembly is located in the engine compartment on the evaporator housing toward the center of the vehicle.
  • Three resistor elements are mounted on the resistor board to provide four blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the A/C blower motor circuit to decrease or increase A/C blower motor speed.
  • An overheating protective device (thermal limiter) will open the resistor coil when the temperature reaches 121°C (250°F) interrupting the blower motor operation in all speeds except HI.
  • The thermal limiter cannot be reset and is not serviceable.

Dec 12, 2009 | 1999 Mercury Villager

1 Answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

Not finding what you are looking for?
1999 Jeep Wrangler Logo

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...